Power Stop Z26 brake pads. A quick driving impression.

[@barneyfzr600]

I installed the z26 pad & rotor kit on my '16 Charger R/T & think it's well worth the $400 I bought the kit for. @ about 50K miles, the rear brakes would squeal like crazy no matter what pads/rotors I replaced it with when it was stock. As long as you do the break-in procedure, you should be fine! Just hit 100K miles with the kit & no complaints. Hope this helps fellow Mopar families!

[@el34glo59]

I think they're so smooth that people feel they don't have the same stopping power. They do. It's just they don't bite hard initially. But they will stop when you need them too. But these feel smooth af and don't dust and are quiet. Just bed them in, a few times if u have to, and then give them a few days. They'll be up to snuff

[@erniearambula3525]

All ceramic material brake pads have less bite than your semi metallic but once you adjust your leg or foot pressure to your braking they perform much better than stock they're easier on your rotors there's virtually no brake dust or noise and my front ceramic pads have lasted for 2 years.

[@jda8176]

I have the Z23 kit on my RT and I love it, it feels smoother than stock and almost no dust!

[@soxfunny98]

Thanks for doing this video my friend. I have put them on a lot of my customers cars and they like the stopping and love that the pads are basically dust free. They all have liked them better than the Brembos EXCEPT for 1 customer. ANYHOW......... As usual you hit it on the head. That was a perfect.comparison!! Your the man B

[@bmasontv]

They aren't bad at all! The lack of dust by comparison is a very welcome change for sure.

[@glockmodder]

i have powerstop on my tahoe what i have noticed is they are a little soft until you need them the harder you hit them the better they work pretty amazing with 5500#s

[@matthewsorensen2147]

I put them on my hellcat and 392 Challenger and I like it. Just put new rotors on front. most Mopar dealers want 1250 . A piece. Monster Mopar got them for 655. Plus shipping. Ask for Sam. New Mopar rotars have only 3 slots on each side. I think Mopar is changing them out with less slots, maybe to many cause heat at high speed braking. Not enough beef on old ones.

[@vincealince_SRT]

Glad you liked them, like I said in chat a couple months back, they’re well worth it.

[@yae2220]

I just bought some for my 86 Chevy caprice hopefully they do well

[@shawne7228]

How important do you think the initial heat cycle break in is? To be honest the stock 6-piston brakes are super grabby stock. So maybe z26 pads will actually have nicer feel. What about swapping them in the rear? Or did you only do the front.? Thanks for the video.

[@bmasontv]

Only did the front, but I was very particular about the bed in procedure.

[@paulturbo69]

i have these on front of my z32 with 354mm Street warrior discs & pads with adapter brackets. Better upgrade from stock dated 90s calipers 😮

[@mikebrownlee9753]

I bought a set my scat been to the track couple times with them slows down pretty good just by stabbing and releasing

[@lifeofmike556]

Hey Mason just installed these on my 2011 Mazda Miata. So, I thought the same thing. The initial bite when pressing the brake is pretty stock... Kinda bummed. But, when you stand on the brakes they definitely stop harder and faster than OEM. So my plan is, keep the power stop rotors and pads. Get through winter and soon as summer comes around I'll do some EBC yellow pads because what im looking for is the first initial "bite" overall the PowerStop pads are good and better than OEM along with the rotors. For $185. I'm extremely happy

[@BMan100]

So on a daily drive deal, they are as good as the stock brembos in your opinion. Thanks...i'm glaring at the not so "loved" SRT 392's. Missed my chance to order one from the factory (I live by it lol) being Anal retent I'd want to keep it OEM, but a grand ( CDN) for one brake disc is a bit over kill, what's your impression on those Replacement Rotor rings though?

[@johnk815]

My 19 scat with dynamics package has a braking performance gauge. I’m going to try mine. I’d like to see what your 60-0 is.

[@JorgePerez-ki6pz]

did you buy these, im contemplating buying these but im afraid I won't get the right pads

[@johnk815]

@@JorgePerez-ki6pz no I still have original pads in. 9000 miles. There dirty but work great

[@MegaHollywood1971]

Z26 material doesn't have much bite. If you have a high horsepower car and "Hoon", then semi-metallics are for you. There really isn't a replacement. Unless of course you opt for High Carbon rotors to aide with the bite. Having "clean" wheels isn't paramount when you have a behavior of higher speed.

[@mo198832]

That why I upgrade the brake hose to stainless steel and put high carbon rotors

[@jochenheiden]

The stock brakes on my Scat Pack are very squeaky. It's not wear indicator squeak, it's something different. Not sure why.

[@bmasontv]

metallic pads...

[@jochenheiden]

B Mason 🤦‍♂️🤦‍♂️🤦‍♂️

[@rtm6930]

The stock pads is not the main issue. It’s the rotor on one side. Their slotted for directional but all 4 corners are slotted the same way but the internal rotor cooling is for non-directional. I just installed the PowerStop front&back kit (Rotors and Ceramic pad) and it’s quiet like a Honda. I had Hawk HPS pads and these squeaked like the original Brembo pads. Jumping thru videos this weekend about Brembo and slotted direction I realized that dodge should have delivered our cars with proper slotted directional rotors. A couple people have remarked that the only time they have heard a squeak from Power Stop is when going in reverse. Of course this means their rotor is traveling in the opposite direction. I’m tempted to put my original Brembo pads back on since they only have 5,0000 miles on them to prove a point that they won’t squeak with the power stop rotors.

[@Superrun357]

ceramic brake pad lube. had the same issue, fixed it with a simple cleaning. pop the wheels off, two pins, pull the pads out, clean rotors and pads with brake cleaner, liberally lube the back of the brake pads where the pistons touch them. * disclaimer yes there are places you should and should not put brake cleaner and lube so do your research and be careful, wear gloves and don't get any brake lube on the front of the brake pads. I completely silenced and fixed the problem on my four pistons on the scat.

[@quefol5291]

Performance brakes will squeak until they are warmed up people buying race grade Porsche 911s were complaining about the same thing basically they have a higher operating temp range and will be noisy until they heat up and hit that mark

[@locohobo1925]

I never quite understood the brake dust issue... but I detail polish my wheels (whole car, really) every weekend... ‘low brake dust’ would never affect my purchase decision.

[@malamri424]

i got the z26 on my Jeep SRT... i totally agree, initial bite is worse but still way better value though. I ordered another set.

[@2ambaby198]

They are great I love 'em

[@CheesusSVT]

Just put them on my 03 terminator mustang, They are bedded in and are so quiet and smooth so far. Babying them until they are broken in all the way 😹

[@PS5ProGaming23]

How do you know when they are broken in all the way?

[@Billy-gh9ih]

@@PS5ProGaming23when they start to warp needing to be replaced you know they have already been warn in

[@tillman002000]

The dust on my Daytona 392 drives me nuts. The car is new and just fighting the urge to switch them out.

[@malamri424]

I've had these for a year, definitely lasts longer and absolutely no dust. Initial bite is not as good as OEM though.

[@phillipdale6765]

Thank you!

[@ScoutPL]

So how are they when used hard? I don't care about dust. I have EBC Blue pads on my Challenger track car. How would these compare with hard braking, repeated hard braking, the kind of braking that has my EBC blues just smoking?

[@bmasontv]

I wouldn't trust them for track use, aside from an occasional autocross...

[@hochgonzalo8923]

Two months after I purchased the Power Stop brake kit my right rear caliper failed and began leaking brake fluid. After waiting three weeks for the part, they now tell me the ETA is over a month away. This really sucks. I now have to buy and install a temporary generic caliper while I wait for the Power Stop caliper. Don't do it. Right Rear Leak. TT797144

[@buffaloaf8205]

Lol I put some of these on 94 Camaro with the rotors they are 10x Better than stock

[@sidyal1353]

I heard so many good reviews about Z23 but mixed reviews for Z26. Is it true..??

[@johnc.9133]

From what I understand, the Z23 and Z26 are the same pads with the exception to the heat dissipation shield that comes on the back of the Z26 pads.

[@johnc.9133]

Yup, according to PowerStop, they are the same pad. Just the shield and shims are different. And they are coated to help resist rust.

[@martyrogers1154]

If you are using them they should be more than adequate for my fiances veloster turbo. Just some weekend mountain riding

[@BartMan59]

Don't laugh, but I did a complete brake changeover (rotors, caliper, and matching pads) to PS Z26 kit my 2011 Lincoln Towncar; peace of mind to know the brake stopping is there if ever needed.

[@oleyeller3256]

Theres nothing wrong with improving braking performance or even running straight street+ or similarly high higher performance brakes on even a minivan bc it increases safety and could save you or your family's life. Same as entry level suspension upgrades on regular ole cars.

[@victorrobles2108]

Would you recommend for a regular RT 5.7 I'm looking for a better pad

[@bmasontv]

Yep. Good pads. Clean too.

[@tylerboes5642]

Hey brother quick question, and i know you haven't had your 392 in a minute but when you did, did you get it tuned and if so where?

[@bmasontv]

The initial tune was done by Peitz performance, I tweaked it. the transmission tune was tuned by myself.

[@tundrawhisperer4821]

Stupid question, but what do you mean by tuned? Thx

[@dustin9967]

Had them on my Durango SRT. They ended up glazing over and causing vibrations at high speed.

[@dustin9967]

BMWMED1 only a few thousand miles.

[@dustin9967]

BMWMED1 hopefully you have better luck. I did a few high speed stops after they were well broken in and something tells me the kinetic energy needed to stop the Durango’s weight is super high.

[@dkinley334]

Did you wipe the oils off of the rotors

[@jeffsmystic]

Thanks for the review 👍

[@MoEzArT_]

Stock hellcat already are with brembo pads, you getting powerstop pads is a downgrade in any area

[@bmasontv]

So far I would have to disagree. These pads have slowed my car down from well over 150 miles an hour on numerous occasions and that along with less rotor wear and 0 breakdust. I'd say they're an upgrade in every area. That being said they do not have the same initial bite that the stock pads have, that's fine with me.

[@ETRacing]

That thing got a HEMI? lol

[@rogerrameriez8912]

MO POWAH BABY 🤘

[@gsheverything_2716]

Nice one sir