Potterton Profile 60 Not Igniting

[@edwardcopus3072]

Brilliant advice.You know your trade. Our profile 60E had what sounded like a similar fault (to what you've described). A BAXI engineer came round, miss diagnosed the problem as being a gas valve fault and due to the boiler's age said that he couldn't get new parts. He recommended us getting a new boiler (£2000). I did ONE google search (after watching this video) and got the replacement PCB for £50 off E BAY, and fitted it myself. The boiler now sparks up first time like it was new! Thanks again.

[@mikepayen9441]

I had this exact problem. Oddly the boiler would take up to 13 goes to ignite but once warm would run all day first strike, making this intermittent problem difficult to diagnose. So with your advice I fixed it in about 20mins with a second hand £30 unit from Ebay. Thankyou George you are a Supernova where a candle would do!

[@antonywills1965]

Thanks George that's exactly what we had. A reconditioned pcb got it working the next day after struggling to light for years.

[@mrash5059]

So my boiler went tits up and I watched you vid , I ordered the part on line eBay £45 reconditioned, fitted and it now works perfect, spot on thank you.

[@constantinahatsuli3385]

Hi george. my boiler is the potterdon suprima that is overheating. any ideas?

[@orhandurmus1869]

My boiler fires up really quick but does not stay on for long. Its fine for first 30 mins but, then I get 30secs of boiler on, followed by 2-3 mins of nothing, this repeats until the timer kicks in to shut it down. I wonder if this is the pcb or the boiler thermostat. Any ideas?

[@Adam-wu7vt]

Did you manage to solve the problem, that's exactly what mine is doing.

[@orhandurmus1869]

@@Adam-wu7vt I replaced my PCB but still have the same issue when it's on for hot water only. Doesn't seem as bad when the central heating kicks in

[@Adam-wu7vt]

@@orhandurmus1869 Thanks for the reply, if I have any success I let you know.

[@duncanpeddie123]

I had one today. Leak above boiler. Repaired leaks re filled system. Started process to ignite boiler, zone valve energised, pump run, fan on but no attempt at ignition. Tested T2 and T4, 0.9 resistance Which from the fault finding chart says check tubes aren’t kinked ( they weren’t ) and/or replace air pressure switch. New air pressure switch arriving first thing tomorrow. Will see what happens in the Arvo.

[@parenteseswebdev]

Hi is this like the sl

[@sherylbloodworth2382]

Thankyou.That is exactly what mine did.Found brilliant heating guy and excellent parts supplier and managed the whole thing for £200..

[@amm6569]

Hi George! Tried to comment on your other video about heating come on with the hot water. I have recently got this issue where when using my shower / any hot water tap, the two rads closest to the boiler heat up quickly. Long story short, I do need to replace the whole boiler regardless, but as it'll take some time for approval / new boiler installation, is it still safe to use when the 3 port valve is faulty? I still get nice hot showers, just noticed the rads get hot too. My CH & thermostat are off. I can live without heating while waiting for the new boiler but not without hot water! So would like to continue using it for the time being. Thank you.

[@carlhales7919]

sounds llike a diverter valve

[@mohammedsalam7570]

Which area do you work? Do you cover milton keynes

[@mandeeplalli4653]

PCb fault smack the black board relay and sometimes comes on brilliant video

[@cb9130]

What area do you work in?

[@stuarthenderson7663]

eBay sell them for £40 and it's easy to do so no engineer should charge more than £30 to fit, it takes minutes to swap

[@stuarthenderson7663]

£28 to buy Motherboard on Ebay. Fit 3 wires that clip in about 2 minutes. No need to pay £200. So much bullshit and no doubt a gas engineer will charge about £100 also for his time. I did it myself and its easy to do.

[@HarrisRallying]

Can you share the link for the mother board

[@stuarthenderson7663]

Just looked on eBay there is only one

[@ninja600j2]

Worked for me thanks

[@g007kh]

Help!

[@denisesaunders3067]

Goodlooking guy

[@joglou7247]

I wonder how many people watched this vid, bought & replaced a new board & it didn't work... I know I did.