Polaris RZR 900XP build series Ep #1 UTV SNORKEL install!, PowerModz!

[@Krackdskul]

You know a guy cares more about his machine breathing than himself when the snorkel stack is above the driver's head!!! Nice build video

[@aaravclark3968]

Instablaster.

[@mirandayoung125]

Hell yes that was a great step by step install for your razor..gd wrk!

[@hav1byte]

Wow, well done, a lot of thought and cool end results

[@wraith511802003]

Nice i just got a 2015 rzr 900 s, this look like a must do mod.

[@captseamus]

Every 45°or 90° bend reduces air volume and velocity... straight runs

[@PowerModzOfficial]

Good to know Dirk, after about 10 mins in the water the clutch housing took about a teaspoon of water so I'm going to seal everything up with silicone, have to put a clutch kit in first. Thanks for watching!

[@PowerModzOfficial]

Not yet, keeping any eye on it though - and will probably open a hole up to let air circulate.

[@yamaman28]

thanks for the vid, there is lots of mud and water in BC so snorkels are a good idea, I just bought a 2013 xp 900

[@StreetersGarage]

You need to silicone those joints. The ABS cement will harden and become brittle over time and eventually create a leak. ABS pipe and cement are not really rated for vibrations, it's main use is for drainage of water and waste.

[@jacobdabal9209]

I may be wrong but that black tubing you removed from the fuel rail looks to be like it was a vacuum line. What you connected it to looked very much like a fuel pressure regulator. And if those are anything like most cars and trucks the fuel pressure regulator is connected to a vacuum. Just something to look into

[@bzugoo]

Iv'e been out all day in thé sun spreading horsemanure whit my tractor and i just Opend up a Cold Beer and then i see that you have uploaded halfour Long video :) cudos too you. And sorry for thé very bad english, its not my native tounge...

[@iceracer300]

You can put an adapter on the big pipes and run the clear tubes in their to clean it up.

[@PowerModzOfficial]

Thats a great idea!

[@GarnettM]

I was going to mention was if you got some steel tire valves and drill the tube thread the valve in and you can put the hoses to them anywhere they`ll hold good .

[@ericsteelers11]

i like that orange ski you got

[@bullishrhino7682]

i like your snorkel build over a lot of others i have seen. I am going to go to the hardware store. I never seen the list of all parts needed. Where can I get it.

[@cplpinker]

Love the build,

[@juniorhorndog69]

I liked the video. You ran 3 pipes. Couldn't you just run one 6" pipe for all of them?

[@dennyroe6839]

not all suck air the belt housing blows air a little

[@juniorhorndog69]

ok I'm hoping to get a rzr 1000 this year. do you have a video that shows people how to do it or is it the same way?

[@djnemesis82pluss1877]

ANY IDEA WHAT YOU SPENT IN PARTS TO DO THIS ? DEBATING GETTING A PRE-MADE KIT IM SURE THEY'RE A BIT MORE BUT WONDERING HOW MUCH MORE

[@MarijnKramer13]

Nice video's I have to say, are you going to do peformance exhausts and braked too? I want some other brake kit for my supercharged mavrick 1000, its got way to mutch power for the standard brakes (210 hp @ the wheels)...

[@ddddevyn]

on the rubber to abs, you can just use grease and clamp tight. on any abs bends, silicone is better

[@98zook]

great video, very informative. i am going to increase my rzr 800 airbox intake to 3" based on info from todd at hunterworks. some ow

[@GarnettM]

Are`nt those impact drills good I have the same kind , Nicely done the hardest part about doing this is the gluing Abs don`t give ya much time .

[@mikepaulson6154]

PowerModz whats the difference in just running a 2" for the air instead of 3" similar to the 800 just wondering why 3" and how bad would it be to run a 2" air instead

[@danburch9989]

Powermodz's point about two 2" isn't the same as one 3" shows that one should always hone their math skills. Just about every day math comes into play regardless of what you do. A single 2" pipe gives you 3.1" of cross sectional area of intake capacity; lots of air resistance to air flow into the engine. Two 2" pipes gives you 6.28" of cross sectional area of intake capacity; more resistance to air flow into the engine. One 3" pipe gives you 7.4" of cross sectional area of intake capacity; almost no resistance to air flow into the engine.

[@matthewbrandt2378]

I put a snorkel on my ranger its awesome.

[@pet390]

Can I ask you where can you find the Build list of the partsy used I have the same exact year as this and would like to copy your design

[@willredbird1]

Have u had any problem with the back panel behind the seats burning? From no air getting blown on to the headers

[@bullishrhino7682]

my air box leaks. What is the best thing to use or do to assure only air is getting in my box. I have seen sand getting by.

[@PowerModzOfficial]

check your seal

[@ddddevyn]

i was about to say that! run them into the cvt exaust pipe.

[@ryanhenry8252]

Would you sell factory air intake system? All the hoses, bolts needed

[@hunterhartley583]

Off topic, but I noticed the mini z in the back ground. I'm just saying if you fit the 700 into a mini that would be ridiculous!

[@marcodz1]

Hey I love your videos they are very helpful. I need some help I was thinking about getting the airaid cold air intake snorkel kit part #883-300, what else do I need too do so I don't get water or mud into the motor?? I have a 14 Polaris rzr 900 stealth black pls help.

[@as333as]

That's not a snorkel. Looks nice, but it won't keep the water out. The fender is not sealed to the intake on the inside, it's just a bit of foam to seal the two surfaces.

[@PowerModzOfficial]

as333as I suggest you check out my "Amphibious RZR" video and the others where it is submerged to the top of the snorkel for long periods of time with the engine running - it works great!

[@as333as]

PowerModz Sorry, I meant the air raid kit marcodz1 mentioned is not a snorkel...I know yours works, I even went to the show in Toronto to get a better look! I'm going to be doing a similar snorkel to my Jagged X before spring. Trying to find a way to move the pipes off to the sides so I can keep visibility as good as I can out the back...

[@PowerModzOfficial]

as333as oh ya i understand!

[@TheTor12]

And now u need The turbo!

[@timlaaksonen]

do a shop cleaning video!!! before middle and end!!! i seen lots of toys

[@willredbird1]

Because the exhaust from the belt housing is not blowing on to them

[@djnemesis82pluss1877]

So u trust the air filter box and clutch cover to not leak without any sealant ?

[@PowerModzOfficial]

The air filter is tight - i never sealed it, the clutch cover i'd seal if going in deep water.

[@Djm9393]

what impact gun are you using here bro

[@jayyyinkdd2326]

Can i have the lengths of everything you used

[@masonshuey3130]

At 15:25 there is a orb on the right

[@MerpSquirrel]

Thats a fuzzy.

[@nick81lax]

are you going to build a polaris ace?

[@PowerModzOfficial]

wish I could

[@garsonbrent]

just use aluminum or stainless mandrel bent tubing and silicone joints looks way better than cheep abs it is almost 20000 to get one of these things why buy your parts at home depot

[@gonzalotorres4377]

Yo quiero uno y el que tiene me gusto mucho

[@supersportsexotics31]

You should help me with my Atv👌 please

[@500renagade]

like your vids but i see many ways you cobble stuff.

[@PowerModzOfficial]

just get er done!

[@1996blackgt]

I would not put a bunch of sewer pipe on my RZR.