Possible reasons your jeep does not have heat

[@sneekysmurf4754]

Just bought an 08 Liberty and no heat; I guess that’s why in here. I just wanted to say thank you for taking the time to do this video. I do appreciate you 🙇🏻

[@sharpcarco]

Well I appreciate you taking the to write me that message even though I know things are not going that well for you at this moment I greatly appreciate you as well thank you so much it always puts a smile on my face and I’m very sorry to hear about your troubles

[@sneekysmurf4754]

@@sharpcarco I have the same Jeep Liberty 08. I flushed the cores. My blender is moving the air from the floor to the vents. Could a water pump be my problem I mean it’s not over heating at all, I also changed the thermostat and I’m still only Geri g like 5% heat on low fan. Thank you for your time 🙏

[@sharpcarco]

Is there any chance you could scan the vehicle and find out what the temperature is getting up to? More than likely there’s air in the system and that’s why you’re not getting heat

[@sneekysmurf4754]

@@sharpcarco I can scan it tomorrow. But I’m in it now and when I turn the fan dial on low fan- I makes a little weird noise that I haven’t noticed before. I did flush it before and burped it. Maybe I didn’t do it properly. I will start fresh tomorrow with a scan. Thank you for replying

[@sneekysmurf4754]

I have an Ethos scanner I will use in the am. 🙏

[@florindocaraballo5516]

Thank you for your input. God Bless.👍👍👍

[@jamesoberg8809]

A few months before I needed heat again I had to replace the gasket on the water pump. The gasket only lasts about 5 years before it shrinks and starts to leak. I refilled the cooling system but didn't burp the system. Now with cold weather upon us , no heat. Flushed the heater core and burped the system. Heat is working again.

[@jamesbozza3800]

Thank you for your time. Very informative not long-winded and direct to the point great job thank you so much I'm a new subscriber

[@allanjohnson2552]

This is very helpful. Mine the fan runs but it doesn’t blow in any modes. I probably have to dig deeper by checking the blend door and the air intake.

[@frankking3146]

Hey so I’m Frank I’ve been working on a liberty 3.7 just like the one your working on for heat. So this customer brought it to me for a water pump. I replaced the pump. But after job I test drove it. And noticed it was misfiring. Did compression test and found cylinder 2 had no compression. So I let the customer know. I removed the heads and found intake valve and exhaust valves on that cylinder were burnt now also looking at pistons noticed that cylinder s piston had a chunk broke off it. There was a hole in piston. So i broke the car down pulled pan and ended up replacing all the rings ,pistons, honed the cylinders like in your video. Which gave me a brush up on my knowledge. I also ended up replacing valves and guides. The customer said since was tore down he wanted to take advantage of opportunity. Pulling the oilpan with motor in the jeep was a bitch had to remove axles and transfer case and drive line. before could get to pan. Anyway did the job put all back to get her with fresh gaskets and fresh parts for the parts replaced I started it and it was smooth. Up until the motor warmed up. It threw a P0123 code at me. So I replaced the throttle position sensor and reset all the monitors. Now I started and it’s running slightly rough. My next thing is going to check the plugs witch I’ve replaced already just to see if hauled up. I’ll keep u posted but if you can think of anything that could cause the slight rough idle would be appreciated. I’m aware of knock sensor crank sensor and cam sensors. I checked ground. Anything else?

[@sharpcarco]

You know I did that exact thing and I pulled the motor after all of the stuff that you’re talking about twice eventually finding out that it was just a bad coil… almost out of business but I didn’t do a lot of stuff myself. I had my guy do it…. He overlooked it.

[@andrewa5859]

you are probably the best person to ask this, im about to get my temps and my parents asked me to find a car and this is what I ended on and i just wanted to know for a mechanics pov is it? and gas milage isnt an issue for me really!

[@robertmullen2480]

THANKS cLAY I SUBSCRIBED

[@DeeWebb-zb7er]

At about 4:13 of the video you mention that you were going to make a video on replacing the blend air door motor. Did you ever do that? I have a 2008 Jeep Liberty and the vents are not blowing in my face. Any suggestions? Thanks!

[@sharpcarco]

Sorry, did not do that. I intended to obviously, but I haven’t got around to it yet

[@the2unicornsistersvlogs631]

You are the best

[@sharpcarco]

Well you’re the best to people like you keep me going thank you so much for writing that message I greatly appreciate it welcome to the channel

[@FairSquareLLC]

What is the fix video I got the exact same issue only good heat is on the on passenger side vent

[@mistydonaldson234]

I have a 2010 jeep liberty. My heat and ac stop blowing use to only work on defrost

[@beastlychase]

My car is doing the same thing isn't the heater core I don't think was it the blendor actuator? Mine seems to be turning but slowly and kinda stupidly

[@rigooceguera8273]

My 2010 jeep liberty blows warm air but not hot enough what coulb be the problem do you think?

[@philmcdaniel2357]

How do you burp the system? I have tried using the bleeder and just using the radiator cap, but It is still overheating, and my heat still wouldn't work properly.

[@eagleshadow101]

I have a 2008 Jeep Liberty. I have had issues with the drivers side blowing heat properly (some times cold, sometimes warm) while the passenger side remains hotter. I have had 2-3 flushes, water pump fixed, and the entire heater core replaced. My jeep apparently does not have an air cabin filter behind the glove box. What could be wrong? I've owned Jeeps before (1992 & 2001) and never ever had so much trouble with heating... Please help!

[@sharpcarco]

It could also be your heater blender doors even though that would surprise me. Luckily I knew that these were going to be a pain in the butt for somebody to put them back together. So I think I’m the only KZbin or to make video of that here’s a link to my playlist. I believe it’s called jeep linkage. I hope the information is helpful and useful for you. if it is please just turn the volume down and let my playlist play for in front of back. I would appreciate it very much. If I help you I hope you’re happy to help me thank you very much God bless have a great day. I didn’t send you the whole G playlist because it would’ve took you some time to figure out which video I was talking about take a look at these and seeing if you seen any of them yet kzbin.info/www/bejne/j2TRh5idadurfcmf kzbin.info/www/bejne/g366iYeAjdRmeaM kzbin.info/www/bejne/iJjYlo2HqN2DfZI

[@cherylyncampbell-wz4or]

My 2013 looks similar but the whole unit that the climate controls on are different than yours I put in a whole new unit and fuse but still no heat? But the seats heat up? Why is this?

[@mauricioramirez9744]

Low coolant. Add coolant and should yield results.

[@sharpcarco]

You don’t say.. yes, it usually does but most people don’t know that

[@HB-de5nr]

How long should it take for the heat to come out in fridged temps? Mine is sounding really loud just idling or even as I drive and it takes 15 minutes to feel any heat even in 30F. is this normal? last yr I do not recall taking that long or sounding so loud. I do finally get heat but it takes so long... does this mean I need to get it fixed ? ty so much.

[@joachimjohan1215]

godbless

[@cherylyncampbell-wz4or]

I have a jeep compass north 2013 that the heater not working

[@armmata]

Are these jeep know for doors braking

[@sharpcarco]

What do you mean breaking?

[@marcoe1722]

2012 liberty. Heat wont work past fan level 2. Starts blowing cold air when i set it higher

[@sharpcarco]

Sounds like your blower motor resistor is went bad. Possibly the control but normally not likely when you have a couple of settings that don’t work on certain speeds it’s because the resistor is bad.

[@marcoe1722]

@@sharpcarco thanks for the speedy reply! Fckin jeeps right?

[@sharpcarco]

Not a really big deal to be honest with you the blower motor pulls quite a bit of current honestly it’s hard to believe that they last for any amount of time whatsoever. It’s not just a jeep thing though so that’s a good thing

[@homeboywinzz4763]

I have a 2008 jeep liberty. I have same problem. And my traction control turns on while driving and 4x4 light and 4x4 serve comes on at random times. Can you help with that?

[@sharpcarco]

Not a lot of help that I can possibly give you in that situation but more than likely you just have a bad wheel speed sensor getting it scanned and replacing the sensor will more than likely take care of your problem. Sorry wish I could be of more help take it easy homeboy

[@gabriel-kr5kr]

Clay way the best way

[@sharpcarco]

😎😎 you know it.

[@ZachArmstrong02]

Or just do what I did and remove the blend door actuator and bam heat works perfectly now

[@empirusconstructionltd.6526]

dose that actually work?

[@ZachArmstrong02]

@@empirusconstructionltd.6526 worked for me took it off and pushed it towards the engine heat works good asf now

[@jobrown7511]

Where is that located? My jeep Cherokee it was under the dash

[@ZachArmstrong02]

@@jobrown7511 should be on the driver side under the dash on the right hand side

[@jobrown7511]

I will try that.. I know when I had my Cherokee I had people tell me my heater core was bad, I lucked up found someone who showed me how to turn it for heat then back to air.. I would use a screwdriver.. this is my daughter's not sure if I am messing with the right thing

[@desibelliveau55]

What about the fan heather making a lot of noise when turned fast for blowing fast

[@sharpcarco]

That just means somethings fell down inside they’re generally squirrels or leaves or small branches you just have to open the hood rays of the plastic by the windshield reach your hand down there and pull everything out . When it’s not running

[@charles1412]

Heat went out in my 2011 Liberty. Pulled the filters, they were filthy. Both lines to the heater core were still warm from a 20 mile drive today. Only thing I haven’t done was “burp” it. The water pump was replaced last year, but heater has been working until yesterday. Not sure “burping” this baby will help. Could I be dealing with a bad heater core?

[@charles1412]

I’d also like to add that my blower motor is working ok. Just getting cool air from the vents.

[@sharpcarco]

Well what I would do is just add a little bit of coolant to make sure it’s up to the level properly and see if that helps you at all but I also would try to burp it out because it’s free and it doesn’t cost you anything

[@charles1412]

@@sharpcarco I tried burping it on the driveway, which has a decent incline. Nothing came out and the coolant levels looked good.

[@charles1412]

I went out and played with the temp switch going back and forth between hot and cold, then the heat started coming out. Thank God I’m not going to be cold tomorrow on the way to work. NY is starting to become seasonally “normal” and we had some sleet.

[@josephphilbin1853]

@@charles1412 2010 jeep liberty, changed thermostat, flushed heater core, topped off bleeding valve as well, started jeep up, ran for 10 minutes, heater core line hot, radiator line hot as well, turned on heat in jeep, blasted out hot air for about 10 seconds then went warm to cold. Water pump was changed 4-5 years ago, any suggestions? Thank you Joe

[@mistydonaldson234]

Ur jeep looks just like mine Inside. Why don't my flashes not work it's not the blub .no phone charger

[@medinadrumalot1641]

But if it needed to be burped, wouldn't it over heat then?

[@sharpcarco]

No not always like in the situation of the Jeep Liberty that I’m driving right now it has an air pocket trapped in the heater core lines which allow it not to heat up as quickly as possible but it never overheats

[@medinadrumalot1641]

@@sharpcarco and I don't believe it would be the heater fan cus it does blow air. And I know it ain't the module regulator cus there's no ticking sound . I just simply have no heat at all. And I have an 08 jeep liberty limited.

[@lilikayemarie]

I have a 2010 liberty sport and I have a coolant leak. I replaced my water pump and a few hoses, and the thermostat. My boyfriend thinks we need some different clamps since auto-zone gave us aftermarket clamps (it’s coming out right at the end of the hose he just replaced). I also have no check engine light but my jeep sometimes feels like it doesn’t want to go up hills and feels like it isn’t shifting right or something. Any ideas?

[@veronicahounshel7403]

Steep hills Ive always used the tow/haul button beings we live in the appalachian mountains and climb steep

[@veronicahounshel7403]

When we we would visit The Gatlinburg Tn area we experienced this jeep not shifting correctly or wanting to climb but tow/haul button on the console mid dash area handled that issue

[@sneekysmurf4754]

🙇🏻

[@Scott-p1e]

Helli