Follow me on Instagram and TikTok @quetopiq #CHILLMOBB
Пікірлер: 157
@PowerAcoustik15502 жыл бұрын
That’s all clear! Love the support
@topiqchill2412 жыл бұрын
Your welcome
@teluvv662 жыл бұрын
I appreciate the pace of your instruction, the diagram, and the details of your explanation. Keep up the good work brother!
@topiqchill2412 жыл бұрын
Bro I really appreciate that because i needed that extra motivation and encouragement to do this KZbin 💯
@russellanderson6096 Жыл бұрын
I’m glad you dropped this because I’m sho’ll going through this.. right now. I have the same 12s and amp and when the bass hit too hard it goes into protection mode.
@wiillthebarbertv9415 Жыл бұрын
I fixed my problem with protection mode, make sure you have a clean input to the amp where it cuts out anything over 80HZ, it slaps now!!
@topiqchill241 Жыл бұрын
Got you bro thank for the advice
@ChaosTherapy7193 жыл бұрын
Those RZR1 2500Ds can push 1608 watts at 1Ω clamped with box rise factored. I've ran it head to head with a Deaf Bonce Atom 2000.1 to a single Sundown X v2 10D2 and as long as ya install a fan or 2 you can play full tilt for hours. Just wish it was designed with 0 gauge inputs instead of the 8 gauge, but for budget amp that can push a big boi SPL sub it's worth buying.
@topiqchill2413 жыл бұрын
No cap bro I’ve payed mines at 1 ohm and the amp would cut out I sent it back got another one and the same thing happens those gothic 12 beat harder than some name brands but I decided to got 0 Gauge big three install 16v battery in the trunk and upgrade the Alternator the whole 9. So I can bring you guys those bass videos and content y’all love stay tuned!!
@ChaosTherapy7193 жыл бұрын
@@topiqchill241 yeah, i ran all 1/0 gauge Sky High wire along with three different 300amp ANL fuse relays and used a couple 1/0 to 8 gauge distribution blocks to wire in the Razor. And I've gotta deep cycle AGM as my accessory battery wired to a 250amp battery isolator so I'm not drawing off my main battery and i upgraded to a 320amp alternator and big 3ed it. My voltage rarely drops below 12.5v
@ChaosTherapy7193 жыл бұрын
@@topiqchill241 in a few weeks imma be upgrading to 3 Sundown Xv2 10s and adding 2 more Razors to push em
@themosthighovereveryone96802 жыл бұрын
Good breakdown
@ayebaldhead51332 жыл бұрын
Series wiring drawing looks like that system gone thump. It mad a face 😂... Thanks for explaining this though my guy
@NorthFloridaAirGunner Жыл бұрын
I've ran them at 1 ohm for a long time now with no issues. If it protects on 2 of those subs the ground is poor, or your electrical is crap. Running mine in the truck on a singe 2ohm dual vc stroker wired parallel.
@topiqchill241 Жыл бұрын
No poor electrical. Stability was lower then required specs of the Amplifier. Along with an equalizer added which dropped impedance even lower bro. This video speaks facts. You’re the needle in the haystack that just didn’t have any issues.
@NorthFloridaAirGunner Жыл бұрын
@topiqchill241 bro, we are running 4 of those amps like that though. One in the crib, one in my truck, and 2 in my son's truck. And there's a lot of folks on youtube running them at 1ohm with no issues. Great little amps.
@Wlrdzz11 ай бұрын
Very informative sir 👏🏽
@topiqchill24111 ай бұрын
Thanks family
@zx14malik3 жыл бұрын
You are very clear and explain very good thanks
@topiqchill2413 жыл бұрын
Thank for watching @Malik
@mcdizzle77403 жыл бұрын
I got two of these powering my 15s. These little amp pack some punch. At first I just had one powering both subs at 4ohms and it hit hard but after adding the second one and wiring each sub to 2ohms all I can say is holy crap what a difference.
@Rigandfixit2 жыл бұрын
I had two on my 12 kicker and I blew two before I gave up on these cheap amps.. I got a taramps class d and this thing give me the real watt's..
@392_RHINO Жыл бұрын
Hey will this amp also be effective on highs and mids?
@miltonsmith7431 Жыл бұрын
@@392_RHINO it's for subs. it doesn't put out the frequencies needed for mids and highs. you will need a full range amp
@392_RHINO Жыл бұрын
@Milton Smith ok appreciate it but what do you recommend for me? I have a dodge charger with a 8 inch sub and 2 pioneer in a box
@miltonsmith7431 Жыл бұрын
@dasuaveologist5823 Pioneer subs in a box? I have a Ram 1500 with four Pioneer 6x9 and two MB Quart tweets running off of a Sound Digital 400.2 and this amp pushing a 10" sub. Power Acoustic makes a 5 channel version of this amp that puts out 100 watts a channel to 4 channels and the sub channel puts out 400 watts at 4 ohms and 600 at 2 ohms. RZ52500D Walmart has it for $152.
@leonsines2472 жыл бұрын
Mines been running 1 ohm for 3 years now no issues.. proper gain setting to prevent clipping.. and im using the same walmart subs
@fernandolaboy5279 Жыл бұрын
How i can give the right tune to my skars Sdr
@fernandolaboy5279 Жыл бұрын
What is ur tune setup
@leonsines247 Жыл бұрын
@@fernandolaboy5279 i used a cheap oscilloscope from amazon
@javierdelacruz9924 Жыл бұрын
shit helped out brother thanks !
@topiqchill241 Жыл бұрын
Thanks bro glade you liked the video stay tuned 💯💪
@joey4132 жыл бұрын
Got 2 gothic 12's with a 2500 razor Amp and I was wondering why it was cutting out .gonna get the bigger amp..thanks for the vid!
@topiqchill2412 жыл бұрын
You welcome Joey L.
@danielallison214 Жыл бұрын
Just get another amp and have each speaker it's own amp to push.
@danielallison214 Жыл бұрын
That's setup I have now and it hits hard
@Chadirrific3 күн бұрын
@@danielallison214so just get a second amp and wire each sub to its own amp?
@killahken7 ай бұрын
Just got this amp,and a Sundown 12💯
@topiqchill2417 ай бұрын
Good combination! That RZR1 will push that Sundown perfect
@stanmondzelewski92532 жыл бұрын
I clamped mine today. 3 4ohm svc 12s wired to 1.33. I got 555 watts rms
@mattlighty84Ай бұрын
I have one of these amps running on clean power pushing a 12 memphis m7 in a 90 buick lesebra in a 3.5 cubic ft box hit a 146 no bs😮
@topiqchill24127 күн бұрын
Very nice!
@stanmondzelewski92532 жыл бұрын
Your wired series/parallel. Each dvc sub is wired series 4ohmx2 is 8. Your taking each sub up to 8ohms. Then you parallel the 2 subs together. 8ohm÷2 is 4ohm. Best bet on that amp would be 2 2ohm dvc subs. Wire em series/parallel and end up at 2ohm load
@keithstinnettubd49432 жыл бұрын
So I had a 4,000 watt planet audio class D mono block 1 ohm stable with two batteries pushing 3 JL audio 12's behind the seat and 2 memphis 10's and 2 punch 10's under the seat of my 78 Scottsdale and I have to say for the money I had in it It was hitting crucial low beats.. you could hear me coming a mile away
@jake_break91854 ай бұрын
So you're saying you had three 12's and four 10's running off of only one planet audio 4000 watt mono amp?
@turtleguy420 Жыл бұрын
I had mine wire bridged on 2 1200W subs bumped amazing for a couple months then out of know where she barely even wants to bump just one sub,
@topiqchill241 Жыл бұрын
Bro you should of grabbed two 12s then bridged them. It would of survived a little longer… if I add any more power Ik for sure they will blow!!
@CookinItUpWithRae Жыл бұрын
I have two pioneer 12s (1400w) 400 peak 4ohmn single coil..😅 How can I wire these for 2 ohmn
@topiqchill241 Жыл бұрын
Bridge them together. Meaning connect positive to positive (+) and negative to negative (-)…. And connect both subs together on one channel on your amp
@ItsJustaJetta7 ай бұрын
I've had mine wired at 1ohm for ages. Just needed 40a fuses. Smart? No. Works? For now. Fire extinguisher? Equipped.
@topiqchill2417 ай бұрын
Well as long as you have your extinguisher you good
@matt2565 Жыл бұрын
They met to have one amp for each sub you can’t run 2 of one amp that’s under-powering them
@cobe1mllc2 жыл бұрын
You right mines pushing 2 12 square hifonics brutus @1ohm it gets hot as a fucking iron and go into protection mode I just crank up the a/c and it immediately gets going plus at night when I’m ready to go out and parking lot pimp it does good it never goes into protection mode ..still upgrading to Rockville or planet audio
@topiqchill2412 жыл бұрын
Amplifier up grades are alway better bro. Include the big three bro and a alt or dry cell battery to protect dry cell dimming
@robmitch58832 жыл бұрын
I got this amp running two kicker comp r subs straight slapping and it doesn't get hot I'm running 2ohms stable
@patrickblunt3652 жыл бұрын
You would’ve did better showing us by doing it instead of on paper lol
@topiqchill2412 жыл бұрын
Yes sir go wit the Rockville bro 1500watt true Rms
@lowpulse8729 Жыл бұрын
Being able to read schematics makes it a non-issue, either way? He’s good 👍🏾
@gabrielthegamerguy3 жыл бұрын
Got the same running 2 15s but I was driving home from work and boom it cut out so idk man fk that amp return that shit don’t get me wrong they fucking pushed hard asf
@topiqchill2413 жыл бұрын
I stopped using that razor amp Im upgrading my system soon grinding now. Stay tuned bro
@mcdizzle77403 жыл бұрын
Had the same problem....turns out it was the connection on the bass knob.
@kristopherdonaldson95693 жыл бұрын
Correct me if I'm wrong, but the way you're describing, you're only running one coil of each sub. Connecting the other +/- is pointless. And I'm under the impression that it's not good to run only one coil on a dvc sub.
@topiqchill2413 жыл бұрын
Yes I’m running one voice coil on each (dvc)sub to get a 4ohm load. Which is the lowest Capacity rating for the amp I used. Connecting the +\- on each dvc sub is very necessary when you are measuring impedance because the ohm load will fluctuate when voltage is applied. And a few other reasons. But I will be converting back to parallel wiring soon stay tuned.
@kristopherdonaldson95692 жыл бұрын
Try modeling your enclosure and subs in winisd. You can see the impedance curve of the enclosure and see what impedance your amp will actually be seeing. I have 2 dvc 8's. Dual 4ohm subs. I wired them parallel and they read .8ohm But in my box, my amp is only seeing a 3.6ohm load.. so I set my amp to deliver 650watts at 2ohms. It slams them two 8's like a boss, never gets warm, and never cuts off/protects. Run a scenario with winisd and see if you can wire yours like that.
@zoominnboomin2 жыл бұрын
I hooked up 4 12s to this amp and no protection. After I took them out and have only one hooked up, it's going into protection if I turn it up loud. Very weird.
@topiqchill2412 жыл бұрын
After having this amp I wouldn’t recommend it because Ive had 3 in the last year and they all do the same thing
@dominicgarcia85 Жыл бұрын
I have one speaker so I hope I don’t come across same issue
@topiqchill241 Жыл бұрын
You won’t bro unless u just abuse the amplifier by clipping it out at its peak
@kenh7333 жыл бұрын
Good video, one other thing thats important is dont use little tiny speaker wire, get big copper speaker wire, I had to learn about series wiring back on my first subwoofers back in 1985 before that in the 70s we didnt have all this fancy stuff, just a radio 8 track with a Kraco booster running 6x9s in the deck
@topiqchill2413 жыл бұрын
Appreciate the advice thanks.💯
@JuanRamirez-ud1zw2 жыл бұрын
So what I did was I hooked up negative to negative positive to positive on each sub then I hooked up one wire to each positive on the box and same on my negative then I grabbed my main lines from the amp to the lines I connected the two subs with and spliced it together what's that called
@topiqchill2412 жыл бұрын
It’s called Parallel Wiring. Commonly known as bridging .
@JuanRamirez-ud1zw2 жыл бұрын
@@topiqchill241 gotcha thanks
@zacharyeaslon66 Жыл бұрын
I’m still confused I have the scar ddx 12inch which is only rated for 1500 but the amp can’t even push it very hard without the amp going into protective mode. I’ve tried changing my ground but that made no difference cause I thought maybe I just had a bad ground. I’m running 4 gauge power and ground wire which should be fine
@topiqchill241 Жыл бұрын
Do you have the razor amplifier @zacharyeaslon66
@jordancameron444111 ай бұрын
I have the exact same setup except with the skar evl 15 and it’s never cut out on me… what kind of wire are you using for power, cca or ofc?
@brandoortiz42682 жыл бұрын
Got 2 kickers 4om whit the same Amp. The only difference is that on each speaker I only have 1 (+ )and 1 (-) how would you connect them ?
@topiqchill2412 жыл бұрын
Parallel because you have SVC(single Voice coil Subs.(+) to (+), (-) to (-)..
@danielallison214 Жыл бұрын
I just bought 2 gothic 12's and 2 rzr1-2500 amps and put each 12 in an individual box and it hits hard. Harder than my JL W6 12's PC2350 Precision power amp but this was 1997😂
@topiqchill241 Жыл бұрын
Most times those older amps perform better than the new ones
@djkeys415s Жыл бұрын
Theas amps will not go BELOW 1OHM!!!!! SO JUST DONT DO IT HOW DO I KNOW??? i have done it !!!
@topiqchill241 Жыл бұрын
Facts bro
@balloutsavage8912 Жыл бұрын
What if you have 2 dual 4 subs and an amp at 1ohms stable
@topiqchill241 Жыл бұрын
That would be a perfectly match system. Between amp stability and the subs impedance just tuned your amp so it won’t clip into protection
@claytonrothenbuehler1272 жыл бұрын
Had my skar 18 dual 4 ohm wired to 2 ohm and amp still kept cutting out brand new
@topiqchill2412 жыл бұрын
Those amps cant take the load of 2ohm only 4ohm compatible. My amp was only a week old and it constantly went into protection mode
@eddiepride69182 жыл бұрын
I got that exact set up,it beats hard,amp doesn't heat up but I started smelling voice coil,my gain nearly off,I can't figure it out.
@topiqchill2412 жыл бұрын
Those amp are only rated for one of those speakers.
@matt2565 Жыл бұрын
Because you are under powering the subs you’re meant to use one amplifier per sub you’re not supposed to run two of the subs off of this at the end it’s only 650 RMS watch it matches the speaker perfect so you are losing have to power that the subs should have
@fernandolaboy5279 Жыл бұрын
I have to 2 Sdr how i can give the proper tune for it
@topiqchill241 Жыл бұрын
It depends on your box and it’s tuning
@seandoody48332 жыл бұрын
What about 2 12 inch pioneers single voice coil 4 ohm to the power acoustik amp?
@topiqchill2412 жыл бұрын
With the single voice coil all you have to do is have a 2 channel amplifier and install them on their own separate channel
@JEHERETIC3 жыл бұрын
or get two amps or two 4 ohm single voice coil subs and eliminate the bs
@topiqchill2413 жыл бұрын
Appreciate the advice
@joshholden856121 күн бұрын
The rzr 3500 does less power than the rzr 2500 my guy look up amp dyno videos
@topiqchill24118 күн бұрын
Ik I’ve switched it up since then.
@eastsidethug7133 жыл бұрын
You can't always go by box specs with an 8 gauge to 4 gauge conversion adapter, and 8 gauge speaker wire,this amp will hit hard ass fuck at 1 ohm and even harder at .5 ohm with no problem 😊
@beakyboy22453 жыл бұрын
I got the same amp,and I did exactly what you said and it’s still going in to protect mode..I even just wired one sub and it’s still doing the same thing!! Could I have already damaged something
@beakyboy22453 жыл бұрын
It crazy because I had no problem for a couple days then boom the protect light start coming on and the bass goes in and out!! What else can I check
@topiqchill2413 жыл бұрын
@Beaky Boy Yes the channel on the amp has burned out. That’s what happened to my first Razor amp. I would recommend a stronger amp, a extra battery, & (The Big3 upgrade 0 gauge). If you don’t already have them.
@headbanger57843 жыл бұрын
@@beakyboy2245 u got it over powered..nothing wrong with amp
@destaylor9999 Жыл бұрын
@@headbanger5784 right...the voltage is too high apparently
@tungel21192 жыл бұрын
Got one pwr acoustik gothic 12 wired to 2ohm on this razor2500 watt amp. When bass hits at high volumes it’s goes in and out of protect mode. I thought 1 gothic at 2 ohms this amp could handle?
@topiqchill2412 жыл бұрын
Those Razor amps are over rated I would recommend a different amp
@destaylor9999 Жыл бұрын
Most likely your voltage is too high on the gains...I found that 38 volts is a good voltage with 2 ohms with 1- 12" sub
@wiillthebarbertv9415 Жыл бұрын
I’m having the same issue, seems like the power output changes high and low also
@jayjackson1590 Жыл бұрын
Wat if u runnin 4 of em
@topiqchill241 Жыл бұрын
You won’t have to worry about the amp going into protection, because your impedance is higher then the required stability of the amplifier’s specifications which is 2 ohms.
@donnie41912 жыл бұрын
Did you run this razor amp in your own ride? If so, is it true that they cause a lot of fm radio interference? If you say no then I will buy one.
@topiqchill2412 жыл бұрын
Yes a 100% don’t buy it
@djkeys415s2 жыл бұрын
NO THEY DO NOT
@topiqchill2412 жыл бұрын
@@djkeys415s i experience a lot of interference bro how about you make some videos for us showing how to fix that issue.
@djkeys415s2 жыл бұрын
@@topiqchill241 I never had that prob but it could be a lot of things Iv owned 6
@donnie41912 жыл бұрын
Thanks for the reply man appreciate it. Can't live without my FM radio so I guess that's that.
@j-rockeastwood201311 ай бұрын
Good helpful vid. 👍
@masyn3853 жыл бұрын
I got the same speakers same amp but nothing is coming through the sub
@topiqchill2413 жыл бұрын
Make sure you got power coming from your 12v wire. Make sure you’re grounded on a solid metal source. Also make sure your remote wire has good connection. Most importantly check all your wire to make sure there are no damages.
@jordancameron444111 ай бұрын
Bro this is cap as far as protection mode at 1 ohm. I have this amp with a skar evl 15 wired to 1 ohm and it’s played for hours every day. You have some other issue I think my dude
@topiqchill24111 ай бұрын
Bro listen to detail ok you have one evl 15 which is 2 ohm stability. It’s not going to go into protect unless you wire two dvc svc subwoofers parallel
@jordancameron444111 ай бұрын
@@topiqchill241 no you listen idiot. I clearly said it’s wired to 1 ohm. If you don’t have the experience to realize that’s possible to make a single dvc 2 ohm sub one ohm then you’re making bullshit videos talking directly out of your ass. Video reported for disinformation
@@topiqchill241 and on top of that what the fuck is 2 ohm stability pertaining to a speaker? Like I said you’re clueless
@bkh57462 жыл бұрын
Ya can run that amp 1/2 ohm ya just cant clip the shit out of it.im running mine 1 ohm with 8 gauge power wire and i bang it a hr and 15 mins everyday to and from work
@topiqchill2412 жыл бұрын
Bro check out my new video I purchased a 2000.1D it slams
@lv33452 жыл бұрын
what is correct wiring for single dual coil 1200 gothic 12 inch sub to 2500 watt razor amp
@topiqchill2412 жыл бұрын
It’s really your choice bro, I would go parallel because it’s 1 DVC sub and a 1 channel amp. Series wiring really comes into play when you have multiple subs or speakers
@stanmondzelewski92532 жыл бұрын
Most of the people hooking these up dont know anything about impedance or wiring voice coils. They do paralle because all they know is positive and negitive to positive and negitive
@topiqchill2412 жыл бұрын
That was me until I educated myself bro. Now I truly know if you are a bass head!! You’re going to spend that bag right on sub from the 0 guage to the hi amp alternator. But stay tuned more videos coming
@stanmondzelewski92532 жыл бұрын
@@topiqchill241 just redid my 4ga big 3 for a 1/0 big 4 today. Yestetday and tge day before was killmat install. Whole truck cab got deadened.
@rockyhodges29723 жыл бұрын
Pretty good man keep making videos Educate yourself a little more to explain better but Im digging your videos tho
@topiqchill2413 жыл бұрын
Appreciate the support and honesty. Cant do nothing but get better. I got more footage coming to the channel. 💯💯 Stay tuned
@djkeys415s2 жыл бұрын
That amp gets crunk at 1ohm all day long
@topiqchill2412 жыл бұрын
Yes sir It will perform until it gets hot and go into protect mode
@djkeys415s2 жыл бұрын
@@topiqchill241 I still have it
@djkeys415s2 жыл бұрын
@@topiqchill241 never had them amps to go into protect now did they get hot yes did they quit NEVER.and I know how to use amplifiers I know what to do what not to do when to do when not to do and that's why I can use any AMP cheap expensive
@michaellamb57813 жыл бұрын
You will never see 2500wats from that amp even in dynamic. But it easily does 650 to 750rms dynamic. And don't forget box rise imped.
@topiqchill2413 жыл бұрын
Facts I know I was getting around 600rms. Appreciate the advice.
@michaellamb57813 жыл бұрын
@@topiqchill241 I have one of those amps on 2 kicker c10s.
@Drillorz2 жыл бұрын
I have this same amp, it goes into protect mode at higher volumes, anyone know a fix??? I tried to rewire the ground and power already, I have a 2017 Audi a4
@topiqchill2412 жыл бұрын
What kind of subwoofers do you have??
@Drillorz2 жыл бұрын
@@topiqchill241 2ohm kicker l7 12inch
@Drillorz2 жыл бұрын
@@topiqchill241 it gets around 3/4 volume then just goes into protect mode and stops playing, could it be something with the amp settings or my car settings?
@topiqchill2412 жыл бұрын
@@Drillorz was your amp playing on all volumes when you first purchased it??
@Drillorz2 жыл бұрын
@@topiqchill241 nope it’s been doing this since I got it
@jaygodfellas67223 жыл бұрын
So wat way to do it series or parallel
@topiqchill2413 жыл бұрын
Series Wiring with two Dual Voice Coil subwoofers. Which would put them at 4 ohms. With a amp rated at 2ohms max capacity. This would help with the quality of you over all sound.
@lewismiller92812 жыл бұрын
Are you a Scientist????
@topiqchill2412 жыл бұрын
No bro just did some research 🧐 😎
@Star-bo4wf2 жыл бұрын
Mine is stuck in protective mode no green light fuses are good was running a 12 and a 10
@topiqchill2412 жыл бұрын
Try upgrading you 12 volt wire and ground first make sure ground is connected (paint free) to bare metal frame. Also make sure woofers are wired correctly