Radical Firearms and the Cheap Gun Mafia

[@RimfireSS]

If you want that rifle to run steel case open up the gas port alittle. Radical uses a .625 gas port which runs higher pressure brass just fine but the lower pressure steel case is no bueno. The nice thing about the .625 gas port is it’s softer shooting with brass case. Hell I’ve had a few barrels over the years that the gas port wasn’t even drilled. Lol. When you put the suppressor on I knew it would run the steel case. Long story short if you plan on running steel case either throw a suppressor on it or open up the gas port. Radicals are cheap guns, quality control is not so good, loose Handguards and under gassing is the price you pay….. you gotta tinker with it abit. Lol you get what you pay for. I actually get a kick out of making cheap rifles run. And there’s no way Radicals are just as good as the expensive rifles. But with some tinkering you can get them to run just fine. Don’t let the people in the comments get to you. Takes thick skin to be on KZbin my friend. Ignore the haters and the cheap gun mafia!

[@wyominggunproject]

Yeah I figured it was a little under gassed for the steel stuff. I also don’t mind tinkering around with cheaper guns. I knew what I was getting into when I bought it. Just wanted to see for myself what a $400 dollar AR was like. Thanks for the comment and screw the Cheap Gun Mafia. 🤠

[@catherineslowincomepreppin2128]

Your so right as I said in my post to Wyoming gun project ,mine worked out well, after I spent hours reworking my 2 ar-15's. I consider myself a hunter, survivalist/prepper 😉

[@jerrodbates8480]

You can also see that the cases have no velocity getting ejected

[@williamrogers.]

Sounds like a great gun for a suppressor.

[@sleigh4019]

100% .. He seems to be taken this personally lol ..its not as good ..its a budget gun

[@dadadadada4974]

Some cars require premium gas… in a similar sense, premium rifles can handle crap ammo… but budget ones require premium full strength ammo.

[@thecornastore]

My thoughts exactly..has to be the gas system or the buffer spring...either way it typically seems like the gun jus needs a hotter load😂😂😂😂that sounds so nasty

[@Gunsandfun1961]

My RA 15 eats everything...sorry I must have got a good one 😂

[@ExploringDarknessGhostM6edia]

You Said It My Brother...I Just Ordered My Radical AR.. What he is no saying is you need to run about 100 150 rounds of 5.6 ammo through it and then shoot the cheaper stuff..My Brother has over 2,000 rounds through his RADICAL AR and it runs what ever he puts in it... Radical AR15 is well worth the money and then some.. Watch !! Mark My Words ! You Will See Radical AR15s Over 1,000 In The next Year Or So..I Think he4's BUTT HURT THAT HE SPENT ALL THAT MONEY ON HIS OTHER ARs. AND THIS GUY CALLING A RADICAL AR15 A TOY..PLEASE HE'S A MEATBALL.. Radical Keep Up The Good Work ! GregM From EXPLORING DARKNESS Ghost Media..

[@darkvader0248]

@@ExploringDarknessGhostM6ediathey are a toy, they are not duty quality when I’d you “get a good one” or not is luck of the draw. Theirs a hierarchy for a reason

[@blackicekck9family379]

Well said 9:42

[@partiallytrainedsemipro]

had to lighten the buffer on mine and now does fine

[@Maurice3774]

I will never use steel in any weapon I own

[@wyominggunproject]

Good for you I do. BTW are you the president of the Cheap Gun Mafia or just the CEO?

[@destrycook24]

@@wyominggunprojectthat has nothing to do with cheap guns man. Steel case runs dirty it can have issues with cases splitting and can’t be reloaded. I won’t ever use steel case in my guns and I don’t buy cheap guns. There’s also a lot of expensive guns that won’t run steel. The guys just saying he doesn’t like steel ammo does no good to make fun of the guy.

[@TheZombie567]

Strips the rifling over time

[@jeffk1485]

If it won't shoot steel, it doesn't deserve brass.

[@saleenfanning23]

​@Glatisant_galla wait, did I get fired???😂😂

[@DodgersLH714]

I love my Radical, no malfunctions. My first AR

[@wyominggunproject]

I am glad to hear it. 🤠

[@zed332l]

Cold, day Bad guys at the door get me my proven "stuff". That I KNOW goes bang EVERYTIME.

[@GreatWhiteShark75]

I got a Radical AR-15 as a gift along with 7 30 round mags. I've told people with more powerful rifles this: "If it can defend my house and family, that's my gun." People just have different choices, and I honor that.

[@Rifleman917]

I have a 10.5in RF-15 -- or whatever they call it -- and I've had a mixed experience with it. When I first took it out, I noticed that the firing pin struck the first two or three rounds without fully igniting the primer, but I did a quick field strip, lubed it up just enough and it worked fine after that. Now about 400-500 rounds through it, some of it dry and other days are right after a clean, with no issues. I tend to shoot up in the mountains so dust/debris are a constant. I enjoy shooting mine, but I 100% agree you get what you pay for on these things. The polymer feels cheap, and I'm always slightly nervous about the internals. This is certainly not my go-to combat rifle...

[@wyominggunproject]

That’s all I was trying to say. 🤠

[@qthestorm_patriot]

I never had an issue with my 10.5 it runs superb.

[@392JT]

you run 762 or 556 ?

[@392JT]

@@qthestorm_patriot you run 556 or 762 ?????

[@marksini3598]

I haven't had any issues with steel cases

[@MicahAnointed]

I own a radical and haven’t had any issues with it. It’s a budget rifle for fun and I don’t claim it to be anything greater than what it is. With that being said your video was not offensive at all and your sense of humor and straight forward attitude was appreciated. Keep up the good work bro! 👍🔥

[@wyominggunproject]

Thanks man. I appreciate you getting the point of the video and picking up on the humor. I want ALL firearms manufacturers to do great and give their customers decent products. Thanks for watching dude 🤠

[@tberkoff]

You know WGP is fired up when he puts out a 31 minute video! LOL If people are commenting on your videos on other channels, it means you are doing well!

[@wyominggunproject]

Thanks 🤣🤣🤣

[@sleigh4019]

Spend 599-650$ on BCM upper and you'll get the top of the line gun at a fair price .. There is a issue with 1200-3500 guns being overpriced

[@zed332l]

I have an IWI Zion I bought in testing as a new defense weapon for the family so far, I am impressed.

[@saleen12]

I wish bcm uppers were 600 😂😂😂

[@MrBossuporbowout]

Ive seen and have heard of several so called high end rifle that wont shoot steel cased ammo and are sensitive to reloads. Thats why I went to AKs where the tierism is minimal lol

[@GanjaBabyy]

It's either 2 things. Its the Ammo which is underpowered, this happens with .223 in my wbp jack 5.56, #2 its possible the gasblock isnt installed perfectly..

[@zed332l]

Have you tried steel in 556?

[@markzuckerberg3128]

My opinion is the mid priced AR rifles are probably the best buys. The gucci rifles are definitely overpriced brand name mark up. The budgets rifle do cut corners. The cool things about AR's is you can change out components and fix problems pretty easy. Buy a cheap rifle, upgrade the bolt, upgrade the barrel. Then you have a good rifle and probably saved a few hundred dollars still.

[@wyominggunproject]

Very true 🤠

[@definitelynotthea.t.f.8813]

Couple things you are not taking account of. By the time you swap in mid-tier parts like Aero, BCM, etc the parts and price of gun are at least 2/3 the way to a Gucci gun.

[@definitelynotthea.t.f.8813]

Now if you’re gonna be putting pretty nice parts in and the cost starts adding up…. The place to save money in you budget is not on your “end of the world Gun”.

[@markzuckerberg3128]

@@definitelynotthea.t.f.8813 Not really. BCM Bolt is about $100. A good barrel is about $350. Buy a cheap rifle for $450+450, you've spend $900. Way cheaper than a $2500 gucci rifle.

[@donwyoming1936]

I don't think I'll ever bet my life on any of my cheap ARs. I'll grab a Colt. 🤠

[@ForrestMilton-y6t]

They will only take Tula ammo after they’ve been broken in or you’ve switched to a 4oz buffer.

[@bradd8383]

Go heavy or go home

[@WesB-Tactical]

@@bradd8383💯🫡🔥

[@RL69420]

Did you ever contact Radical Firearms regarding the rifles inability to properly lock the bolt back and properly run steel? I hear their customer service and warranty is quite good, I’m curious what Radical would do for you. Just picked one up, I don’t plan on running steel as I’d like to save my casings for when I learn to reload. I see people suggest upgrading the trigger and BCG. I’ll have my $400 budget ar, I’ll learn what I like then I’ll spend $1,000 on a solid ar.

[@wyominggunproject]

No I didn’t contact Radical because I did a full review of this rifle on my channel and discovered what the issue was. 🤠

[@RL69420]

@@wyominggunproject hey awesome I’ll have to find and watch it!

[@hiking4freedom]

Very informative video. I purchased the RF 300 blackout (nonpistol type). Have you done a review? if so, thoughts etc..

[@wyominggunproject]

I have not done a review on the pistol but if you want to see a full review of this rifle it is on my channel.

[@michaelmikeymichaels]

Well just finished reading all the comments. Most entertaining! Cool video Matt. Informative and had me chuckling. One more thing, just a suggestion but maybe an oven mitt in the range bag might be something to consider!

[@wyominggunproject]

That oven mitt might just be a good idea. 🤠

[@silverback1458]

99 percent chance that the problem is simply a loose gas block or bcg key loose. That's most cycling issue problem. The extra suppressor gas compensated for the loss of pressure from a loose bolt in the gas block or bcg key. I've chased various issues over the years. What I've learned is invaluable. I'd much rather invest in the technical aspects of firearms opposed to gucci rifles any day. You MUST know how to diagnose and fix your issues yourself. If shtf, you won't be able to take it in for repairs or ask a gunsmith. Every man for themselves.

[@Chicano_pistolero]

I had similar issues with a cheap PSA a few years back wth a BCM bol carrier group, turned out the chamber was really rough and after a good polish ran like a sewing machine

[@idexxyy2511]

Funny thing is the RF-15s bcg trigger cutout is compatible will full auto lowers. Usually they’re shortened to not allow the depression of the second sear face of any full auto fcu . But these things are quite literally full sized for full auto trigger sears to be depressed which is very interesting at hand and also logistically versatile.

[@TheJames762]

Possibly, until it's broke in really good, you could use a lighter buffer weight or lighter buffer springs when shooting the steel cased ammo.could also be that the gas block set screw is loose too.

[@fleetman2021]

Mine had over pressure. Blew the bolt lugs off ruined the gas system and barrel. They blamed the ammo saying it was Winchester 556?? Ammo fault the rifle blew up? Had to mortar it to get the bolt free. Any opinions or ideas?

[@adamrodgers2377]

I have had some issues with some Winchester ammo having the Bullet get setback on loading.

[@georgiavol1602]

Have that rifle and haven't had any issues as of yet, but I also never tried steel. Thanks to your video, I know not to waste my money on it. Thanks! I will stick to brass.

[@maxmaxwell4774]

It's under gassed which is why it likes the hotter ammo. More back pressure which helps cycle the action. I would send it back to radical firearms or have a gunsmith change out the gas block, probably fix all of the issues

[@williamrogers.]

I have a feeling that you saying that it's just OK is confirmation that it does its job, and with a little tuning can be relied on in a pinch. That's the kind of honest review that I can take to the bank, and why I'm now a subscriber.

[@wyominggunproject]

Thanks for the watching and thanks for the sub. Full review on this rifle coming soon. 🤠

[@williamrogers.]

@@wyominggunproject Looking forward to it because I just bought one as a truck gun.

[@RogerRoger503]

You got my sub brother. I have a radical and mine didn't shoot steel at first. I needed to shoot 3 mags of brass first(to break it in? Maybe??) But since then it spits out everything. I use Gen 2 pmags and the steel Korean mags.

[@morenoja22]

😂😂😂😂i agree with you bud "but stan try to understand, why are you so mad" LMFAO

[@wyominggunproject]

🤣🤣🤣

[@SparkyOutdoors]

It's definitely because of the gun not being properly oiled. I recently bought a RF-15 and i don't normally do it but for whatever reason i decided to skim through the instructions and it says that the rifle doesn't come pre lubricated and they advise you do so before ever putting a round through it. Mine even came with a packet of lubricant. I'm not saying you didn't but from the looks of it in your video, everything looked pretty dry

[@forgottenprophet0]

My RF is a 7.62x39 model and the reviews all warned me against steel ammo too. For my model it seems to be a firing pin issue instead of gas pressure. Also the magazines they included with my model were 10 count and don't feed properly but if you get a bullet in the chamber it fires real nice.

[@edwardlane9628]

Yes, certain firearms don't like steel. Some need to be broken in before the firearm will use the ammunition without an issue. With the bolt locking back issue might be another problem: gas, bolt carrier group, and or bolt hold open assembly.

[@unalignedforceusers6616]

Hello I appreciate any advice in advance for someone with a tight budget .. looking for an upper receiver in the radicals price range , what would you recommend? And if you had the choice of uppers of Radical or possibly Del Ton ? What would make it as a workhorse is really what I’m asking Thank you again for any advice

[@wyominggunproject]

I’m know a lot of people sh!t on PSA but I have a few PSA uppers and they seem just fine. PSA sell complete uppers for $229. Maybe check with them. 🤠

[@unalignedforceusers6616]

@@wyominggunproject thank you and keep up the great videos!

[@davidk1579]

I don't know what year your radical rifle is but I did read an article about they were having a problem with the bolt remaining to the rear on the last cartridge shot and it was due to the buffer spring not being the right tension and has been corrected I have a brand new radical rifle and it works perfect steel our brass. Thanks for the video. I also have a Ruger 556 which is 750.00 and my radical is built every bit as well.

[@andrecullins1792]

What red dot do you have on the radical arms ar15? I just got one.

[@wyominggunproject]

Vortex Crossfire

[@reevesc87]

Is that a Sig romeo 5 red dot that you're using? How do you like it?

[@wyominggunproject]

That is a Vortex on there. Not sure which model.

[@alanm6113]

So it shoots brass, can you group your shots together with brass? If so, why is the 3k better? If the 400 and 3k will put shots in a good group, why is one better than the other?

[@harryrivas6153]

Never had problems out of my radical, but never tried running steel. Its my only AR, i know i need to get me a higher built AR. Thinking bout a m&p 15 i guess im part of the cheap guns group lol thanks for the review you got you a subscriber

[@wyominggunproject]

Welcome and thanks for the sub. No dude. You are not a part of the Cheap Gun Mafia. You acknowledged that you have a rifle that is budget friendly and “good enough” but not “just as good” as a higher end rifle. The Cheap Gun Mafia are the delusional people that think a $400 AR is “just as good” as a $2500. Please go watch my full review of this rifle and my video titled the “The Cheap Gun Mafia and the Cult of Colt” and it should explain everything. Thanks for watching and for the comment man. 🤠

[@ulyssescisneros3044]

Have you tried to change Buffer and Spring.

[@wyominggunproject]

No sir. Check out my full review it turns out it is under gassed.

[@Hardestway]

I have all kinds of low to mid tier rifles. I have currently two radicals. I know a bunch of people with them. They are awesome for the money but it and miss. It’s a $400 rifle everyday that is very upgradable. You can’t compare RF15 to mid to high end rifles.

[@MindOnBiz]

I got about 800 rounds of steel cased ammo through mine and have had 0 malfunctions. I haven’t used any brass cased ammo at all

[@wyominggunproject]

Check out the full review I did on my channel. Rifle is under gassed.

[@troydorame890]

I am glad to see that you're not bitter😂 I own a radical firearm and yes, I have the same problem. It only likes brass.

[@wyominggunproject]

You should watch the full review I did on the rifle. I think we figured out what the problem was and I think it is OK.

[@richardhealey8057]

Did you make sure the gas port is aligned correctly

[@jesuschristhomeslice9492]

Had a Ruger AR556. Same exact issue, hated steel case.

[@Ja2808R]

One thing I noticed right off the bat was the ejection pattern. The Radical was all over the place and weak. While the DDS & SCAR all ejected seamlessly in one neat pattern.

[@wyominggunproject]

Yep

[@joshualund4876]

I have a 9 mm pistol that I picked up a box of steel cased ammo for and it was like the second box thru the gun, it choked on the steel, but it’s been 100% with brass. Been meaning to find a box of steel cased to see if it runs it any better now the gun is broken in

[@harrisonpalmer7078]

Some guns don't like steel. Some can be picky about mags. Dudes weird

[@rickyrios3089]

The same thing happened to my Walther PDP 9 mm I had some steel casings and it would jam every seven rounds

[@dmitrykarkov4747]

I got sick of so many problems with cheap crap… now I only buy premium stuff. Difference is HUGE

[@wyominggunproject]

Yep 👍🏻

[@t.g.c.trivigunchannel2512]

hey what optic are you running ?

[@wyominggunproject]

A Vortex. I don’t remember which one.

[@davidfisher12865]

The mag that came with mine I threw in a drawer, I run m3 pmags. Never had any problems with m193 and m855. It's pretty gassy, like the military m16s I remember. Too much is better than not enough Carbon up the gas tube, some is better than none. If you can afford a Daniel defense right on, but if you have bills to pay and kids to feed.

[@wyominggunproject]

It’s not the mag. I did the full review on this rifle and I think that we determined that it is under gassed.

[@xforce708]

Hey, I was just wondering what your thoughts are on Radical arms? 😳

[@wyominggunproject]

🤣🤣🤣

[@carlsykessr]

I have had ammo problems with tula in my 1500.00 ar15

[@american236]

FACTS.

[@markhaney9213]

I had problems with steel until I bought a bore brush. Cleaned up with a bore brush and never had an issue since

[@TheTacticalLlama]

why didn’t you run it with the DD mag and steel ammo. I realize it might have been irrelevant but that seemed to be the one thing you didn’t do. Also it putting the can on almost guaranteed it would shoot it.

[@tw8126]

Dude…thanks for this video! I was JUST about to get one…even though my buddy ordered me a Springfield Saint Victor AR for $600. I’m not a gun guy…but don’t want to buy crap that won’t work just to save $200

[@justinmurray4652]

Steel extraction pattern was definitely leading towards weak and under gassed.

[@Steelcity77]

Lifetime warranty. If you're unhappy with it, send it back. Is it even broken in yet?

[@wyominggunproject]

Did you even watch the video? When did I say I was unhappy with the rifle. It doesn’t have as much to do with the rifle as it does with the Cheap Gun Mafias reaction to the short I posted. It has to do with the Cheap Gun Mafia trying to represent this rifle as something it is not. Thats what the video is about. It’s about me posting a short of me firing the rifle and the Cheap Gun Mafia losing their shit.

[@Costanza2014]

I was curious about the gas system, it seemed quite sluggish with the steel ammo. I won't defend Tula because out of a Bear Creek Upper I had one where the primer was punched and it never went bang out of 200 rounds. I am glad you tried the suppressor to prove the issue....

[@atachardware826]

Unfortunately, Budget brands just need to be tinkered slightly. Ignore the Key Board “experts”

[@tsafa]

It's not the ammo. The gun is under gassed. It's ejecting at 4 and 5 o'clock. The most likely culprit is that the gas block has slid out of position. Take off the rail and check to see if it's all the way back against the shoulder. Or not rotated Radical firearms and most budget companies over gas their guns so that they specifically will shoot Tula because they know that's 99% of what we shoot. If you keep shooting that gun eventually will stop working altogether as the gas block keeps moving out of position. Use red Loctite on the screws. This is a quality control issue for sure and I have experienced it myself with Radical Firearms. Once you fix this, you will have a reliable gun for $400.

[@wyominggunproject]

You are correct sir. If you go and watch my full review we did determine that it was under gassed.

[@tsafa]

@wyominggunproject thank you for getting back to me and verifying.

[@davidmarcey7970]

I was just about to order one of the radical arms from an online retailer but I happen to run across one in a local gun shop and got to pick it up and look at it and it was without a doubt the worst fit I've ever seen between the upper and lower a complete rattle box they had an even cheaper Anderson that was wayyyyy better. I'm probably gonna juzt go psa or maybe Anderson

[@wyominggunproject]

Those are probably better choices. 🤣

[@JonFox-t5x]

I just bought a Radical last week. Mine has a great fit and finish. No problems so far. Steel case ammo isn’t available in my area but I always prefer brass case ammo anyway. By the way, the trigger was 4 1/2 pounds right out of the box. The reset is immediate. I only paid $387 for it.

[@JonFox-t5x]

I just bought a Radical last week and compared it to an Anderson in the gun store. The Anderson was gritty and finished poorly. The Radical was smooth and the fit and finish were spot on. So I bought the Radical for $10 more. $387.

[@ExcelleratedOG]

I'm an inventory Marine. From day one and boot camp when you're issued at M16 one to learn how to drill, you learn to shoot later, you're drill instructors throw those weapons all over the squad bay and treat them like trash! Then we take those same weapons out to the range that a hundred other recruits before us did and zero in and hit target. Those cheap gun mafia pogues Don't even know how to properly judge a weapon. If you can send 7, 30 round magazines back to back without stopping and that barrel doesn't melt. I'll take it! All this lube cheap ammo yada yada either the weapon works or don't. I've never owned one of these but I would hate to think them being made out of Texas that they just don't work lol...

[@johnnylang2271]

Wish i could afford a scar or a Daniel Defense. I like my Palmetto state lower with my Bear creek Arsenal upper. Its chambered in 7.62x39. I do run steel through it. I run steel cuz im poor. Does this make me a member of the cheap gun mafia?

[@wyominggunproject]

No the Cheap Gun Mafia are the dumbasses that come into the comments section and claim that they are getting higher end AR-15 performance in a $400 AR. I have several PSA guns and I like them alot. As long as your AR is working fine you should enjoy it. You are not in the Cheap Gun Mafia. 🤠

[@johnnylang2271]

​@wyominggunproject I've never had the opportunity to shoot any top shelf ARs but I did just aquire a DiamondBack DB10. It's my first 308 and I must say I enjoy it.

[@wyominggunproject]

@@johnnylang2271 it took me years to be able to afford the higher end stuff. I have a lot of budget firearms that I enjoy. So shoot the hell out of those guns man. 🤠

[@kylejohnson1308]

​​@@johnnylang2271I have a Diamondback AR with the 223 Wylde barrel in it. Runs great. I think you'll love your Diamondback. May I ask what you paid for that 308 ? I've been thinking of getting an AR pistol with that length barrel.

[@nashdill7919]

The best way to keep your bolt lasting longer is to use the thinnest motor oil you can find, a friend from the military told me that trick because that's what they use to lunercate their arms while in the feild

[@jeffpotts6187]

This issue sounds like you have may a stiff buffer spring and/or a tight-fitting bolt. Two issues that go away after the gun has had a bunch of rounds put through it. Which begs the next question: how many rounds were put through the other rifles that were used to compare the performance using steel ammunition? Because if there is a significant difference, it wouldn't be a fair comparison. And, when it comes to springs, I remember once when I was given a Glock mag whose spring was so tight, you couldn't manually feed ammo into it. So, this type of stuff even happens with large, reputable manufacturers.

[@wyominggunproject]

Go check out the full review I did on this rifle. I think we determined it was a little bit under gassed.

[@DavidRoy1]

I've owned a DD DDM4V7 and a Radical 300 BO. I found out Radical was here in Houston, so I brought it to them to have the see and tighten up all the screws that were falling off. If your comparing cheap guns, The Radical is better than the ATI Omni Hybrid Maxx for sure, though. In my opinion.

[@wyominggunproject]

I absolutely agree that RF is much better than ATI. This wasn’t so much about Radical Firearms as it was about the Cheap Gun Mafia thinking they got a rifle “just as good” as a DD or an LWRC for $400.

[@UnchainedFathers]

I brought mine as a build gun.Bcm bcg. FN CHF barrel. Bcm lower parts kit and buffer tube. Kept it under 1200 with upgrades. People it is an okay gun but like he said you have to do some upgrades to bring it to the standard. Would I have trusted it with my life before maybe, I personally didn’t have any issue before I upgraded it after 2500 rounds. But now after I upgraded it with the important parts I sure as hell will. Don’t expect to get a duty grade rifle at 400. Can it happen if radical gets their QC tight sure but just acknowledge that.

[@dawitkbethel5849]

Buffer tub issue?

[@wyominggunproject]

Under gassed. Did the full review and came to that conclusion.

[@bignick47331]

Idk about steel ammo but I do know my radical had feed issues with the included mag and no issues on other mags

[@Mustyplatypus06]

I’ve got a radical rpr which is the smaller hand guard and I’ve got a bcm on a psa lower. The radical definitely requires more care than the bcm to run but I’ve put plenty of pmc X-tac through with limited issues. 3 light strikes in 900 rounds. The metal mag though doesn’t get used. I’ve tapped it up into the chamber and jammed it up and after that haven’t touched it

[@RageQuit003]

Thank you YT, for recommending this vid in my feed. The mag is an E-Lander btw. As the creator of several popular RF videos, I listened to this while working and had a smile on my face the whole time. Love the sarcasm! I also have dealt directly with Phil/CEO of Radical Defense(DOD division of Radical Firearms). I don't bother making response videos, because I just reply to comments directly(so I know they'll see it). I do love how commenters don't research and think that's the only gun you own. I too have shot the SCAR 16s, but not a Tavor. Two other X95's though. All my Radicals shoot steel. I can even see the armchair commenters in this videos regurgitating their misinformation. If it's short stroking, then you've got a gas problem, a friction problem or a resistance problem(ie buffer/carrier/spring weight issue). Epic rant though. Usually what I tell people is if you don't upload, then you've got no credibility. Evidence or it didn't happen...everyone has a phone camera. Don't give me that 1,000 rds/week b.s.

[@wyominggunproject]

Thanks man. Just subscribed to your channel. You are exactly right about these people that say stupid crap. They are too scared to get into the arena and make videos. They would rather sit back and talk crap. I wasn’t even shitting on Radical Firearms. The point of the video was to point out the Cheap Gun Mafia’s hypocrisy. Radical Firearms is good enough and they don’t make any claims about being “the best” its the Cheap Gun Mafia that will shit post all in the comments talking about how it is the “best” rifle ever and they got a rifle “just as good” as a BCM or and LMT. No they didn’t. They are dilusional.

[@RageQuit003]

@@wyominggunproject They certainly are. You're providing a data point from your sample. You're not trying to justify anyone's purchase.

[@definitelynotthea.t.f.8813]

My bro bought one of these. Would not run for shit. He ended up replacing the barrel and swapping for a Ballistic Advantage I believe.

[@DesertTactical]

Noted. I’ve had my RF AR15 for a couple yrs now and its been running great. I ran a couple hundred rounds of brass before running steel and it has been fine with both. Am I defending RF and discrediting you? No. Absolutely not. I’ll be neutral. You have very valid points nonetheless. Simply stating MY experience with MY RF AR15. Try some more brass then some steel. A lighter buffer weight or a different BCG. I know… you shouldnt have to do this on a new item but hey Ive had high end stuff both break on me or come defective out of the box… so theres that… good video! subbed!

[@wyominggunproject]

Thanks man. You have very valid points and I appreciate your comment. I just finished filming the full review of this rifle and I have had a better experience with all brass 5.56 ammo. Thanks for the sub man. 🤠

[@DesertTactical]

@@wyominggunproject good content too. Ill be checking out your videos!

[@Johnny-jr2lq]

Okay can the 400 dollar gun be turned into a go to war rifle???? Or is it just a pos for ever. I also want to note I think rifles are being built differently. Your high end rifles are I’m assuming 6 to 8 years old. With silencers becoming more available to the public. Manufacturers have to accommodate for that fact. 2 years ago all you would hear is this budget gun is WAY OVER GASSED it gonna beat its self to death. So you have to take that into consideration maybe? Idk the AR platform has been around for a long time. You would think any company could make it and sell it for a reasonable price.

[@wyominggunproject]

You can probably turn a $400 rifle into a GTW rifle but at that point it would cost just as much as a Colt or another higher end rifle. But it definitely can be done.

[@Johnny-jr2lq]

@@wyominggunproject see I think that’s a part of the conversation as well. Yes your correct after investing money on parts you could say well why didn’t you just get a factory built rifle. The answer to that statement is everyone’s financials are different. For some people it’s easier to purchase better parts one piece at a time. Effectively stretching out the cost while still being able to train and enjoy their investment. I guess when people get all bent out of shape about their budget rifle. They are defending their own personal economic status. And that works both ways guys with expensive factory built use them as a way to “peacock” or show off their financial position. It’s definitely something that’s always going to happen rich vs poor have vs have not. Sucks but I guess that’s just the way it is. I suppose that there is knowledge in pointing out the fact. That a budget rifle isn’t as good as a high dollar factory rifle. And to be honest I think people should learn to stay in their own lane. I can mention a few times I was trying to make a informed decision on purchasing something. And the just as good community lead me to purchasing something that indeed wasn’t as good. And cost me time money effort when I could have just spent a few extra dollars and got the quality product. With that said those situations aren’t as prevalent as the opposite. But when it happens oh man is it annoying.

[@blackicekck9family379]

Who shoots steel case you need out of ar that’s not 762. Maybe open up the gas block ? 1:42

[@konaboss83]

Atleast for the 7.62x39 radical firearms they reworked the firing pins so the hit the harder primered steel cased ammo harder I dunno as I don’t have one but support helps I believe they call them the enhanced firing pins but I don’t think the 556’s get the enhanced firing pins

[@jarhead6153]

I totally understand… pre pandemic I bought a JSE Surplus upper for around $300, and it shoots like crap and brass gets stuck in every other shot. Good points made…

[@wyominggunproject]

I appreciate the comment. Thanks for watching man. 🤠

[@adamrodgers2377]

Damn, That is a old SCAR!!!! I wish I had bought one when they first hit the market. I was lucky to get in on the KAC SR15's sorta like you did your SCAR and I bought 2 then I had to buy one later on down the line for my Daughter. Im like you are, I have high end Firearms and Affordable Firearms. In my opinion, and its only worth $0.02, but if someone wanted a good affordable AR I would suggest S&W, Diamondback DB15, or PSA. I have hurd so much about Manufacturer's like Radical, BCA, and that Gawd ALFULL Plomer AR, I cant remember the name of that POS, but Hell PSA has there Premium AR's with FN Barrels go on sell all the time.

[@dependablekit5500]

I've had cheaper firearms and I've had very expensive firearms and the facts are 1 my 650 dollar Smith and Wesson seized steel case in the chamber every time I tried if I ran brass case it was flawless the 1 bearcreek I owned printed 5 to 6 inch at 100 yards I then bedded the barrel and I got it down to 3.5 inch my Ballistic Advantage barreled upper printed 1.5 with 55 m193 the cheap upper receiver had issues with steel magazines my Daniel Defense would run anything steel brass steel magazine or polymer and 0 problems my 16 inch Geissele printed 1 inch groups and zero problems with anything it literally was perfect and I truly wish I had it back however my 1 and only AR15 that I have has the new Rosco chrome lined barrel and I went with Matrix Arms and they produce high quality receivers and my new rig is not only accurate but runs everything and 0 problems but I also have 2400 in the setup and I just have to say you are so right hands down if any of those just as good guys actually got to own or run a more expensive setups they would agree the quality is actually feelable and seeable great video!!!! So over the target lol

[@michelleclark181]

I bought one in 2022 and over paid, even ammo was high at the time. Bullets was $1 a round i think. I paid $800 or $900 after tax.

[@jameslalley3787]

Looks like a gas issue! I own a Radical and mine runs great! But I don’t run anything but brass through it! I appreciate the heads up on the steel casings !

[@wyominggunproject]

You are correct sir. Go check out my full review of this rifle and it shows up there and I figure it out.

[@jeffmagdits465]

True, but I'd had no issues. Send this to radical and figure it out . Most of us don't 1500-3000 grand to pay please recommend a budget AR.

[@wyominggunproject]

Please go and watch my full review of this rifle that just dropped. It should explain some things. 🤠

[@cobia224...]

While you obviously are fired up, I have an RF 7.62x39 upper 10.5 inch, no issues, fires steel all day.... . Many manufacturers will not guarantee their guns will shoot with steel ammo.... Take a chill pill WOW

[@wyominggunproject]

I’m cool bro. 🤠

[@Chickenfriedstek]

In my experience cheaper guns do have more quality control issues. Many work great but there are more lemons on average. But Daniel defense, BCM, etc. Can have issues also. Just less likely. Measure everything for spec regardless of price.

[@wyominggunproject]

Exactly 👍🏻

[@JR15A2]

The cheap gun mafia is pretty funny. jUsT aZ gUud!

[@kaotickustoms]

Definitely an under gassing issue.... especially if it runs fine with the suppressor! Open up the gas port just a bit and it'll run fine! Had the same problem with my radical AR and a Smith & Wesson 7.5" AR pistol....opened up the gas port a tiny bit on both and now they run flawless! 😁

[@wyominggunproject]

You are correct sir. It is under gassed. You will see this in the full review coming soon. 🤠

[@kaotickustoms]

Can't wait to see the video!!!

[@fenrisgaming8982]

I'm not that mad at any AR that isn't handling steel cased ammo simply because the platform itself isn't designed for it. Some may handle it and some may not and I don't think it necessarily comes down to the quality alone..... That being said, Radical isn't exactly at the top of the heap even among budget ARs, You still have some great budget options from PSA, Ruger, Diamondback, and S&W that are a good step above Radical. I'd still be happy to own one, and wouldn't mind giving it a little TLC for the things they "forgot" to do. It's hard to be mad at a $400 AR unless it was just a complete lemon.

[@northsidechrishtk1243]

Just got mines today I hope I don’t have these problems

[@bobg.3206]

The only issue I've ever had with the magazine is if I bump it into the gun too hard, it goes in a little too far, and the gun won't cycle. Other than that, it works as well as any of my other mags. I've never gone the budget route on ammo and I want to reload, so I don't know how mine would do with steel. Mine ran great out of the box, and I haven't had any issues with the gun. Nothing loose, no problems anywhere during the cycle. A well-made gun. I heard that Radical had some QC issues in the past, often involving components purchased from other manufacturers, and those issues had been resolved. As I said, mine ran out of the box, so I can't speak to QC, and I have never looked into it too far. I had other guns that needed to be broken in before minor malfunctions worked themselves out. Sometimes, it was as simple as some oil; other times, it took a few magazines before things ran smooth. I'm a long-range bolt gun guy. I would have never picked one up if I had to pay more than $500 for an AR. Now that I have one, I love it, but I'm not going to drop Daniel Defense money on one, and you are the first person I've seen who likes a SCAR. I'm happy for you. There are lots of reasons why some guns won't run at first. I've just seen too many people in love with their Radical Firearms ARs to believe paying $400 is the problem.

[@GenericBrandDan]

It's not uncommon for any AR, expensive or cheap, home built or baught, to need a bit of a break-in period before cycling steel cased ammo reliably. If it still won't eat steel after a few hundred rounds of hot brass then check gas rings, buffer weight, recoil spring, extractor spring, and gas block alignment....

[@donwyoming1936]

Not all steel cased ammo is equal. Barnaul is the only Russian factory that makes quality 223. The rest is underpowered and not particularly accurate in most rifles.

[@triggerbarPhD]

I have a radical arms. But I also have a Daniel defense and a Geissele. I know what I have and what I don’t have. 😂.

[@wyominggunproject]

Exactly.

[@leoguy1609]

Never fired a Radical Firearms AR15 and had to return my Daniel Defense DDM4 V7 for service. Expensive doesn't mean good and cheap doesn't mean bad. Both Anderson Manufacturing and Diamondback Firearms make decent budget friendly AR15 rifles. Worst AR15 I've shot was made by Bear Creek Arsenal.

[@wyominggunproject]

Agreed. But this video came about because of all the screeching about a short I did where the rifle failed of the very first round fired.

[@waterhead1359]

You missed a good opportunity, if you could get them , should've used anderson and psa to compare. Yes the FN is overpriced good but overpriced.

[@gduquemin]

To be fair I’ve never seen steel cased ammo for much cheaper than brass, I just buy brass bc it works in everything

[@wyominggunproject]

Not nowadays. But it used to be ALOT cheaper back in the day.

[@brianhowell8117]

I used my radical yesterday for the first time and a miss fire for me too but after that it was good to go

[@chadlee5905]

Your rife is under gased with the under powered tula ammo. Lighten up the buffer spring or buffer weight. Or get adjustable gas tube or run full power ammo. you need to brake in cheap guns hope this helps. Don't hate on the pors cheap rifle you trained with better than expensive one you dont

[@LocalFloridaMan24]

Bro took it personal, I like it 😂

[@Krispy74447]

Its definitely a gas issue. I dont remember the exact specs but a previous commenter was spot on. People say cheap guns come under gassed but i believe it's the original gas port spec from the 60s. Modern "high end" rifles come over gassed for reliability. They can push past more fowling and carbon build up. As far as steel ammo goes, steel is too stiff to fire form to the chamber like brass does. So you get slight bleed off on top of already under gassed gun. Brass seals inside the chamber so preasure isnt an issue. I have a couple radical rifles and also a daniel defense. They are not meant to compete with each other. The radical wasnt designed to handle the riggors of battle day in and day out. Its still a great rifle. Makes a great ranch, coyote, just shooting random stuff gun. On a different note, i dont understand the concept of people pulling a rifle out of the box and not lubing it. "Why should i have to?" Thats like buying a car and never changing the oil. It comes prelubed from the factory right. Most firearms ive come across do have some oil out of the box but it's meant for corrosion resistance not operating temperatures. A couple of the first things anyone should do is inspect the gun for any issues and properly oil it in my opinion. Anyways just my 2 cents hope everyone stays safe and happy shooting.

[@wyominggunproject]

Your comment is spot on and that was my point throughout the video that the Radical is OK but the Cheap Gun Mafia will absolutely shit themselves if you criticize a budget firearm. I did a full review on this rifle and you are correct it is a gassing issue. Thanks for the comment sir and thank you for keeping it respectful. 🤠

[@bradd8383]

Something in the gas system isn't right.. BCG gas key loose maybe gas hole isn't lined up with gas block or change gas block to adjustable gas block , i think they make less constricted tubes to

[@workinmanworkinman3889]

Hey would you consider the Ruger 556 ,and the Zavier made down here in Florida as cheap AR 15 rifles platforms????

[@wyominggunproject]

I would personally consider the Ruger 556 a mid tier and I’m not familiar with Zavier. I don’t want to comment on something I don’t have any hands on experience with. Thanks for the comment man.

[@workinmanworkinman3889]

Your welcome, and thanks you’ve given me more than enough information. Yeah the Zavier firearms company is here in Florida it’s a fairly new company, but you can watch reviews of it on KZbin just typing in…

[@wyominggunproject]

Will check them out👍🏻

[@workinmanworkinman3889]

And thanks again. I just hate when someone who is supposed be some so called expert i’m speaking about those comments you showed me on the screen from some people. For you putting them in their place with a real visual…. 👍🏾👍🏾👍🏾That away again to you guy….

[@workinmanworkinman3889]

Hey. Dude, me again. I just wanted to get your opinion about the kel- tec RDB bull pup 556/223 rifle, and I know it’s not what you would consider in the cheap gun mafia category…

[@jonathanspaar8709]

Well said and quite entertaining!

[@rickneuman4467]

I was told that steel case ammo will void the warranty, but that’s what my gun dealer told me.🤷🏼‍♂️

[@wyominggunproject]

🤷🏻‍♂️