OM617 to Toyota Adapter Plate Installation

[@cooda069]

you should make one for VG transmission or VQ

[@Millin21]

Would that adapter plate fit an OM616??? It would go to a 5-speed toyota manual trans. Same question for your engine mounts......

[@Millin21]

Joe Peterson yes, its the 2.4 L

[@timgardner9965]

Hey Joe I need a adapter plate for a 2004 nissan xterra is that something you think you could make it will mount to a om617

[@timgardner9965]

I have an auto trans in mine but I want to do a 5 speed manual swap I will find out what it is and let you know

[@papadizastr]

Do you have the adapter for a 617 to 94 Land Rover discovery zf transmissions?

[@midgrave]

so where will the pilot bearing go? wont the extra distance of the adapter make it impossible to use a pilot bearing?

[@midgrave]

Im still unsure how the imput shaft will reach into the pilot bearing if you put a spacer between the gearbox and engine?@@doomsdaydiesel

[@offgridmangogrower]

Are your flywheels the same mass or weight as stock?

[@doomsdaydiesel]

They are stock

[@edwardhawran9406]

Isn't the OM617 an externally balanced engine? Would you comment on a good way to preserve the original flywheel or flexplate's balance characteristic in the new flywheel?

[@doomsdaydiesel]

The entire rotating assembly is balanced as a whole. You must mark the flexplate before removal and have your new flexplate or flywheel match-balanced. Of course, that is many times not necessary as the stock flexplate is usually very close to neutral balanced.

[@AbrahamPIT99]

Que tipo de clutch y fly wheel se le pone el de toyota 22r o el de mercedes benz ??.Gracias

[@shanecall]

El flywheel es de Toyota, pero modificada. El clutch es la de Toyota sin modificaciones.

[@moreofjosem5363]

Le ordenas el flywheel en el sitio del señor y se une a un clutch de 22re preferable k sea stage 2 o mas fuerte k ese por k va a tener lo doble de torque que el motor original

[@jcreichle26]

whats the weight of the redrilled flywheel? i run a manual trans in my mercedes 300td, and the factory flywheel is 38lbs, figured with a lighter one it might shake a bit more. just thought id ask, hunting another om617 for my 4runner

[@offgridmangogrower]

Have you repowered one of your toy’s yet….if so how does it feel with the extra torque?

[@mb1088147]

Looking to buy this kit for a 2wd version, would this kit work with a w58 trans??

[@doomsdaydiesel]

Any W series bellhousing can be swapped amongst W-series trannies. You'll have to do the research on input shaft length and throwout bearing, but you could run a W56 or W59 bellhousing. Starter is on right side for W56 and left side for W59.

[@mb1088147]

Doomsday Diesel thanks man

[@kevinestes7358]

Flywheel weight?

[@freddurst7181]

How in the world are u gettin that thing to shut off u running vacum to it

[@doomsdaydiesel]

Check out the wiring video. It uses a Toyota EGR solenoid and the CIG fuse power.

[@freddurst7181]

@@doomsdaydiesel ok working on a jeep.someone built and it had a vacum silinoid on it but stopped working can figure it out i can get it to shut off but won't start back unless u unhook vacum like to injection pump like its holding vacum

[@freddurst7181]

@@doomsdaydiesel ill.try that thanks man appreciate you

[@AbrahamPIT99]

Muchas gracias 👍🏻

[@danielclaggett6110]

How much is the adapter kit? Where do I get it??

[@AbrahamPIT99]

Que tipo de clutch y fly wheel se le pone el de toyota 22r o el de mercedes benz ?? Gracias

[@ReelCatcheeeHi]

@@doomsdaydiesel I go on the link but nothing shows up on it on how to order a kit

[@moreofjosem5363]

Ab tijerina si dice k un clutch de una 22re funciona

[@pinzgauernorcal]

hello DD, what year/model toyota, is a good choice?

[@doomsdaydiesel]

1984 & 1985 are easiest with factory steering. Otherwise, 86-95 are also great choices.