proform 585s treadmill problem starts then stops

[@sirgalahad4469]

I had same problem. I replaced a leaking capacitor on the motor control board and now runs perfectly! Cost me less than one dollar for the part.

[@maxxter07]

great job!

[@rallisoify]

If you have tested the motor with a fully charged drill battery and the motor moves normally, the only other possibility is the controller. The console is responding normally too. Try to get into calibration mode and calibrate the controller and incline motor. If you are unable to get in, replace the controller.

[@julioarredondo9341]

what do you mean calibrate the controller and incline mode????????

[@waheedzaman8706]

I had the same problem with one of the Treadmills, where the treadmill would stop after a short while. I started by checking all the parts and eventually reached to a conclusion that the problem was with speed sensor. Clean it, run it and enjoy...

[@Biorythym]

Yeah I'm having the same issue (proform crosswalk 397)...going to try and check it, but I don't knwo what a speed sensor looks like

[@nkay4693]

@@Biorythym speed sanser opp.moter balte near

[@ritacunningham7713]

@@nkay4693 where is the speed sensor located at

[@c21secco]

By the belt in the pulley wheel

[@ronaldbeasley7982]

I have the 405e e ProForm and the treadmill doctor said change the controller board I had the same symptoms well I still have them I'm waiting for my bored now to come through the mail

[@slomo535]

You can check thermal switch in motor with ohm meter. Mine has blue wires going to board - they need to be closed and will open when too hot. You can open motor and check winding crimps which often loosen. Also relay on board needs to close. Any burn marks on board? Bulging capacitors?

[@jasonkeuma1986]

Thanks for the tip. That was my problem. I’ve found reading the comments help As much as some videos. Thanks for the video too

[@williamleigh2586]

*This is the second Treadmill friend I've owned **bestgym.equipment** t was easy to assemble and easier to fold than my last one. The controls are a lot better as well. I give it 5 stars!*

[@houseofgodandgateofheaven]

I had the same problem get my garden blower and clean out everything Lined up speed sensor and turned it on and it works perfect.

[@josealvarez4130]

I have NordicTrack C2000 and when i push star button strip the breaker and stop

[@PhillyDee215]

My light indicator is blinking continuously while in operation and if I try to walk on it.....it automatically stops as if I'm to heavy(which is far from the case). Thanks 4 the video!!!

[@memorialparksundayleaguebr4013]

I have the same problem? So controller board? You mean the inferior circuit board Not the display board that superior or up stairs?

[@jamessimpson9690]

What if you notice a smell like electrical wires burning? I notice that smell after the speed of the treadmill drastically slowed and sped up again. I guess that's the motor burning up, going bad, or the circuit board? It's 5 years old, a Pro-form Performance 300.

[@23graduation]

Did you ever figure out what it was?

[@cooljazzr]

The motor just wore out. I bought a new treadmill.

[@anitacartmell6250]

I don’t know if this helps to zoom in on the problem but I didn’t have this problem until I removed the cover and used an air spray can to blow out the dust.

[@horstlauer5368]

Mine comes to a Stop if i lower the Speed less then 3 kmh.When i start d Machine again it doesnt works.I have to wait couple of hours,then it starts again.Above 4 kmh works proper.When it stops it says E1

[@johnatella8498]

Mine says it needs the pulse monitor - gives me an error message related to the pulse/heart monitor.

[@maxxter07]

hmmm, that sounds like something in the board on the console, not sure what exact part would be causing that, but you might want to check into a new board for the console? I would suggest contacting the following treadmill people to help with your problem: Century Treadmill Service Advisor 1-877-627-0349

[@checkitTV]

It’s the board. You can spend $200+ or you can buy MOSFET it cost $10 and replace it yourself

[@MohammedAli-yt3zm]

Same prblm with my tread mil plz guide me about this..after 35 min and above it is to be stop as i increas to speed high ..iand then i restart it is runing but as i do speed high so same prblm it is stopped...my tread mil name is olympia..it havet bought 32 month ..

[@arbaazkhan2878]

My treadmills left functions do not function, what could the problem be

[@draganakovacevic2143]

If it stops immediately after starting, the speed sensor is dirty, wipe it with some kind of wet cloth and it will work👍

[@fookutube501]

I got one of these ,brought it 4 years ago.Just last month it keep tripping my breaker in the house when i turn the switch on.So when i look into it ,i realize it was the 2 blue wire connect to the motor,does anyone know what the 2 blue wires are for??

[@mr.makeit4037]

Heat sensor switch. When the motor get hot, it opens the circuit and shuts the motor off to cool. You need that. Motor protection.

[@nls4290]

How do you fix this? I think I’m having the same problem

[@alecstone6674]

I'm having the same issue on the same treadmill.

[@sinisterhalloween4472]

I have the proform 430i treadmill that had a burn smell coming out of it for about a month, but still worked, until it started to stall no more than 17 seconds at 9.0 mph with the inside of motor sparking, then shutting off altogether. It restarts then hums loudly while running the belt at 4.0 mph. Treadmills are complicated machines.

[@dalesmith7777]

Hope ya got your machine squared away, I have a proform 1200 . Mine just started doing this..... Power on install magnetic key hit any speed it start and in less than a second it restart, the red light goes out the console power goes off the comes right back on. The Reed switch is property gapped at .125 ....has anyone heard of this. Oh when the motor cycles it takes off quick like it was set at 10mph. But quits in less than a second?

[@rynoholland-muter9660]

@@dalesmith7777 I have the exact same problem on my Nordictrack c100... the motor was blown and after replacing it it will switch of a second after restart... not sure how to test the board. Did you find thw problem to yours?

[@Chev7219]

I swore after the manufacture told me to plug my treadmill to the internet and upgrade their software mine started cutting off after 5 minutes. That’s their way to have people keep buying treadmills. Problem is way too common for too many. They should have improve technology the mechanics of treadmills since “parts” is common problem for all brand names.

[@nazarkareem83]

I have the same problem with the same model.

[@maxxter07]

Hi Fahad, Contact treadmill service advisor at 1 877 627 0349. I got my parts from them, and they have EXCELLENT tech support. My problem turned out to be the controller board. Marc

[@aanaroma]

Marc W ..any advisor from pakistan ???

[@aanaroma]

Marc W same problem occure when restart after use ... resisters are changed now but still problem occure

[@amrmakarem8556]

hi my treadmill work for 5 seconds then stop and show E03

[@nkay4693]

Chak you toub risrch eare

[@issacmelero9302]

Speed sensor. Thats usually a bad speed sensor or disconnected speed sensor.

[@robmolin4288]

Hi, did you find out what the issue was?? Thanks in advance...

[@maxxter07]

Hi, yes it was the controller board- replaced it and it 's running fine now...

[@pappydave1029]

@@maxxter07 Marc W. I am having the same problem with a Proform 580X. It looks like the control board is what you suggest and that runs from $80.00 to $180.00. The treadmill is 17 years old. I replaced the belt on it about 2 years ago. Is it worth fixing or should I invest in a new one? If it is worth fixing, where do you suggest I get my parts. I live in DFW area of Texas.

[@waynekimler6355]

@@maxxter07 thanks

[@DefaultName-jf5nd]

How much it cost the controller board?

[@ritacunningham7713]

How expensive was it to purchase the circuit board

[@maxxter07]

i dont recall- it's been a couple years ago....

[@waynekimler6355]

@@maxxter07 So it was a circuit board? I have the exact same issue, it starts then stops. Exact same treadmill too. any help would be grreat Im reading through your comments. Thanks

[@maxxter07]

@@waynekimler6355 Hey Wayne- yeah you can order the controller boar through Treadmill Service Advisor 1 877 627 0349...

[@sashacraig-taylor6208]

THIS SOUNDS LIKE THE SPEED SENSOR ON THE motor is not working.

[@jh1q6250]

What's up man did you ever figure out what was wrong with the treadmill

[@maxxter07]

Hey Jeremy, Yes, it was the controller board.

[@maxxter07]

Jeremy, I got some excellent tech help from an experienced treadmill technician when I bought my controller board. I can't remember the name of the actual company, but here is the email address of the tech, he can point you in the right direction if you are having problems- I highly recommend [e-mail]

[@jh1q6250]

Marc W appreciate that!!!

[@dianamatamoros5263]

Jeremy Hooter hi

[@waltetbrown6189]

@@maxxter07 hi Marc , when you say it was the controller bord , do you mean the top panel with the buttons or the circuit board at the bottom where the motor and power supply ? I have the epic tl1700

[@bobbear4437]

unplug the leads from your motor, if it shuts down then its the board

[@fatmael-kady7419]

I have a treadmill when I run on it after 13 min.it stops then I see the word Error 2 ..can you help me

[@hishamchohan494]

Fatma El-kady if you have the user manual read it.or when was the last time you lubricated the running belt with silicone spray

[@speakingtonganwiththetutuu8421]

I had the same problem play for 1 second and then stop mine is Nordictrack commercial 1500 need help

[@marcosantoyo4886]

Semisi Tutuu did you fix it because I got the same problem

[@marceloangon379]

what was the problem buddy i have same problem with my treadmill norditrack a 2105

[@marcosantoyo4886]

Marcelo Angon when I turned my treadmill on, the belt went fast then turned off

[@marceloangon379]

@@marcosantoyo4886 ok thank u

[@markbisbee5970]

What was the cause? Mine is doing the same thing?

[@maxxter07]

Hi Mark, The controller board was the issue. I replaced it and everything works fine now.. Hope his helps...

[@markbisbee5970]

Marc W thanks where can I order one?

[@maxxter07]

@@markbisbee5970 www.mc70repairexpert.com/

[@treadmillhacks]

Seem like you need a speed sensor

[@ritacunningham7713]

I have the Pro Form Crosswalk 397 treadmill it starts and then a minute or 3 the walking belt stops. The light is on the circuit board then once the belt starts the red light blinks continuously until it stops then light is solid. I tested the motor by using a DC battery and the walking belt continued to run and never stopped. Anyone have the same issue cause I am lost on how to fix it.

[@maxxter07]

yep, that was my exact problem- replacing the controller board was the solution...

[@maxxter07]

Contact treadmill service advisor at 1 877 627 0349

[@ritacunningham7713]

@@maxxter07 was thinking maybe one of the problems was I have not lubricated the treadmill since I owned it.

[@mojkav4849]

Hi! I have U style treadmill. After starting, it runs for 1 min then stop & display error E08. what to do to reset the computer or fix the problem? thanks SVAR

[@maxxter07]

Hi MOJ, Give Century treadmill a call, they got me going, and provided excellent customer service and support. My issue turned out to be the controller board, and sounds as though you may have the same issue. Century treadmill- 1-877-627-0349.

[@mojkav4849]

Hi Marc, Thanks, but I am in Norway. Du you know if they have e-mail I could send them a picture and explination.

[@ninjamantis8309]

i have the exact same issue

[@josepedraza2530]

I have a. 770ekg it runs for 5min and flips the breaker

[@aanaroma]

Facing the same problem when i restart my tradmil after use of 5 minute... please help me to fix this problem

[@hishamchohan494]

Fahad Fahim try to stArt it and unplug the power it might work

[@aanaroma]

I did ... but not working

[@hishamchohan494]

Fahad Fahim oky tell me the brand name.... model no. ......

[@maxxter07]

Hi Fahad, I cannot find the email address for Century Treadmill Service, they only list a phone# [phone]. I searched many times on the internet, but all I can find is a phone#. Here is a link I found to some of their services...www.mc70repairexpert.com/ hope this helps

[@rukmansiriwardana2273]

Hi my treadmill brand ni-track, when I plug the cable and try to turn on, it’s cuts the power off. In fact turns the breakers off. If anyone there please advice. Thanks

[@michaelbarrett3532]

Hi I have the same problem with a proform Treadmill, just wondering did you find out what was wrong ?

[@rukmansiriwardana2273]

Hi Michael, yes I found the problem. When I was open the bottom motor. Over full of dust. Use a brush and dust all areas. Then there was a sensor it has turn to wrong direction. I just turn to right direction she start to turn. All good now If that not work out, all the wires connectors you can clean with contact cleaner, then check part by parts electric connection to see the electric running to the controls.

[@rukmansiriwardana2273]

There was a video if I can find will attach here.

[@thomascarr2931]

Sounds like you need to take an air tank and blow the dust and lint out of the motor it is overheating there is an overheating sensor in the back of that motor

[@myownboss1318]

IRFP250N Transistor

[@aanaroma]

My Own Boss Is this only a transister problem

[@ypankiv]

Thank you My Own Boss. The transistor was fried with no resistance between any of the contacts. Replacing the transistor resolved the problem.

[@gerikuper6473]

Hello my problem is the all is working dcreen power but Both motor not working up down and belt motor not spinning i have check the motor with battery is working .

[@thomascarr2931]

I just watched a video of your problems and it is the sensor on your drive belt the motor is hooked to the little sensor is out of line I too close to the drive wheel

[@maxxter07]

Hi Thomas, One of the components on the controller board was bad- I replaced the controller board and that solved the problem.

[@logifinirator]

@@maxxter07 by "controller board" do you mean the upper console controller board or the lower controller board under the hood? Thanks!

[@maxxter07]

@@logifinirator Hi Casper- I meant the lower controller board under the hood...

[@dnicolas209]

Hello Marc where did you purchase the board for your fix I'm having the same issue and tested the motor with a battery good. Incline and panel all work good, appreciate the feedback 👍@Marc w

[@maxxter07]

@@dnicolas209 Hi, here is the link to the vendor where I got the controller board....kzbin.info?q=https%3A%2F%2Fwww.mc70repairexpert.com%2F&redir_token=QUFFLUhqbHJsNHQzQU14MEZ4X3RuNkF1VDh0eGFKNEV3Z3xBQ3Jtc0tuaUYtcU9JX1VQM2I1SzBUdlJQckNXMXNZWnRqUUZMd2VaUGxUdGtMMHZ2QnBYY09PR0NCUzNmeFZWU3hxdzgtbmdqcExRMmpuWlNMWE9WYlV6X0k0TVlIV1RabnpPdEFiak9hT3VwUkI4QmdyNVpIZw%3D%3D&event=comments&stzid=UgwZ4bF7oBXcgPxtYCZ4AaABAg.8oVgkPJ5uU48pCS1BnlnTd

[@JohnSmith-ve3ro]

I got a threadmill from someone- was working before I moved it. Now I have a similar problem - kzbin.info/www/bejne/q6jCf3ypnN6Ffbs Checked it with a battery and the motor/belt moves.

[@jrayborn78]

Same with me, I checked the treadmill before I purchased it by walking, inclining and increasing the speed. It seem like soon when I moved it from the place I purchased it to my place turned it on and walked for bout 13 seconds it stopped.

[@jrayborn78]

Note: James Rayborn is not the one making this post Chris Heard is I'm using his computer.

[@J_G0814]

@@jrayborn78did you ever get your treadmill fix and found what the issue was? Currently Having the same issue

[@ctmusic2465]

you speak at a low level use a good mic to do videos..

[@maxxter07]

you need to find your volume control- I have absolutely NO PROBLEM hearing it on my computer- actually it's pretty loud.