Quick EGR Fix | Sticking EGR | Ford Figo Fiesta 1.4 TDCi

[@liamwaterworth923]

thank you so much for this video, I have just fixed my car and now drives better than ever.

[@dailyhandsdiy]

Glad to hear from you mate 😊

[@sashankraghupatruni4523]

Amazing! The way you work is so clean and tidy! brother please make a video on ford figo/aspire clutch and brake bleeding if possible!! your Diy stuff is saving our money man!! Great job buddy!! keep inspiring people!! God bless you brother!! thankyou so very much for making us understand in simple way, man this stuff is so helpfull.. must subscribe!!

[@dailyhandsdiy]

Made my day bro. will surely do the bleeding soon. :D

[@sashankraghupatruni4523]

@@dailyhandsdiy ❤

[@fayizct8039]

Keep on posting anout ford tdci works... Keep it up good video

[@dailyhandsdiy]

Sure and thank you. :D

[@jmarks7419]

I have a 2008 Fusion 1.4tdci. Will start and tick over fine but as soon as i drop the clutch and put load on the engine just cuts out. If i was just to drop the clutch at Idle the car will drive and would drive all day. I can hold the revs at 1500 but as soon as I put accelerator down the engine cuts out. I have replaced the fuel filter, changed the priming ball and fuel pipes, cleaned the tank and sender unit (all OK) even tried different diesel from a different garage just in case but still the same. Do you think the EGR would be causing this problem. As a side note injector 2 and 3 were also replaced 2 1st and then 3 went straight after 2, car is definitely running on all 4. MAF was also cleaned.

[@dailyhandsdiy]

Bro hve you checked the crank shaft position sensor?

[@jmarks7419]

@@dailyhandsdiy no - do you think it could be it, what does it control?

[@dailyhandsdiy]

Its a symptom and chance, it pickups engine timing from flywheel. And also pedal position sensor is also a chance.

[@abilashab5347]

Hi... Iam from kerala i have a ford fiesta diesel 2011 model. My car is not getting enough power while giving acceleration what will be the issue, thevgarage people already reaplaced the turbocharger...

[@dailyhandsdiy]

Hi bro, firstly check and clean maf sensor, secondly check if theres any loose clamps after turbo, 3rd if egr is not functioning well. Does your car give any error codes on dash?

[@yasirsalman88]

Good info bro. Next make a video on inlet manifold cleaning

[@dailyhandsdiy]

sure bro 👍

[@sreerama4616]

Bro your videos are spoon feeding to us. Thanks bro...

[@dailyhandsdiy]

Most satisfying support ever bro. Alwys welcome. :D

[@nigelmiddleton2727]

Great video mate 👍I am just about to do that job on my fusion and that video certainly helps.

[@dailyhandsdiy]

Thanks mate ;)

[@ramkarthikp1983]

@@dailyhandsdiy sir where you are staying. i want my egr to be cleaned

[@kuttusooraj1]

Hi, Is it ok to use normal WD40 as penitrant for EGR cleaning in place of HIT?

[@dailyhandsdiy]

yep that will do fine...

[@1danny2k]

Blanking plate mod will work on figo or will ecu throw a code?

[@amitdesai2421]

We are having problem with our customer's fiesta (same 1.4), engine stalls while running sometime. Dtc shows p1412, I'm just thinking that if egr get stuck can engine stall...?

[@sai00079]

Did you get solution for that, can you please explain me on that

[@amitdesai2421]

@@sai00079 We cleaned egr, problem solved...!

[@sai00079]

Hi bro thanks for your response, can you please give your contact number I need solution for this please help me 😢

[@kishangalibaku6048]

Good day sir, Im glad to come across your channel I appreciate the time you take to deal with all of these our questions Truly, you are patient and humble. I do have a ford figo 2015 model 1.4 tdci, i have been driving in limp mode for more than a month now Limited power also and jerking sometimes Could you please help what to check on this one also I will truly appreciate your feedback Thanks

[@dailyhandsdiy]

Hi...there, glad to hear bro...is there a malfunction light flashing, a gear symbol with exclamation mark.?

[@kishangalibaku6048]

Good day sir, Oh yes, the symbol flashes 24/7 non-stop Sorry for replying only now sir.

[@dailyhandsdiy]

Ah yes it means either the fuel system mainly the injector or the glow plug has an issue. Mostly if there's jerking, injector is the one. Could just scan the ecm for fault codes.

[@kishangalibaku6048]

Haven't scanned yet but I'm planning to do so soon. But injectors were once removed and nozzle holes of all injectors were open as the only test done on injectors was to open them 😢and check for nozzles blockage And all nozzles holes were free

[@dailyhandsdiy]

Its not the nozzle holes, its the injector actuator or could be the fuel pressure regulator..

[@SuperLinas123]

Hi, i have a code P0490 on my car mazda 2 1.4tdi 2008, cleaned egr valve and cooler, but still then pushing full accelerator car starts jerking, vacuum hoses checked all good. Any suggestions where could be a problem? I would be very appreciate for your answer

[@dailyhandsdiy]

Hi, do check the wiring and connector for corrosion. Check the continuity of wires from ecm. Worst a damaged egr motor or internal shorts.

[@akhineshnathnairs9302]

Hi bro my car is ford figo 2014 1.4 tdci model when i checked the turbo to intake manifold hose there is a slight oil leak but the turbo shaft play is normal and vehicle acceleration is also quicker but there is a black smoke not too much after 3500 rpm on first gear and third gear driving

[@dailyhandsdiy]

Black smoke after 2500 rpm is quite ok for any ford tdci engines...

[@tmautos-surrey-sussex]

Thanks for great video and explanation-had a fiesta with really rough running engine light on crawling at 2mph - did exactly what you did found mine didn’t have a remove plastic circle mine was metal sleeve that couldn’t be removed but could be turned , the valve was sooted up and solid- so penetrating fluid and patience got it free again and refitted customer now very happy - cheers

[@dailyhandsdiy]

Cheers mate .and .glad to hear from you.

[@sydneyramulifho89]

good day, where does "fuel volume regulator control circuit range / perfomance sensor situated on a ford figo tdci 1.4, i will be glad if you can send me a picture of it. thank you

[@dailyhandsdiy]

Hey there, its actually Situated on the fuel high pressure pump. Like a long small cylinder with a connector ath the end.

[@vinodpednekar6835]

Awesome job...keep us educating, thanks lots for your great effort..

[@dailyhandsdiy]

Always welcome :)

[@PavanKumarRavinuthala]

Hi Bro, I went to the mechanic and cleaned the EGR. Even after cleaning EGR there's black smoke. The car feels sluggish when AC is on. Once the turbo kicks in, it accelerates fine. I've tried cleaning the MAF Sensor too, is the black smoke due to MAF or its the already deposited soot in Exhaust coming out ?

[@dailyhandsdiy]

Hi bro.. cannot say that. it should be the egr itself. Try disconnecting the egr connector and drive. See if it improves.

[@Thanos-ic8ki]

I would also suggest going on a trip long and driving the car fast for a long period at around 3.5k Rpm so any soot build up would burn away from the catalytic convector and other parts of exhausts ofc please do it safely and in 5 gear on a long stretch of highway driving around in city bumper o bumper traffic can do this to your car you will feel a lot of black smoke come out but after a few seconds it will stop but keep going till it stops and Ofc the car should be properly warmed before you perform this and should have new oil changed recently for minimal damage bigger engines have regenerating cycles which do the same thing the settings are called DPF regeneration.

[@vishnupkumar5357]

Hello my friend, I have the same issue of black smoke on my figo even after cleaning egr,MAF sensor and catalytic converter. Cleaned it by removing Egr and catalytic converter..what may be the issue??

[@piecetoyou8285]

Nice and simple to follow, Nice clean footage thank you, Does this EGR have a diaphragm where the plugged part at the bottom has been sealed,or in the top part where the electrics are, iF it does how would I know if diaphragm is no longer functional,?

[@dailyhandsdiy]

Hi there, this is an electronic type valve and does not have a diaphragm. But the old tdci engines came with a diaphragm type valve with a control Solenoid. To check that need a dismantle and should check with a suction pump and create a vacuum. Look if it stays or has no response. Now if you are asking about the newer tdci engines with a vacuum bypass valve(small black thing with an arm of like 3 inches). Ask some one to keep an eye on the arm when the car is started. When cold started, the arm should move in completely. if it does nothin, check the vacuum hose for leaks.if no leaks and gets a strong suction from pipe,the diaphram is damaged.

[@piecetoyou8285]

@@dailyhandsdiy Nope same one as yours, but cheers for quick respons and info on other types very helpful, My ford fiesta sport 1.4 tdci 2008 5 door hatch, driving at 60mph, started to judder,the more gas i gave it, the more it would jult and slow down. So I dropped the gear give more gas and it just kept pulling back untill going about 10mph,went into limp mode, injector 3 on rail came up on the scanner, injector three compleately blocked,removed all injectors removed the bottoms` cleaned and torque them all back up, also return fule line was blocked, The car had been juddering off and on over the months but could go into limp mode if I started on a hill sometimes if i gave it to much gas,, so cleaned injectors as described up above they are siemens vdo dont know if they are the siemens piezo type, cleaned EGR cleaned MAF new air filter, new return fuel line from injectors, Might replace fuel filter don`t know yet, Ive reamed the ports of the injectors and new washers, I tested ohms and earth on injectors but can`t do a intermitten test on them, Tested glow plugs they are all good, My question is befor I put it all back together do you think the injector was the issue or EGR or some think else, Ps I aint a machanic ime just a give it a go I can`t understand my scanner correctly all i can do is wipe off codes,

[@dailyhandsdiy]

Should check the sensor part in the injector, if its 1.4 then surely its piezo. If the code reads short open or short closed on any injector, its a actuator fault, power gets lowerd and rpm restricted to 1500 and 2000 at no loads. Should clear the injector part first.

[@piecetoyou8285]

@@dailyhandsdiy The injector has a leak off connection opposite the inlet fuel line , the top of the injector `the black part is smooth, its shaped like a ducks head with pins hidden in the beak part,lol,no hole at top, all i know is it just says siemens vdo,on the side,everything else on top of the black part has rubbed away., How can I check the sensor part,what do you mean I only have a muiltimeter and a victor 60D? Do you mean if the injector was left stuck open or stuck closed then something in the injector called the actuator is playing up or the way the injector works there`s something wrong it can`t actuate lol,or the injector comen rail somthing wrong sending the signal to injector' Don`t forget I aint a machanic, I do know if its a piezo then pressure reacts the piezo`s by squeezing them ,Then that causes a voltage then that voltage rapidly send message back to ecu in milli secons and while this goes on the needle part lifts up due to fuel pressure ,Well some thing like that HA. when the car come to a halt I cleared codes then taken negative lead off 10 minutes after connected negative lead back; drove for 20minutes at 30,40 mph got me back home, Next day drove to pick daughter 10 minutes down road and it went to limp mode,taken negative lead off ,then placed back on` drove for 1 minute back to limp mode ,carried on driving for 10 seconds` then other symble poped up saying warning sign something like engine managment ,i pulled over car would not move,so I rigged up the code thing got rid of codes ,but engine synbles came back up, next day brake down service came turned engine over ,engine shaking he said injector must be not working,turned enging off got his car ramp device out got back in my car and turned engine on and engine sounded fine, he got his phone scanner thing and said theres no codes to read, so i said just get it up on your ramp and take it home ,

[@dailyhandsdiy]

Haha some correct some wrong. Piezo injectors are much complex in operatn,it sends the signal according to our power demands to injector peizo ceramic inside which expands n hits the injection head which activates n pulls back the nozzle needle causing injection. Now a small change in feedback or a problem with peizo crystal can male this fault. Need an insulation tester set to 60v or 100v and check the resistance btwn the injector connector pins. should be btwen 198kohms to 205 kohms. Also the capasitance btwn the pins should be abv 3mf. its a good idea to get the 3rd injector serviced.

[@Chakrimelodies]

Hi sir is it normal for fiesta diseal 1.4 tdci coming black smoke after 3k rpm?

[@dailyhandsdiy]

Yes thats normal.

[@Chakrimelodies]

@@dailyhandsdiy Turbo right side compressor wheel had not to much play and I saw little bit of oil on the Turbo compressor wheel when I press hard acceleration getting crazy of black smoke coming on the exhaust sir please tell me the Problem I'm goona fix that issue...

[@dailyhandsdiy]

A bit of oil is normal as its from pcv system... there will be oil, cant eliminate that. ford does smoke after 2.5k rpm...its gives out hell of smoke. Dont worry...if there's not much oil consumption and fuel economy is good..then its ok.

[@Chakrimelodies]

@@dailyhandsdiy Tq Sir

[@wadekruger6248]

Please make a video of replacing injector seals

[@dailyhandsdiy]

Sure will do.

[@madhureddy6899]

Hi bro Could please suggest a tool kit for car servicing. I am interested in doing my car service at home. Thanks

[@dailyhandsdiy]

Hi there bro, you need a basic 46 piece half inch tool set for basic needs. For figo, need a 21mm wrench for oip drain and 27 mm socket and an extension for oil filter cover.

[@madhureddy6899]

@@dailyhandsdiy I own fiesta classic, do we need to purchase 21mm wrench and 27mm socket separately or those included in 1/2 inch set?

[@dailyhandsdiy]

Sry i meant 1/4 inch set. 21 n 27 socket n extension should be half inch and needs to be bought seperately.

[@madhureddy6899]

@@dailyhandsdiy Hi bro Could please share me the link of useful tool kit for bike and car .. thanks

[@dailyhandsdiy]

Bro just search for 46 piece half inch tool kit. Can go for stanley or taparia.

[@anjosebenoy7295]

Does egr causes in not moving vehicle after accelerating and also a lot smoke is coming out. But vehicle is moving slightly after accelerates but not possible to drive like that. Pls Rply

[@anjosebenoy7295]

Will it solve by cleaning egr???

[@dailyhandsdiy]

If egr is stuck at open position, vehicle won't accelerate. youil see huge smoke. If its the egr, will solve by cleaning.

[@anjosebenoy7295]

@@dailyhandsdiy I check the egr. It has high resistance. It want to be clean Thanks

[@dailyhandsdiy]

Sure anytime.

[@Ben-bu2jg]

Hey pal, I’ve just had a power train light on and the car went into limp mode. Eventually I started it and it didn’t go into limp mode but was still a bit jerky. I’m wondering if a open EGR would cause this or as my theory is that a sensor has got wet and it’s poured down today and I went through some pretty big puddles. Your help would be appreciated. Thanks

[@dailyhandsdiy]

70% comes from egr malfunction and rest could be any thing like clogged maf. Seems not from a wet sensor i guess like you said.

[@Ben-bu2jg]

@@dailyhandsdiy thanks for getting back to me. These EGR valves seem nothing but trouble

[@dailyhandsdiy]

Tru bro its a hustle. particularly valeo rotary one, small carbon soot can make it work bad.

[@Ben-bu2jg]

@@dailyhandsdiy nightmare, my mistake was not cleaning the second hand one I put on so I’m gonna follow this video over Christmas and clean it and hope for the best. So thank you for making the video in the first place

[@dailyhandsdiy]

@@Ben-bu2jg Alwys welcome brother

[@micirei]

Hey, how much much would it cost to get the egr valve cleaned by a professional? I'm thinking about doing the job myself but I'm afraid I might just ruin it all.

[@dailyhandsdiy]

There's nothin to get ruined,just the bolts carefully not breaking them. From a mechanic it cost around 3 hrs or more hours of labour chrge depending where you live. Mostly btwn 1.5k to 3k inr

[@vijayendranvijay4538]

@@dailyhandsdiy even if there are no problems, can we go ahead with egr cleaning? Does it have noticeable difference? Can we do it with ford or any other outside workshops? Coz I want to clean only maf sensor and egr... Not sure if Ford service centres will do only these two things.. Your suggestion pls

[@dailyhandsdiy]

Im not sure if ford clean maf but will do the egr for sure. If you have a skilled outside mechanic, obviously outside is best. Its actually done as a preventive measure.

[@vijayendranvijay4538]

@@dailyhandsdiy okay sure bro.. Thanks.. U are doing such a great job..I wish u were in chennai.. BTW, when I go for service, can I tell them to check if there are any fault codes using obd2 scanner though I don't see any major engine related symbols in dashboard? Any harm in scanning everytime? If there are even minor problems, does the obd scan it correctly?

[@dailyhandsdiy]

Thanks bro...yes you may ask to scan the codes any numbr of times you want. Infact after cleaning maf n egr,whole system is scanned for problems so no wrys.

[@xdude361]

hii i cleaned the egr as you mentioned in the video...but after mantling i found a connector unplugged next to the egr connector...a yellow connector .,,its seen unplugged in your video too...wher to plug it/

[@dailyhandsdiy]

One blu and one green ryt. The blue one goes to connector behind the fuel filter and the green goes below the filter. There are two sensors in fuel filter. One one back one on bottom.

[@xdude361]

@@dailyhandsdiy apo eni veendum elakki paniyendi varum... car start aayi but off chayitapo oru beep keetu

[@dailyhandsdiy]

green wire ittillengil engine hiccups varum. raw fuel temp measure cheyyunnath anu green connctr circuit, blu for sensing water in fuel. Blue wire filter edukkathe vekkan pattum. ichiri tricky anu. green conctr filternte thazhe olla air hose elakkiyal pidipikkam. ath oru ichiri tricky anu.

[@xdude361]

@@dailyhandsdiy kure try chayitu... eni filter onnude elakkam... one more thing, i noticed some oil like substance around first injector... leak aayirikkumo?? Egane conform chayan pattum??

[@dailyhandsdiy]

Oil alla fuel avum. leaf off return pipe or connectr leak ayath avum. can u send me a pic. at 9747932260 whatsapp

[@Andy-mp8zr]

Hey, in the space of a year I've had a nightmare with engine management light coming on and reducing power in my 2012 fiesta. When I get the car checked out it always comes up with an issue with the egr valve. I've had 3 egr valves fitted in the space of the year and each time I've been told there was nothing wrong with the previous valve. Luckily 2 different warrantys covered 2 of these fixes. However the issue still comes up with every egr valve I have had fitted. Any idea why I still get engine management light related to the valve, when there isn't a problem with the valve?

[@dailyhandsdiy]

Yea, this could be a fault in ecm software. If the many egr does the same faulty thing, either its a fault in wiring or the ecm is not commanding it what to do but the feedback circuit is working, thats why u get an error code. Whats the error code its throwing?

[@Andy-mp8zr]

@@dailyhandsdiy thanks. The error code that comes up is the engine malfunction. And every time its diagnosed on the computer it says its the egr valve causing it

[@dailyhandsdiy]

Its a good idea to check the wiring and its continuity to ecm. a broken insulation, oxidised joints etc.. can also trigger this problem

[@Andy-mp8zr]

@@dailyhandsdiy thanks a lot. I'll get this checked

[@dailyhandsdiy]

Sure and any time brother.

[@sureshmallavarapu8204]

Can you please share a video for PCV Valve cleaning..

[@dailyhandsdiy]

hey bro in diesel engine there is no valve its a smal diaphram setup but unlike in petrols it won't clogg up.

[@sureshmallavarapu8204]

@@dailyhandsdiy mine leaking oil around the intake area(Small Pipe divided from the turbo and joining at the top of engine.. Please suggest

[@dailyhandsdiy]

Jst put a clamp on pipe bro, its usual... that portn which connects the topof engine will come loose and oil vapour pushes out. Jst clamp that side.

[@sureshmallavarapu8204]

Thank you very much bro... ✌️

[@dailyhandsdiy]

Any time bro...

[@madhureddy6899]

Hi bro, Removing the EGR connection and running the car will cause any harm to the engine? I am planning to run my car without egr connection any issues in the long run.

[@dailyhandsdiy]

No issues,engine will run clean.

[@madhureddy6899]

@@dailyhandsdiy just we need to unplug the socket right?

[@dailyhandsdiy]

Yup just unplug it.

[@ramyat1418]

Hi, bro my figo engine get stops at small speed breaker or a ditch if i go 30 or 40 speed without applying breaks,i have visited local mechanics but not resolved,what it could be can u advice on this.

[@dailyhandsdiy]

get stops means engine turning off? And at which rpm does this usually happens?

[@ramyat1418]

@@dailyhandsdiy i did not check rpm but every small blind ditch it get stops whether am in 80 speed or in 30, again i have to immediate start with the flip of key and little feared if won't starts at 50 to 80 speed, i feel could be a wiring or loose fuse, thanks for ur early reply.

[@dailyhandsdiy]

itz doesn't feel like fuse blown issue. Could be faulty relay which stops functioning at intervals. Also might be loose. or even loose drive train wiring harness. or could be a engine timing pickup problem by crank sensor. which also could be a wiring issue. So check each engine ignition related relays, wiring harness if loose or something and last crank sensor. Also check loose fuses too.

[@ramyat1418]

@@dailyhandsdiy thank u so much for ur valuable advise and time, now i can ask my regular mechanic to check the same.

[@dailyhandsdiy]

yup sure. be more specific on ignition relays. as while checking they might wrk great but they can loose its funtion intermittently. And alwys welcome. :D

[@harshitsingh8004]

Sir how to reach you I am facing an issue with Fiesta Engine white smoke please help

[@dailyhandsdiy]

whatsapp me on 9747932260

[@hsb0989]

Sir please suggest on 1issue..my Figo diesel is done 50k kms n when running in 2 or 3 gear in slow rpm without ac at around 900-1000 rpm if I press accelerator slightly then car jerks unless rpm increases n turbo kicks in..this occurs more in cold engine n with heat issue is less..with ac the rpm already gets increased so on pressing accelerator the issue doesn't occur.. overall pick up is excellent.. cleaned MAS sensor but no benefit..air filter already new..diesel filter drained for any water n will change shortly but pick up is good to diesel filter Shud be good..

[@dailyhandsdiy]

Thats normal borther. U see present day cars, engine load calculations are used for fuel injection. At lower rpm and slight acceleration, engine load will be at peak. So it injects fuel in its full Capacity. but the work done on the pistons will be less as oxygen in cylinder will be less. So it struggles to maintain the load. As rpm goes high the load on engine drops significantly. And when turbo kiks in we get a full potential combustion work on piston. So the engine will suffer less load. Thats why vibrates on low rpms and smoth at higher rpm.

[@hsb0989]

@@dailyhandsdiy but please tell why the problem gets less when engine heats up? N this problem is increasing with running.. also pls tell video is about drv valve cleaning or egr valve? Egr have seen is a long 4-5 inch pipe with holes in it..btw today I was able to change stabilizer link rod in my Figo referring ur video which was creating noise over bumps..got at 450 rs from local shop.. i had to use ring spanner and Allen key both to open the nut..thanks

[@dailyhandsdiy]

There are many reasons for it borther, in short, in cold condition, clearance on cylinder parts will be high so air escapes easly which is known as blow by gas. So a complete compression of air will not happen thus lower the combustion efficiency, this put a lot more stress on engine. At as it heats up, components inside expands and clearances will reduce which increase compression and thus proper combustion. There are other reasons like oil and its viscosity, flow rate, sensor functions. Injection timing etc.. Al these are affected by temperature.

[@dailyhandsdiy]

Its egr, ford 1.4 doesn't have a drv valve. Glad to hear from you brother.

[@hsb0989]

@@dailyhandsdiy thank u very much for sincerely replying..have u also created videos for changing outer tie rods? If yes pls share link else pls make one.how to inspect n replace.. thanks once again

[@raaghulkumar7080]

Final satisfying video

[@dailyhandsdiy]

😁👍

[@arunraju9210]

Sir, will cleaning EGR valve solve low pick up when A/C is switched on?

[@dailyhandsdiy]

Its one of the reason for the same issue. A dirty MAF n MAP sensor can also be a reason.

[@arunraju9210]

@@dailyhandsdiy Thank you.

[@dailyhandsdiy]

Alwys welcome

[@vijayam1]

That turbocharger shaft play, is that normal dear? Why is that minute play there?

[@dailyhandsdiy]

Yes thats normal, unlike ball n roller bearing, turbo uses journal bearings. They need a small gap so the oil gets filled there while operating, which keeps the shaft and bearing seperated when spinning.

[@vijayam1]

@@dailyhandsdiy Just as I thought, thank you so much. One more query, my car is a Figo 1.5 TDCI 69k run 2018, new oil, filter everything, which I do myself. Off late, I see white smoke during morning starts for a few minutes then subsides once the engine heats. Once warmed up, no black smoke even if I redline. Oil level is fine, coolant level is fine, no discoloration of coolant. Just morning few puffs of white smoke with the usual diesel-ey eye burning smell, and then normalizes. Glow plugs seems to be fine, any thoughts, please?

[@dailyhandsdiy]

Have you got any check on EGR...? This can happen if the egr is partially stuck open or not closing properly. i have a video on 1.5 to check egr... could use that to find if the egr is sticking or partially stuck open...

[@dailyhandsdiy]

Video link: kzbin.info/www/bejne/aZyUoIyvmpiLjqc

[@vijayam1]

​@@dailyhandsdiy I haven't cleaned the EGR till now. Will do this weekend and see if it helps. That's the only thing I haven't opened up so far. :)

[@jijokoshy9285]

nice video bro...in how many kms we should change the diesel filter... and can u make a video about that too

[@dailyhandsdiy]

sure bro i will. ford recommends at 20k i think. but 30k to 40k kms is adequate. diesel filters wont clog tat easy.

[@jijokoshy9285]

thanks for the information bro... i run a 2006 model ford fiesta ... ur videos helped alot for me.. 🤗

[@dailyhandsdiy]

sure bro ill keep updating :D

[@MrBaskr5]

It's 30000kms once

[@swamiadharpands5910]

Proud of you sir pranam

[@mohammedsajjad5943]

What is the usual mileage of figo TDCI 1.4 engine in city drive ? My car is returning 12 in city and 16 on Highway. Kindly suggest !!

[@dailyhandsdiy]

Depends on the way of driving. On an average, i think 14 ~ 15 in cities and 17 ~ 19 on highway.

[@MrBaskr5]

More than 20 in hway. 18 to 20 in city.

[@dailyhandsdiy]

Haven't ever got 18 on city. but highway yes got more than 20...

[@nostog5085]

Bro.if there any problem to take decarbanisation in ford fiesta 2011.my fiesta have some little pickup issue.some of the bloggers and friends are saying it is helpful to take more power and long life.some mechanics says it very harmful to vehicle.pls tell me what is the real.can I go for it or not😔🙏

[@dailyhandsdiy]

I personally don't recommend bro. Because its believed decarbonising will remove the solid carbon inside the engine by superheating it while combustion using hO molecules or smthing. But its realy not suggested to introduce any kind of accelerators to increase the cylinder temp and blast away carbon inside. It puts too much stress on the pistons and can sometime result in piston and valve deforming or affect metallurgical properties. And also its not evident that it cleans manifolds as its said to work at power stroke inside the cylinder not out side. There wont be any initial problems but eventually some mechanical problems may pop up. And mechanical troubles can tear your pocket apart. None of the engine needs any decarbonising. Jst do the timely oil change, do a manual manifold clean up at each 60k-80k km.

[@nostog5085]

Pls reply me sir.it is very helpful to so many people's🙏

[@dailyhandsdiy]

Please read the replay bro...

[@nostog5085]

Thank u very much bro.

[@dailyhandsdiy]

Always welcome bro. And do clean Maf sensor and egr properly. Might cure the pickup problem. A little lag on pickup could be left unnoticed. No wrys.

[@Face2Fox]

hello brother.hello. i have e60 525d 2004. in the city it drives good and normally but in autostrade afrer 30-40 minutes driving it get warm and start droping the gears. examples ( when it take 5th gear around 100-110 and you press the gass hard it make a noise and stop accelerating). the same with another gear if there is no required speed. and i got light transmission fault. i restart the car and drove manual so like that it work fine but always taking care to have right gear on right speed. please if know this problem tell me the solution thank you

[@dailyhandsdiy]

hey mate, its common in bmw audi vw n skodas to have problems with transmission without proper service. If you have problem with every gear its likely to be the oil itself or the torque converter or the mechatronics. Its common to be the transmission valve body with worn out sleeves or orings causing oil pressure to drop. So a trans mechatronic service with proper replace of o rings n sleeves might cure your problem. Im saying from the common occurrence. A proper diagnosis should be done to find fault. And if its a TC issues, on citys load on the converter is less so might copup with the situations and when at highways or at highr gears load on the converter is high.if there's no proper oil pressure,it slips and cause similar issues. Also a non specified oil can cause this as well.

[@Face2Fox]

@@dailyhandsdiy thanks for answering ❤️… i dont know becouse i bought it just a few weeks ago. i will check about transmission oil level. if there is missing, jan will just fill it up and try? or its not good to mix it without being sure whats provious oil on it

[@dailyhandsdiy]

oh i don't recommend to mix oils if the previous one is not known. Its better to change as whole. These gearboxes are quite sensitive to specificed oil n pressure. If the previous one is to old,the new one can cause varying pressures n cause gear not engaging or shifting unnecessarily.

[@Face2Fox]

@@dailyhandsdiy thanks a lot ❤️

[@dailyhandsdiy]

Any time brother 😊

[@halfengineer6437]

Sir TATA vista TDI model hei uska EGR block ho gya tha to machine ne clean krne ke bjaye total EGR system ko band kr diya, asa krne se koi problem ho sakti hei kya engine ko.?

[@dailyhandsdiy]

nei bro, engind ko kuch nei hoga par engine sound thoda uppar jasakta h.

[@halfengineer6437]

@@dailyhandsdiy thank you bhai for fast reply 🤗

[@dailyhandsdiy]

No problem bro, alwys welcome..

[@sunny-kd9bw]

Hi bro, I tried to clean sensor as you said while cleaning I observed that there is a oil leak from turbo shaft. After cleaning it there was no smoke for 20km and after 20kms smoke started again. One more big problem is my fiesta suddenly turns off while driving and not even starts if we give self start, it only starts when we push the car. If we drive on ac it will start immediately when it gets off suddenly. What will be the problem ?

[@dailyhandsdiy]

I think there's engine heating issue bro. not sure Or and injector excessive leak off problem. or a bad fuel pressure sensor. Have you cleaned maf sensor? Oil inside turbo is normal, its the oil vapour from engine case sucked in by the turbo.

[@sunny-kd9bw]

Ya bro. If the temperature reaches medium car will turn off when we stop somewhere light traffic signals or when we slow vehicle turnings and it will not start until we push or temperature reaches low

[@dailyhandsdiy]

Of course bro, i doubt a failing injector or bad fuel rail pressures sensor. When engine becomes hot, clearnces on injector or pump gets high and fuel pressure will not reach threshold. I suggest to give a check at diesel and pump service station.

[@sunny-kd9bw]

@@dailyhandsdiy Thank you bro, I will let you know if it works. Really appreciate your suggestions keep doing videos and no one else can give reply to everyone like you. Glad to have a person like you in youtube.

[@dailyhandsdiy]

Sure and thank you bro. Made my day :D

[@razi9593]

At what intervals does the EGR valve need cleaning?

[@dailyhandsdiy]

It depends on the driving conditions if living in city areas the interval shld be 40k kms and at highway can go btwn 60k to 70k.

[@varaprasadk6004]

I own ford figo 2012 . Already I asked some other issue and you told me solution. Still I have another issue with my car . When I press acceleration in 1st gear car start jerking and not able to Move forward at up hill in second gear . In idle when I press acceleration for two to three times (revving) rpm start dancing and engine will turn off automatically. When I press break on High speed by pressing clutch car will stall. Is these are caused by egr valve?

[@dailyhandsdiy]

Usually this is more like an air intake matering problem i guess. Ever cleaned the maf sensor or checked the air filter? And rarely non functional egr does exhibit problems similar to the said ones.

[@varaprasadk6004]

@@dailyhandsdiy Don't know bro. I brought second hand car. By the way no warning lights are showing in cluster.

[@dailyhandsdiy]

Bro just disconnect the maf sensor and try driving. n see if any thing changes.

[@varaprasadk6004]

@@dailyhandsdiy your garage location?

[@dailyhandsdiy]

Its in Kerala, Kklm.

[@KarthikK-eo9up]

Nice video bro. My figo has jerking problem when accelerating in 1st & 2nd gear. Can you suggest what could be the prblm...

[@dailyhandsdiy]

Brother i dont feel its an engine related issue. Might be a engine mount issue. or a gear box issue. Does it make any kind of unusual noice while acceleration?

[@KarthikK-eo9up]

Thanks @@dailyhandsdiy ..Not unusual noise, but when fan is running I get engine noise is somewhat high

[@dailyhandsdiy]

Fan noice normal. Does it make... Some thing like tak tak while acceleting. And does it smoke unusually, white or black smoke? . Hows is the behaviour while idling?

[@LittleMultiverse]

@@dailyhandsdiy I have a figo 2011 diesel meri car me aati h tak tak ki sound

[@dailyhandsdiy]

@@LittleMultiverse Yes bro sounding tak tak in slight acceleration is the main symptom of injector going bad.

[@hemanthkumarw8710]

Hey great video! Could you help us with a PCV valve video on Figo? Thank you 😊

[@dailyhandsdiy]

Bro there's no pcv valve in ford tdci engines. pressure at crank case is kept negative using turbo's suction. you can see a small pipe jst b4 the turbo inlet going from main inlet hose to cv filter on the top of engine.

[@hemanthkumarw8710]

@@dailyhandsdiy thank you for your response bro. I see oil accumulation on the small pipe (not near the turbo) but on the other side of the small pipe and the oil is being sucked all the way near to turbo. As I checked there is no lag in turbo as well... Just confused what could be the reason. Please let me know what could be causing this? Thanks again!

[@dailyhandsdiy]

Dont have to worry bro. Jst put a hose clamp or cable tie. during hot performance that small pipe expands due to heat and oil vapour from pcv filter leaks out through that pipe inserting area. thats y oil stains seen there. using clamp will seal the loose hose properly.

[@hemanthkumarw8710]

@@dailyhandsdiy Thank you so much :)

[@dailyhandsdiy]

Always welcome bro ;D

[@xdude361]

bro iam from trivandrum...where is your shop?? is it safe cleaning egr with hit??as you shown cleaning maf sensor??plz reply

[@xdude361]

Is it safe bro?

[@dailyhandsdiy]

Bro i dont run a shop. Jst know the stuff. its totally safe to use hit. jst need some time to dry up. tats ol. i hv been using hit for my both vista n figo for years. till now runs great.

[@xdude361]

from your previous video about maf ...,today i cleaned my fiesta maf sensor successfully...but i could nt open egr, i think i need a different tool ...

[@dailyhandsdiy]

bro egr is fastened by 3 small bolts. use a 5mm normal hex socket. it matches the bolt.

[@xdude361]

@@dailyhandsdiy could you plz share a pic of that??

[@jibinjacob7156]

Bro naatil evideya .. do u have a workshop or something...bcoz I need to clean my egr valve of my 2011 figo Diesel.. can't do it myself..

[@dailyhandsdiy]

Koothattukulam. Your place?

[@jibinjacob7156]

Kottarakara

[@dailyhandsdiy]

Dhuram kuduthal anallo bro.

[@jibinjacob7156]

Bro njn ee month end vellom angottu veraam vilichittu .Then we will meet up one day .. plz share ur number

[@jibinjacob7156]

Bro my figo is actually a remapped one ..so egr cleaning is a must rite?

[@bharatsuthar8334]

I have ford figo 1.4 diesel .in morning start the car too much vibrate and after 2 km 3 km driving the run smooth. The dtc code show. P0360 & P0370. i change maf sensor also.i remove the egr plug because of faulty egr.

[@dailyhandsdiy]

According to the dtc its an engine wiring fault or corrosion. Check the wiring to cam and crank shaft position sensors, check sensors for dust or oil spreading, check timing and crank shaft timing ring for damage.

[@bharatsuthar8334]

Misfiring can occur by egr or not.in morning

[@dailyhandsdiy]

Egr won't cause any misfire. It will give huge white smoke in the morning and black smoke whn the engine is warm with low fuel mileage and power.

[@bharatsuthar8334]

In ford figo 1.4 diesel .Does the glow plug work in the morning or not?. Because the dtc code show in my car p0380.some problem with this cause in car.

[@dailyhandsdiy]

Yup glow plugs works at every starting point of the engine. Either the connectors can get oxidised or the plugs may have gone bad.

[@jineshjosepthomas4335]

Sir, Need your help My Figo is 2012 model covered 120000km, recently the car started to slow down while ac on, without ac car run smoothly. Pls suggest a solution sir.

[@dailyhandsdiy]

Bro Hav you noticed any winning king sound from ac compressor.?

[@dailyhandsdiy]

First clean the maf sensor and check if it resolves second check if there's any vaccum leak on the turbo inlet pipe. 3rd could be an egr malfunction. Engine load and egr funtion, every thing is depended on maf sensor. So basic thing is to clean and check maf, vaccum leaks on pipes, and check air filter.

[@jineshjosepthomas4335]

@@dailyhandsdiy Sir, Once I done with maf sensor check I will back to u with the outcome. Thanks so much for you time and precious reply sir. Have a good day 👍

[@jineshjosepthomas4335]

@@dailyhandsdiy No abnormal sounds from ac compressor . Those quite as before sir.

[@dailyhandsdiy]

Ok brother, so the compressor feels good, now check the above said things and see the outcome. Thnks for the support and alwys welcome bro.

[@joeantony1632]

For egr sensor it's 5mm hex drive or 5mm torx drive..pls replay

[@dailyhandsdiy]

Its 5mm hex type.

[@joeantony1632]

@@dailyhandsdiy for hex bolt there is no curve and these have some curves...will it work with hex drive

[@dailyhandsdiy]

yes bro. its a male torx bolt. but can also be loosen by hex drives. i used hex drive to loosen those bolts.

[@joeantony1632]

@@dailyhandsdiy thanks

[@dailyhandsdiy]

welcome bro

[@theveera9415]

What type of spray is used for cleaning

[@dailyhandsdiy]

I used HIT bro, easly available in market with alcohol additives.

[@varaprasadk6004]

@@dailyhandsdiy give me link of that product

[@dailyhandsdiy]

Its available in local market stores...kala hit 😌

[@varaprasadk6004]

@@dailyhandsdiy can i use that Hit for both maf sensor and egr cleaning?

[@dailyhandsdiy]

For maf ok, For egr first use diesel to soak the soot,then use Hit to wash out sludge.

[@Ben-bu2jg]

Hey, thanks for the video, very useful. However I had a bad EGR a few weeks ago (had EML on permanently) . Bought a second hand EGR and fitted it; light went out. However a few weeks later the car judders now and then and idles rough. Do you think it’s the EGR or a MAF sensor? I’ve had no dash lights and I understand it’s hard for you to diagnose but just after some advice please? I’m thinking I’ll follow this video and clean the valve but I’d rather not haha. Thanks

[@dailyhandsdiy]

Hi brother It could be dirty MAF. if maf does not perform well, it affect egr as well. Try cleaning MAF first and see if it resolves. I have a video of cleaning maf easily.

[@dailyhandsdiy]

kzbin.info/www/bejne/gpzdm5-tp9hmrs0

[@Ben-bu2jg]

@@dailyhandsdiy thank you very much. Is it worth waiting for a code to be thrown up because it’s weird. One day the car will drive like a dream the next like crap so it’s the old dilemma of if it’s not broke don’t fix it

[@dailyhandsdiy]

Bro ford engine is so sensitive to sensors. Jst clean the maf sensor, wont take much time. Can be done by yrslf.

[@Ben-bu2jg]

@@dailyhandsdiy thanks very much mate, appreciate your time and help. Take it easy

[@bkrishnacse]

Hi bro, i haved Scanned with obd2 Scanner. got 3 fault codes. my self only scanned p042f(video which your showing) p0341 p1602 These are Major issues ?

[@dailyhandsdiy]

Kind of... first one is from egr, so need an egr clean up. Second one is for cam/crank shaft sensor miscalculation which can be of bad timing or failing cam or crank sensor( need attention), third can be bcs of battery discharging fast or battery going bad.

[@dailyhandsdiy]

secnd one need an attention becs it can cause sudden engine break down any time.

[@bkrishnacse]

okay bro... will goto Showroom ASAP will Fix issues..

[@bkrishnacse]

@@dailyhandsdiy third one is we are discussed 2 days back regarding battery discharge frequently

[@dailyhandsdiy]

Yes yes i remember. :D

[@madhubala3926]

Diesal car leakage in comman yes or no pls

[@dailyhandsdiy]

If you mean oil leaks then yes, unlike petrol engine, diesel engine vibrates more. This will make the oil seal nd sealants to wear fast. But its rare in modern engine technology. its a 50 50 chance.

[@ShivamSharmaRepairs]

Nice video 👌

[@dailyhandsdiy]

Thanks bro. 😀😀

[@ShivamSharmaRepairs]

Bro tata manza ka jo race issue tha na vo bhot pareshan hogya usse yek kera 7000rs lunga or yek 3500rs wiring or yek 11000 ecm change hoga sab ne check krke bataya Plot twists : kya huaa car ka gesr cable lock nikal gya use toh usse msi bend wire se theek Kara tha toh aasi check kiya wiring dekhi sab ok fir throttle body ka wire nikala or mobile ke camera se socket check kiya toh vo bent tha 😅 fir camera on krke pin se sidha kardiya mechanic bhi yrr bhot experiment krte hai or apni jeb kat thi hai

[@dailyhandsdiy]

wow all those money for a miss aligned socket. Tru bro, mene bhi ese mechanics ko exprnce kiya h. bina chk kiye seeda replace. So car's now good?

[@ShivamSharmaRepairs]

@@dailyhandsdiy car is in perfect now 😊😊 thank you for all help.. kabhi kabhi khud bhi check krna chahiye... Agar mai unke pass car chood deta toh vo ni bolte pin mudi hai sidha boldete ki wiring thik kari ye kara vo Kara dijiye sir 5000rs 😂😌

[@dailyhandsdiy]

So tru 😀. any way its good to hear from you bro.

[@sunsetfunset]

I can't get the uoper spindle guide out. Ive tried everything

[@dailyhandsdiy]

It must be stuck by carbon build up... two gentle taps n it will come out.

[@bigdaddy2dwitiya]

Is it good to remove egr permanently ? Ford Figo 2010 TDCi ?

[@dailyhandsdiy]

Car will run much better

[@bigdaddy2dwitiya]

​@@dailyhandsdiyWhat should I do ? Should I just unplug it or I've to delete it and apply blanking plates to it ? Just unplugging it can cause any harm to the engine? And talking about blanking plates they aren't available in Indian, so can just unplugging it would work ?

[@dailyhandsdiy]

Yes just unplugging would do, there will be check engine light..its not harmful for the engine but to Earth...yes...Could also do a software delete

[@bigdaddy2dwitiya]

@@dailyhandsdiy thank you for the information... I've already got a check engine light for the EGR sensor and was about to change it. The mechanic did cleaning but still my problem wasn't solved so he suggested a replacement. I'm sorry for mother earth🌍...

[@dailyhandsdiy]

Any time brother

[@greengame5115]

Bro fiesta turbo hoseil oil varunnu but turbo play normal anu, i suspect the oil is from pcv , ith enginene affect cheyyuo

[@dailyhandsdiy]

Illa bro... ath angne anu oil vapour varum, karyamakkanda.

[@greengame5115]

@@dailyhandsdiy Thanks bro your videos are very informative

[@dailyhandsdiy]

Made my day bro...

[@makvlogs8091]

Bro EGR ko block Karke v car assi chalto he na?

[@dailyhandsdiy]

emissions me fark ayega bro...

[@jasvirsomal9313]

Bro after how much interval it should be cleaned?

[@dailyhandsdiy]

Its anywhere btwn 40 to 60k kms bro.

[@jasvirsomal9313]

@@dailyhandsdiy thanks for quick reply bro,i bought 68k driven figo serviced from ford service center.Did they have ever cleaned egr till now?

[@dailyhandsdiy]

No bro. they'l never clean it before 1 lakh km i guess or when a problem pops up. Better do it right now. and also do a proper oil change, do all the engine sensors. Your car il be fine.

[@jasvirsomal9313]

@@dailyhandsdiy thanks bro,my figo's sound also increases(almost double) when i turn on A.C.is it normal bro?

[@dailyhandsdiy]

Tats perfectly normal bro. engine sound changes with varying load. need not wry at al.

[@fayizct8039]

Is it recommended to clean egr in a periodic manner or just when fault occurs?

[@dailyhandsdiy]

its always preventive. The fault will be no acceleration and if you're running up a hill......you're stuck.

[@fayizct8039]

@@dailyhandsdiy may i know the intervel

[@dailyhandsdiy]

40k to 50k is best suited interval for ford

[@AshokKumar-hg8nx]

What happen if spindel guide is missing in egr

[@dailyhandsdiy]

EGR valve stays open all the time....white smoke, no acceleration, engine shaking etc can be seen

[@AshokKumar-hg8nx]

@@dailyhandsdiy sir after egr clean i have face problem of pickup while driving i have accelerate full padel but nothing happened and after some time rpm gone above 3 to 4k

[@AshokKumar-hg8nx]

@@dailyhandsdiy sound of engine is more silent after cleaning, no white smoke come

[@daddycool8875]

Bro, i clean the EGR with WD 40 and fit it back but my car cannot start. I don't know what to do now. Please help

[@dailyhandsdiy]

Check all the connections, sensor wirings etc if its loose or not connected.

[@daddycool8875]

All are connected... I reassamble three time but cannot start.. what can be the problem?

[@dailyhandsdiy]

Have you prime the fuel line?

[@daddycool8875]

@@dailyhandsdiy Yes I prime it. I even charge the battery two times already. When I scan with OBD eror code P0404 was there

[@dailyhandsdiy]

There's something wrong with the fitting. Try disconnecting the valve electrical connector and start the car.

[@sureshmallavarapu8204]

Soo kind of you ..... 👍

[@dailyhandsdiy]

Thanks bro :)

[@MrBaskr5]

What are the symptoms that it's time to clean EGR?

[@dailyhandsdiy]

Too much black smoke, too much white smoke on cold start whith strong pungent smell of diesel, Intermittent power loss, lack of pedal response, too much flat sound on heavy acceleration, turbo not kickin in, and last dtc....

[@MrBaskr5]

@@dailyhandsdiy running 79k kms.shd I tell them to clean EGR ? Not too much smoke but lag in power sometime.

[@MrBaskr5]

@@dailyhandsdiy bought 2nd hand at 55kms... Been pouring stp injector cleaner 5000kms once...

[@dailyhandsdiy]

Ford egr is too much vulnerable to sticking so a clean up at 40k km would be nice.

[@Sajad_19]

bro ford figo shows egr current fault after scanning and check engine light also come on...what is show on the video everything i do but still problem presists

[@dailyhandsdiy]

There should be problem with the egr motor or the part must be cleaned properly.

[@Sajad_19]

Still error after cleaning... is there any fuse of egr in ford figo

[@dailyhandsdiy]

nop there's no particular fuse for egr in ford.

[@Pixelvision63]

Bro do you have workshop..

[@rahulthakur1648]

Plz make more video on old ford figo diesel 🙏🙏🙏🙏👍👍👍👍

[@dailyhandsdiy]

Sure brother 😊👍

[@samiahamdi3771]

Good job

[@dailyhandsdiy]

Thanks mate

[@samiahamdi3771]

@@dailyhandsdiy thank u very much I done same job its perfect now 👌 😍

[@dailyhandsdiy]

Glad to hear from you brother.

[@xdude361]

Bro i need a help... my fiesta gas mileage reduced drastically.. i tried maf cleaning.. still no change... now iam getting only 9 km per litre of diesel... please suggest me a solution.. waiting for your reply..

[@dailyhandsdiy]

was the sensor properly dried b4 reassembling?

[@xdude361]

@@dailyhandsdiy yes.. i dried it with hair dryer

[@xdude361]

സെൻസർ ക്ലീനിങ് നു മുന്നേ തന്നെ ഈൗ പ്രശ്നം ഉണ്ടാരുന്നു.. i thought it will be cleared after cleaning the maf.. but in vain

[@dailyhandsdiy]

egr cleaning cheytharno?

[@xdude361]

@@dailyhandsdiy illaaa

[@sanload123]

I cleaned the egr valve at ford service centre but after cleaning the car is jerking and stopping. I am getting p1335( EGR Position Sensor Minimum Stop Performance). They are asking to replace with new egr valve costing Rs 21000. Pls help car is at unusable left at ford service centre now.any solution ?before Cleaning egr error code was p0404(.EGR valve position control performance or range fault)

[@muhammedwazeem9557]

bro iam also facing same problem

[@jijokoshy9285]

not necessary to remove the whole egr with pipe??

[@dailyhandsdiy]

No bro. ford doesn't has a gas cooler. so not need to take the whole assembly. Jst making the actuator move freely is more than enough.

[@jijokoshy9285]

some cars i have seen the whole pipe filled with carbon and oil. in that case i guess it's better to dismantle the whole assembly

[@dailyhandsdiy]

In cars with gas cooler, need a dismantle. but without cooler doesn't matter. the nxt day u clean the pipe all tat carbon and oil be back there. By the way bro, this is to check sticking egr valve. even if theres no clogs, soot gets into spindle gaps and makes spindle difficult to move. in tat case this is usefull. a simple way to check egr.

[@ابنبطوطه-ك6ك]

I changed the EGR with new one ... but the engine lights still on ?! And service lights also on ?! I did I cleared the codes with the scanner but they keep coming back?!

[@dailyhandsdiy]

What codes are shown?

[@ابنبطوطه-ك6ك]

@@dailyhandsdiy p042f .... sometimes engine light and sometimes the power train lights flashing and the car loses power ?!

[@dailyhandsdiy]

Sry fr the delay, have you checked the new egr if its working before installation?

[@dailyhandsdiy]

Remove the motor from valve and with connected check if its working when car turned on.

[@ابنبطوطه-ك6ك]

@@dailyhandsdiy great ... many thanks for replying .👍

[@kenaokonthoujam8409]

plizzz reply SIR , my ford figo tdci 2012 everyday it runs smoothly with a cold start but after driving 1-2km it starts knocking with kat222 wala diesel sound. I had tested the injectors and they are working fine. Please help me

[@dailyhandsdiy]

Usually the knock in tdci engines comes from the injectors going bad. other reasons are timing errors, wrong fuel pressure...etc..pls make sure if its a diesel knock or cause of some other worn out parts.

[@kenaokonthoujam8409]

ok sir, my car's performance is unconsistent , and it performed better after revving the engine but before revving performance is weak with harsh sounding which seems like struggling with fuel combustion or something

[@partha5402]

ford fiesta diesel white smoke on high rpm..why?

[@dailyhandsdiy]

Ford engines pushes smoke at high rpms...thats normal...just look if it gives out that amount of smoke below 2300 RPM

[@nishaangobind8480]

Hi bro, been watching ur videos...extremely useful advice. I have a Figo 1.4tdci and have been getting intermittent misfire or jerks and black smoke. Not sure if this could be the fuel pressure sensor or the rail. Thought it was fuel filter and replaced it but still doing the same. Recently discovered that the radiator fan is not coming on so not sure if the temp sensor can cause the car to have the intermittent misfire or jerk and black smoke. Diagnostics@ local ford dealership read as follows, Description: P0192 FRP sensor low input This DTC may be caused by: Pressure regulating valves or controls FRP sensor/wiring Fuel injector faults Wiring harness Chafe in the area of transmission. 2nd diagnostics read as follows (same day...2 diff diagnostics) Description P0194 Fuel rail pressure sensor intermittent This DTC may be caused by: Damaged or contaminated connector Faulty or damaged PCM Not sure what to go with as they've done diagnostics on the same day with differences in diagnostics

[@dailyhandsdiy]

Hi there, do check the wiring first. Both on the regulator and sensor. Clean them both. From the diagnostics looks like the fault is from the FRP sensor side bcs of p0194. A fault in regulator does show p0192 but not p0194. A fault in FRP can cause the regulator to mis operate and throw p0192. And the radiator fan only turns on when the coolant temp hits 105 degrees. Do check if the fan works when AC is turned on. Do these first and check if the issue reoccurs.

[@nishaangobind8480]

Txs will look at this and revert.

[@dailyhandsdiy]

Sure

[@nishaangobind8480]

@@dailyhandsdiy removed and cleaned egr valve and the car is driving perfect

[@theveera9415]

Bro make a video on throttle body cleaning of Figo

[@dailyhandsdiy]

of petrol engine?

[@theveera9415]

@@dailyhandsdiydiesel

[@theveera9415]

Bro and another my Figo getting overheated bro

[@dailyhandsdiy]

bro diesel doesnot have a throttle body. Did u mean inlet manifold? I will surely do...

[@theveera9415]

@@dailyhandsdiy s bro

[@bikashgurung7777]

Bhaiya mana apka vedio dak k khola but egr ka upor k bolt khol dala so spring nikal gaya ab star nahi horaha

[@dailyhandsdiy]

Now you should reset and fix the spring... bro u shouldnt have opened the motor body. its a complicated mechanical device.

[@lwanelemadonsela186]

I have a Ford Figo 1.4 petrol 2010 model. Recently it has been releasing smoke from the engine like its from the plugs. Now it is refusing to starts i have to keep on trying until it starts well. I have changed NGK plugs twice now. What maybe the problem?

[@dailyhandsdiy]

How much kilometers run?

[@lwanelemadonsela186]

@@dailyhandsdiy 170 000

[@dailyhandsdiy]

looks like piston rings have worn. Changing spark plugs won't cure it. Have to do a compression test on each cylinders. Its buring oil tats why its emitting smoke.

[@sureshmallavarapu8204]

Bro I've done the same process but after fitting fuel not coming to filter and car not starting

[@sureshmallavarapu8204]

Please help

[@dailyhandsdiy]

You have to prime the fuel bro, using the priming bellow

[@sureshmallavarapu8204]

Done it and also checked the line coming from tank to filter. No fuel is coming..

[@dailyhandsdiy]

oh the below is busted, bro do one thing, find the fuel return line and carefully suck till the fuel comes. Immediately connect the line back. Sould do that carefully.

[@sureshmallavarapu8204]

@@dailyhandsdiy Bro is there any other way i can connect you to explain little clearer

[@shakkeersha007]

Thanks❤

[@dailyhandsdiy]

Gald to hear from you mate.

[@jsupport4792]

Hi sir pls provide your no. I want repair my ford fiesta 2012 diesel white smoke issue

[@dailyhandsdiy]

9747932260 pls whatsapp me i l get back to u asap.

[@user34202]

Showrumil EGR valve stuck പറഞ്ഞു.22k 💵 മാറ്റണം. പുറത്ത് cleen ചയ്താ ശരിയാകുമൊ. Injector problm വന്ന് recondition ചെയ്യതതാ.😰

[@dailyhandsdiy]

Porath cheyicha mathi, stuck ayal proper ay clean cheytha seriyavum.

[@dailyhandsdiy]

morningil matram ano atho eppozhum undo?

[@dailyhandsdiy]

@@user34202 turbo inlet hose jst onn azhich athinte turbinu play endorum unden onn noku...cheriya oru play ano atho elakunnundonn ariyam. Evide anu ee sthlam?

[@dailyhandsdiy]

turbo core vangan kittumengil 5k okke avu.. full housing okke included anel oru 12 k okke avum

[@dailyhandsdiy]

@@user34202 turbo thanne ano complaint enn nokkanam.. white smoke injectr karanam avanam, egr karanam avam, boost leak karanam avam. so sure avanam which one.

[@bikashgurung7777]

Ab kiya karaga

[@dailyhandsdiy]

ab vo spring vapas set karna hoga..

[@adilm2450]

Tell me

[@dailyhandsdiy]

Tell what bro?

[@adilm2450]

@@dailyhandsdiy speaking with video

[@dailyhandsdiy]

Yes bro did that intentionally, bcs if did talk in video, it would be my regional language which is malayalam and the video gets regionalised. And you wont understand a thing m saying. And if i dont talk and show all the procedures continuously, you can watch and diy.

[@kingshukchatterjee7555]

hey bro, I have a ford fiesta titanium globel version 2012 diesel model, I bought it 2nd hand ,,108000 km running. there is too much black smoke from the silencer and the pick up and mileage is also slow down, the local mechanic tell me that my car engine needs service and it will cost nearly 60000 rupees ,tell me what should i do?

[@dailyhandsdiy]

Bro first and mostly check the egr for clogs, turbo, clean maf and map sensor. Does your car takes longer cranking on morning?

[@kingshukchatterjee7555]

@@dailyhandsdiy no bro..1st selve start

[@dailyhandsdiy]

i mean does it take more than 4 secs to start the engine?

[@dailyhandsdiy]

If starts fine in the morning and no issues with startup, you might not need an engine ovrhul. Jst check athe above mentioned things and see if it cures. Clean maf n map sensor first. And see.

[@kingshukchatterjee7555]

@@dailyhandsdiy okey bro... thank you soo much..