Project Raging Rhino: Yamaha Rhino 700 Tear Down Part 1

Time to dig in to the 09 Rhino 700 and see if we cant get that 8500+mile engine out and ready for tear down!
Support AMR with official merch! Check it out: teespring.com/...
Support my channel by becoming a Patron and get access to Patreon exclusive content including live hangouts, give a ways, and Patreon exclusive videos:
/ appalachianmountainriders
Check out my Amazon Influencers page were all the tools, maintenance items, accessories, and even the camera gear I use that I've bought from Amazon are available all in one place. Buying items I have listed here helps support my channel too! www.amazon.com...
Support my channel when you can with no commitment:
paypal.me/keep...
Join the Riders on
facebook: / appalachianmountainriders
Instagram: / appalachianmountainriders
Some of the links above may be affiliate links that I receive a small commission from. This helps support my channel and enables me to continue to make enjoyable quality content.

[@jasond1245]

Really looking forward too this build I like different builds tired of the the can am and polaris stuff that other KZbinrs do.

[@AppalachianMountainRiders]

Wait till you see what I have coming in the mail for the Pioneer 500! Going to be a P5 first!

[@jasond1245]

@@AppalachianMountainRiders nice I'm Honda guy after all

[@scottygunter6644]

Im doing the same thing to my commander rite now . I tell ya that is a chore all in its own man , good job and keep up the great work !

[@AppalachianMountainRiders]

Just for general maintenance or are you doing a build too?

[@scottygunter6644]

@@AppalachianMountainRiders I threw a rod bearing and it was catastrophic failure all over the place .

[@AppalachianMountainRiders]

Yikes! Hope all goes well and you get it up and running again quickly!

[@scottygunter6644]

@@AppalachianMountainRiders Thanks jason .👍

[@oneeyedrone4293]

Very good info, I have a top end clicking noise on mine so im going to pull the motor this summer to replace the rod / crank as a precaution (she has about 4000 miles) and had a high rev ignition box that I think oil starved it and she thumps really loud now at times. Struggles to start but will stay running. valves all checked and in spec, so it has to be the rod being slightly loose, sounds like piston slap but just doesnt go away sadly even warmed up.

[@Bill14886]

Very nice, definitely interesting video. Cant wait to watch the rest as you continue on. I have a 03 650 Prairie that's needs rebuilding. Summer time job. Hope its rebuildable.

[@GunsNReloads]

Good video! I liked your editing doing the fluids!

[@troynoall793]

Did you remember the spring that was inside the rear shaft? I missed seeing that part of the video... Great work...

[@AppalachianMountainRiders]

I did! It’s safe on the work bench.

[@bwyyy7306]

Belts last forever on yamahas

[@jasond1245]

I'm not cvt fan but Yamaha does it right with a wet clutch design

[@ramsayhenderson7331]

Hey have a question for you. I’ve got an 09 rhino 700. Reverse works phenomenally in neutral Atreves perfectly pray but when I put it into gear to move forward the motor just shuts off

[@zachellinger6574]

“People’s Eyebrow” ftw

[@AppalachianMountainRiders]

Zach Ellinger 😂😂😂😂

[@davevanbuskirk5455]

I have a 07 700 Hisun 4x4 runs and drives like it's should starts up ever time has lots of power but my problem is that it started putting water in the oil and oil in the water so I changed the water pump and seal and oil filter and ever thing new into it stared it and drove it 2 miles around my field then back to my house and checked it to make sure everything is fixed and working like it should and it was just like before I put the new oil pump and seal on it what could it be any info would be great I got a hole top end gasket kit for it and before I do that big job I wanted to see if it could be anything other then that don't want to do all that work if it ends up being soling different

[@AppalachianMountainRiders]

I would say it’s a safe bet that your head gasket is blown. That’s the most logical way for the two to be mixing like that and most likely the cause.

[@davevanbuskirk5455]

Ok thank u I got the 2 new gaskets for it not going to put the new ones on thanks for getting back to me I going to be making my own video rebuild of my hisun700 I have a video on here now on my utv and what its doing if u look on my page then u can see the one I have and what its doing

[@johnsonoutdoors8117]

Zippy?

[@AppalachianMountainRiders]

Patiently in storage waiting for me to find a good deal on fender plastics. I’ll be getting it back out this spring to finish up a few odds and ends left to do.

[@johnsonoutdoors8117]

@@AppalachianMountainRiders if you find two good deals tell me one of them most are for 200 dollars that I can find

[@AppalachianMountainRiders]

Johnson Gaming that’s the prices I’ve seen too. I just keep an eye out for some used plastics in better shape than my old ones. Hoping I find some!🤞

[@johnsonoutdoors8117]

@@AppalachianMountainRiders how much do you want for the old front plastics don't need gas tank cover