Predator 212 build, Porting, Tech video, How does it work ? And why ? Explained Paulskarts.com

  Рет қаралды 3,999

Paul's karts

Paul's karts

Күн бұрын

Пікірлер: 34
@mikecondoluci53
@mikecondoluci53 Жыл бұрын
paul i think the word your looking for is swirl , thats a beautiful head with quench its a killer combination thank you
@xxnerfsniperxx
@xxnerfsniperxx 3 жыл бұрын
I ordered some valves and guides, I’m making a custom predator 212. I’m 15 too and I couldn’t be interested in anything else. Even this video is very informative. Thanks for someone who does custom head work and other things for other people. Good job.
@gameworkshop343
@gameworkshop343 2 жыл бұрын
I'm 14 and I got at ct200u ex minibike it's a Coleman and it has a 196cc clone I've put 18 pd valve springs I have go power sports stage 1 basically it a header exhaust and a bigger jet cause it comes with a bigger air box intake and I have a clear valve cover with a jack shaft and on the valve cover when I was Installing it the bottom right hole where u put it was stripped the bolt wasn't stripped the actual upper was stripped so I put some electrical tape on it and put the bolt in and it kinda worked its leaking a little bit so I'm looking for a upper head and I was looking at go power sports stage 3 head its milled I think.30 or 40 and it has ported and polished but if I get that will the rod break or the fly wheel cause I don't have either of them billet and if soo should I just buy billet rod and fly wheel or should I get a vm 24 maybe 26 or maybe a flat slide 24 maybe 26 idk what size ill get but that's the options??????
@connerdavis2450
@connerdavis2450 2 жыл бұрын
@@gameworkshop343 the head doesn’t affect Rpm, your throttle affects Rpm. But the head will add compression so it’ll gain Rpm better. If you don’t wanna hold it full throttle all the time you will need the bullet flywheel and billet rod. I would go with the VM 22 carb. I’m 15 nearly 16
@CrazyForCooCooPuffs
@CrazyForCooCooPuffs 3 жыл бұрын
Just ordered a pred 212 head from you, cant wait to get it.
@cliffpalermo
@cliffpalermo 3 жыл бұрын
Been waiting for a video like this!
@paulskartslifan4206
@paulskartslifan4206 3 жыл бұрын
Thanks , just had to get some time to make it. There are some more videos from a few years ago where I went thru some building tech videos. There is some good info in there. Some of it has evolved but lots of things to get the juices flowing. Paul
@spboyn9m280
@spboyn9m280 3 жыл бұрын
460
@cliffpalermo
@cliffpalermo 3 жыл бұрын
@@paulskartslifan4206 watched and learned for sure, like the flow bench videos especially
@paulskartslifan4206
@paulskartslifan4206 3 жыл бұрын
@@spboyn9m280 paulskarts.com
@paulskartslifan4206
@paulskartslifan4206 3 жыл бұрын
@@cliffpalermo I’m glad someone found a use force them 🤣✊✊✊
@delapenafishingtv5478
@delapenafishingtv5478 2 жыл бұрын
sir if u have 42 intake,,, what is the size of carburator we use???,, 42 also??? thanks
@paulskartslifan4206
@paulskartslifan4206 2 жыл бұрын
22mm Mikuni 😁
@delapenafishingtv5478
@delapenafishingtv5478 2 жыл бұрын
we can't use 42carburator 42intake and 38exhaust, 18hp for racing boat???
@paulskartslifan4206
@paulskartslifan4206 2 жыл бұрын
@@delapenafishingtv5478 I’m sure you will figure it out when you start spending the money
@skythekidrs
@skythekidrs 3 жыл бұрын
Hey Paul. I have a question about a fuel pump I hope you could answer. I recently hooked up a fuel pump to my 212 and it acts in a very odd way. When it’s not hooked up to the carb, everything works and it flows fuel out of the fuel out line. But when it is hooked up, it won’t flow at all and the fuel sits in the lines. If you could help me this I would be very appreciative. Also amazing video, heads look awesome 🔥
@paulskartslifan4206
@paulskartslifan4206 3 жыл бұрын
Not sure what that is. Seems like pressure
@GILSJOURNEY
@GILSJOURNEY 10 ай бұрын
What head and cam combo do you recommend if I am using a stock length arc rod and stock piston with a mikuni vm22 clone carb? And can you sell me a head, cam rocker, and rod combo? Thank you
@paulskartslifan4206
@paulskartslifan4206 10 ай бұрын
The carb will be the restriction. I’d recommend our trinity set. The set if bought comes with savings equivalent to $340 so it’s like getting the carb free and then some. Look into our trinity set. If you just want a head I’d recommend a smaller valve head like our 28/28 welded chamber head would be good on a 212. Compression ratio is hard to get on those and the welded chamber 28/28 is a monster
@GILSJOURNEY
@GILSJOURNEY 10 ай бұрын
@@paulskartslifan4206 thank you I am going to look it up.
@paulskartslifan4206
@paulskartslifan4206 10 ай бұрын
@@GILSJOURNEY www.paulskarts.com/product/the-trinity-head-camshaft-carb-14cc-big-valve-head-with-welded-intake-tube-and-epoxy-port-with-stainless-steel-valve-train-pkrpm3-camshaft-and-carburetor-option-of-gas-methanol-most-powerful-setup-you-can-buy-/464?cp=true&sa=false&sbp=false&q=false&category_id=2
@madness_-yg3lw
@madness_-yg3lw 3 жыл бұрын
Im very curious as to how one your heads would help my build iv got a predator 212cc non hemi head 63730 worked the short turns a little bit nothing aggressive just enough to take the sharp edges out of the head stock valves and retainers 18lb valve springs and 1.3 stamped ratio rockers stock style carb running .38 main jet with the mixture screw e3 plug and 1in trumpet style header (stage 1 kit) for bottom end stock piston stock arc size rod arc flywheel (pauls 212 hot coil with ground strap) and for cam a mod2 cheater cam it ran very good till i put the 1.3 ratio rockers i looks a couple hundred rpms before float but picked up a bunch of power on throughout the lower rpms. Is it possible by increasing lift of the valve instead of changing valve seat size i kept my velocity up but increased my cfm flow ?
@paulskartslifan4206
@paulskartslifan4206 3 жыл бұрын
Ask yourself how flow is measured on a flow bench and how they graph the flow chart. There in lies your answer.
@mikesbarn1858
@mikesbarn1858 3 жыл бұрын
Very educational.
@paulskartslifan4206
@paulskartslifan4206 3 жыл бұрын
✊✊✊
@markkonschak6288
@markkonschak6288 3 жыл бұрын
What are the highest velocity speed ratings you can get?
@paulskartslifan4206
@paulskartslifan4206 3 жыл бұрын
Highest you can get ? Well if you construct down the port to a straw size they will really spike up. But im sure you don’t mean highway you can get. Your probably wanting to know where you should be aiming for am I right ? 300-400 fps in high velocity areas is not hard to achieve. A good even 340 would be nice. Just trying to eliminate low velocity areas is a good place to start.
@markkonschak6288
@markkonschak6288 3 жыл бұрын
@@paulskartslifan4206 I guess what I’m asking is whats the highest average velocity are you getting in the body of the port.
@paulskartslifan4206
@paulskartslifan4206 3 жыл бұрын
@@markkonschak6288 that varies based on port size
@jamesferguson7137
@jamesferguson7137 Жыл бұрын
Hooked up backwards
@chuckhuff7123
@chuckhuff7123 9 ай бұрын
Why is dat?
@freedomforourfallen3755
@freedomforourfallen3755 Жыл бұрын
Hmmmmmm. That’s for making us slower guys understand
@willgachassin7031
@willgachassin7031 3 жыл бұрын
Gotta take a cashier's check nigga, if you can't you might not be legit
@paulskartslifan4206
@paulskartslifan4206 3 жыл бұрын
All orders are placed thru our website. Check to see if that’s an option to pay at checkout. Paul
PORTING YOUR PREDATOR FOR PURE POWER*
16:45
What Is The Wheel
Рет қаралды 40 М.
黑天使被操控了#short #angel #clown
00:40
Super Beauty team
Рет қаралды 61 МЛН
Beat Ronaldo, Win $1,000,000
22:45
MrBeast
Рет қаралды 158 МЛН
Chain Game Strong ⛓️
00:21
Anwar Jibawi
Рет қаралды 41 МЛН
Support each other🤝
00:31
ISSEI / いっせい
Рет қаралды 81 МЛН
We Dyno A Billet Head and Make Huge Power!!!
16:16
Red Beard's Garage
Рет қаралды 17 М.
Road to CNC 2JZ GE Part 1 : Porting and flow testing
17:07
HeadGames Motorworks
Рет қаралды 6 М.
14cc Head Port And Polish Plus Valve Train Geometry
46:43
DIY Willy
Рет қаралды 7 М.
CHEAP Predator 212 80mph+ Build!
14:48
JulDee MotorSports
Рет қаралды 74 М.
.308 Cam & Dual Valve Springs ~ The Road To Horsepower Ep 7
20:50
Red Beard's Garage
Рет қаралды 71 М.
Blending after CNC  porting!?
6:14
HeadGames Motorworks
Рет қаралды 6 М.
黑天使被操控了#short #angel #clown
00:40
Super Beauty team
Рет қаралды 61 МЛН