BMW E46 M3 LSD mechanical conversion upgrade | Viscous to clutch type conversion

#E46M3 #LSDdiff #upgrade #RacingDiffs #GKN
Phase II LSD upgrade pack for E46 M3 LSD installation tutorial. This kit by RacingDiffs converts your factory viscous-clutch type to purely mechanical clutch-type LSD unit.
If you track your car, than this is a must.
The kit is available for purchase at following link:
racingdiffs.com/products/bmw-...
Download our gear calculator App for IOS and Android and claim exclusive 10% OFF!
Connect with us on social media:
/ racingdiffs
/ racingdiffs
Don't forget to subscribe.
Chapters:
00:00 Intro
02:59 Removing the crown gear and opening the unit
05:57 RacingDiffs kit unboxing
07:38 RacingDiffs kit installation
12:01 Conclusions

[@scipperdsbc9521]

❤️ danke

[@ZweiGeMotorsport]

Thrust plates on bmw differentials are for progressive clutch engagement .

[@johnoliverio8729]

Nice video. My factory LSD is dragging after only 50,000 miles. Are the mechanical LSD's easier on friction and wearing out? 2004 M3 Manual. Thank you

[@RacingDiffs]

You're not the only one. We fixed many diffs under 50k miles in our shop. With this upgrade, you will get rid of noises for good and gain some performance too. And if you wish the top-level performance, then I suggest a fully mechanical LSD unit. racingdiffs.com/collections/all-solution-lsd-unit/products/bmw-high-performance-lsd-unit?variant=33671152959623

[@danharborow6963]

When fitting this kitt what breakaway torque should I expect to see with this conversion please?

[@RacingDiffs]

100-110Nm after break-in

[@jeffn8000]

Just to confirm - if my factory viscous unit (V1) is no longer operating correctly (minimal lockup, has clunk), just this kit installed as shown in this video should repair? There is no need (as shown in the full rebuild video) to replace (cut & press) the shaft bearings? Is this correct? Thank you!

[@RacingDiffs]

That is right. As addition, if you have whining noise on straight line, than you should change bearings.

[@jeffn8000]

@@RacingDiffs Thank you! No whine...just a really sucky LSD. :)

[@RacingDiffs]

Than you can get away with cheaper options of rebuild 🙂

[@mrgizmo7975]

Is v2 unit better? Can it handle more power? Does it wear out less frequently due to it's design?

[@RacingDiffs]

Not really. Basically they are the same.

[@mrgizmo7975]

@@RacingDiffs v1 is so much quicker to do, no c clips, no special tool to open/close the lid, no press to realign the slider gear rod, etc. Also seems like on v1, when you put it together, there is no finer adjustment of preload, where on v2 you can tighten the cap more, to a certain point. So v1 relies on internals thickness to provide the right preload.

[@RacingDiffs]

@@mrgizmo7975 exactly.

[@lyem654]

@@mrgizmo7975 What if I end up with too much clutch preload on V1, and what can I do to get it right? Compared to V2 I can adjust the lock ring -- dial it in for the desired clutch preload.

[@RacingDiffs]

In V1 unit, you can't adjust preload that easily as in V2. You have to play with thickness. Our outer plates are slightly thicker than oem, so if you have too much preload for your taste, you can combine oem outer plates and ours to find the best combo for your application.

[@jackclement3941]

Will this lock the wheels faster and act in a similar manner to a 12 pack clutch LSD kit

[@RacingDiffs]

Pretty much, yes. It keeps clutch pack engaged all the time with minimal 30%, which improves LSD response by far.

[@jackclement3941]

Awesome; are you having a Black Friday sale and will these be discounted?

[@RacingDiffs]

We are having a Black Friday sale at the moment. They are discounted 30%. If you decide to get Bearings and seals, you will get an additional 10% off. racingdiffs.com/collections/lsd-clutch-plate/products/bmw-m3-m5-m6-z4m-lsd-differential-rebuild-kit?variant=42497704788204

[@antanasrapkevicius3897]

i got a kit from you guys. my original LSD had 7/8 plate clutch, the one i was sent is only 5/6? Is this some mistake? what's the reason dropping down 2 clutch plates if so? O have i got the wrong kit sent?

[@RacingDiffs]

All is fine. Since our plates have a higher friction coefficient, we dropped 2 clutches to make room for preload shim, which is far more significant upgrade.

[@antanasrapkevicius3897]

@@RacingDiffs Thanks for the update. I was getting a bit worried I didn't get full/correct kit as looking at the other video of LSD rebuild V1 E46 M3 on your channel I had also counted there were 7 clutches in your kit to replace. May I also ask what's the average life expectance of the clutch pack? 30000km? 50000?

[@RacingDiffs]

@antanasrapkevicius3897 depends on the usage. If you drive it on the street, it will last much longer, of course. Make sure you use quality oil such as Motul gear competition and change it every 2 years.

[@DerKaktusAvant]

I didn’t fit the large shim as I couldn’t find this video. It isn’t linked on your website etc. Is it going to cause a problem? I don’t want to have to do this job again…

[@RacingDiffs]

All parts should be fitted. If you have any dilemmas regarding the installation procedure, our support team is available mon-frd to answer all your questions.

[@DerKaktusAvant]

@@RacingDiffs looks like I’m taking the diff back out again … Could you link this video on your website, so no one else makes the same mistake. I only found another video where someone mentions that it shouldn’t be fitted.

[@manuelcastaneda7102]

I broke one of the clutches with the teeth outside , will you guys sell me just the one clutch

[@RacingDiffs]

Write email with pictures to [e-mail]. guys from the support will take over👍🏻