Programming a Marantec Remote Control

Programming procedure for a gate or garage door system using a Marantec Remote control
Buy from our website at www.gateremotes.co.uk or give us a call on 01302 700771

[@judithbeshel8696]

i bought this from garage stop and it said to watch the video if i don't have an existing remote. nope, not on here. garage stop has no customer service either. great.

[@rosaenriquez7155]

OMGOSH!!!!!!!!! THANK YOU SO MUCH! I bought a new remote over a month ago, but was too dumb to figure out how to transfer the code to the new transmitter. Your instructions are fool-proof!! NOW I understand the written instructions that came with the new device. The garage door opener and remote were already here, and I'd never had one. I can't believe how easy it was. Even for me. Thanks again! 😊

[@Jjhuh]

Although this video didn’t directly help me with my remote problem, I still found this video informative. Thank you very much.

[@thomasbarronsampson9084]

Thank you for not having loud music in your video!

[@tanyaczarnecki3074]

Thank you for being the only video specific in the fact that the buttons MUST MUST be released at the same time. Your video allowed me to be able to program 4 remotes!! Thank you!!

[@eileenplowright-hallplowri146]

Absolutely correct information from experts. I managed to programme box in garage and then do rest with brooch! Thank you very much!

[@mattcero1]

I have no working remotes, they were all lost. Now I have one brand new remote and need to get it talking to my Marantec garage door opener. How do I do that? Thank you.

[@gymratt88]

Two years and no reply...

[@kpw1952]

The new coupler for these remotes has much longer pins than the old one. Do not push it all the way in like the video says. Only put it in about a 1/4 inch. Otherwise it will hit the battery short out and will not send the code. It only took me 3 hours to figure it out. Oh well it works good now.

[@ngcalderon08]

kenneth woodman thank you so much! It worked and only took me 10 min because of your comment! When I was pushing all the way in it wasn’t working. I had the old remote as the one with the original code.

[@alisonmacsal]

Did this and it worked straight away and saved me a lot of tine! Thank you for your help Kenneth

[@biden_lost4205]

YOU SIR….. Saved. My. Ass. Thank you

[@mrdang910]

Thank you for this comment it worked!!!

[@Tronous117]

Commenting to bump this comment up. All I got was a solid red light until I pull out the pins a bit from the new remote.

[@Joshespi]

exactly what i needed, thank you!

[@-smp-scientificmethodpersp838]

I bought an off brand pin to do this, and it didn't push in all the way (because I couldn't), like in the video, but it still worked. Just a heads up for those of you who don't have the same pin as the guy in this video.

[@thanh-liemle7704]

Thank you for sharing this.

[@georgesmathers6056]

Works! Thanks a ton.

[@itsanna123]

I have found it necessary to bend the remotes backwards slightly while they are plugged into each other, in order for the inner contacts to meet. With the connected remotes facing me, I bend both remotes away from me through an angle of just a couple of degrees each. It is not enough pressure to put a permanent bend into the connecting pins, but just enough so that I can feel the springback tendency of the connecting pins. Holding the remotes in this position, I proceed with the transfer as directed by the video. I learned this bending step from another video here, but it was in a foreign language.

[@fandiwang3845]

This literally saved me, thank you!!!

[@aaronclausen654]

Thanks saved me too

[@groggysword33]

You’re a life saver. Was trying over and over again to make them work!

[@patrickarseneault7407]

nothing worked till i tried that. thank you

[@thanh-liemle7704]

You are Godsend, this comment helped me a LOTS. Thank you!

[@morganjarman5621]

Yes, thank you!!!

[@aramnagle]

I don't have a working remote, how do I sync it with the lift?

[@tanyaczarnecki3074]

kzbin.info/www/bejne/q5mVlp-nqbCciqM here's how I got started, then used his video to sync our other remotes.

[@AndrewMuse]

Same question

[@geoffmurray4362]

As with Kenneth Woodman below we found the connecter didn't work fully pushed in to the new remote as it had longer pins so I did what he said and pulled it out slightly. Hey presto it paired OK then. Despair was setting in.

[@gailm67]

where can I buy the pin plug? I have 2 remote controles but no pin plug and want to pair them!!!

[@MSPA2006]

My program connector tongs are longer and I cannot push the connector into the transmitter allowing the black plastic on the connector to stop against the transmitter. I tried programming and the receiving transmitter light doesn’t flash or pick up the code from the sending transmitter.

[@szamizdat]

How can I program a 4-button Marantec Digital 302 using a 2-button of the same type? The method presented in the video doesn't work. (I want to program the lower button of the 4-channel transmitter, using the 1st button of the "old" transmitter. The new transmitter LED doesn't start flashing, but lights constantly.)

[@jahusk]

Marantec without remote

[@davidbrucemusicvideo]

I haven't seen one video on the Internet on how to program a brand-new one of these if you don't have an old one because it was lost. Is there any information on how to program a new one alone?

[@geraldmccolgan7395]

Any luck, I'm in the same position?

[@PatrickStephensTheHucklebuck]

Yea ...What the fuck

[@tracylandrum4014]

Me too!

[@ShortJourneys702]

Same here

[@Tunechi65]

Any luck yet lmao

[@lyhungpham4388]

Hello. Where can i buy the brooch ?

[@slapppshottt3239]

what a real name of pin plug on your website i want buy one

[@saltlakecityhousingmarkets5879]

Seriously.... I don't have a working remote... that's why I got yours.... Seriously...