Polaris Sportsman Wheel Bearings on Amazon - amzn.to/2VRsi2c Bearing Press Kit (Recommended) on Amazon - amzn.to/2pyXHu5
@christophermcdermott23142 жыл бұрын
Brilliant help. Just got a polaris 2003 sportsman, and really useful to see what you do. Thanks!!!
@waynehoberg16559 ай бұрын
Bought a hydraulic press for 150.00 and race blocks for 20. What a time saver.
@speedfreak82002 жыл бұрын
Go to Harbor Freight & buy some Cotter pins they are cheap that way you always have a fresh one for the next job Thanks for the video I'm helping my riding bud,
@goneriding32685 жыл бұрын
good simple video giving me courage to go do my own wheel bearings thankyou
@bb1599-c2o6 жыл бұрын
Next time loosen the center hub nut BEFORE you remove the wheel, and the machine is on the ground. No need for any pipe methods, etc.
@Tristan10210011 жыл бұрын
my kawasaki is a 2003 model, it has been through hell and back many times and the front bearings are still good. they roll freely and do not slop. i only had to take the axle nut off to get to the bearings inside the drum while i was checking the brake pads
@socargamecks11 жыл бұрын
Awesome job!! I love the way you face forward through the UN-important areas. Thanks
@socargamecks11 жыл бұрын
It did. Couldn't find the correct sized deep socket to use to drive out the old ones so I used a 2 5/16 inch hitch ball. Not the easiest but it worked. Thanks Again!
@dansbrega40075 ай бұрын
Like always great videos
@benjaminfuller33994 жыл бұрын
I've learned so many stuff from your video I have a sportsman like yours but it's 2002 but I inherited it had a snapped axle theee torn CV bootsi fix think to you video and I got to do the rear bearings cuz they're warped because of the axle snapping
@JimForster9 жыл бұрын
This is my plans for the weekend - excellent video. I think even I can pull this off! (I went the easy way and got a press, but good to know there are other viable options)
@JimForster9 жыл бұрын
***** Well,that was the plan - the carrier didn't want to release the hub... Finally got them apart and now 1/2 the bearing is stuck on the carrier side - balls exposed on hub. I think this just got expensive.
@toma2tone2a107 жыл бұрын
Good Info Mark. Thanks for the tips. Love your comment at 7:02-7:04 (Not Bleeding Yet) Ha Ha, Great video.
@adrew19635 жыл бұрын
my axle is stuck hard in the housing I was wondring how at 10.40 in your video you just pull yours out can I bang the crap out of the cv axle to dislodge it
@destinhook38269 жыл бұрын
PLEASE REPLY. My Polaris Trailboss 330 has some problems with the bearings. It sounds like dirt or mud in the bearings in the rear end. Is it some sort of axle bearings or wheel bearings?
@upnorthvlogs2 жыл бұрын
Just paid someone $250 + to change mine 2015 570
@Pittsburghpilot4 жыл бұрын
If you heat up the hub with a propane torch just a little bit that bearing will pop out with one smack! To install the bearing again a little heating of the hub and the bearing will literally slide in without any force needed!
@enteryouremail688 жыл бұрын
Thanks for the great video.
@jasonleeward19724 жыл бұрын
Thanks
@benjaminfuller33994 жыл бұрын
What size socket do you use to punch out the old bearings and is it normal for both rear bearings go out before the front
@reno420999919 жыл бұрын
This helped alot! Thanks!
@TheTechGuider4 жыл бұрын
Get an impact man. Save the hassle
@639Beaver11 жыл бұрын
Have you considered an electric impact on all bolted ? Question, Using a pipe on ratchet could it possibly add to much torque causing it to break? I am a novice, trying to learn. Thank you.
@BigBobby0925 Жыл бұрын
I use a fwd axle bearing press and I don't even have to take the hub off the 4wheeler.
@mistered293 жыл бұрын
Are the bearings pre- greased?
@donnickles49533 жыл бұрын
i have a 2006 efi - will the above links for amazon work? it doesnt look like the bearing puller is a specific product - thank you !
@donnickles49533 жыл бұрын
can you post new links for me ? thank you
@everyonelikesbigjim2 жыл бұрын
Let's see smokie burnouts with that Camaro
@h8troodoh Жыл бұрын
" I'm not bleeding anywhere, yet"... 😅🤣😂
@ShaneHicks-v4o11 ай бұрын
Take bearing put in bag put in freezer. Heat cast with a torch old bearing will slip out, lube new bearing lil she will slide in easy no tapping
@ivansavchenko2036 жыл бұрын
Привет из России! А почему ты просто не нагрел ступицу? Подшипник сам оттуда выпадит и также легко встанет новый! Век живи век учись)))
@AaronGoSoFastАй бұрын
Got that clip out on the first try, huh? That shit took me 20 minutes.
@rzrkilleriwishiwereahonda36257 жыл бұрын
you need a press makes that bearing job a 5 min job. instead of beating up the
@erikdesormiers94588 жыл бұрын
would it be possible that it does a clicking sounds instead of a squeak???
@mikeyoung82174 жыл бұрын
set that rotor up on some wood blocks , be lots easier