Replace exhaust fan motor. Work preformed in this video is by a licensed contractor,and is for trained licensed professionals.
Пікірлер: 36
@BillyKnoth9 жыл бұрын
I work on a nursing home...and they never say change the motor....they are always like just change the whole thing...lol...I have never had to change a motor in a fan like that... I learned a lot from this ....thanks
@NorCal-refrigeration9 жыл бұрын
If there looking worn out, ill do the same get a new one,
@leanorlando9 жыл бұрын
That looked like fun. Great job replacing the blower motor.
@NorCal-refrigeration9 жыл бұрын
Thanks
@baylifehvac9919 жыл бұрын
I always wondered how to change thoes motors. Great viedo
@carloscaballero50019 жыл бұрын
Nicely done! Thanks
@andygalindo89787 жыл бұрын
That was great learning. Thanks for your time i learned a lot. You made that look easy .
@NorCal-refrigeration7 жыл бұрын
Andy Galindo your welcome.
@projectme27025 жыл бұрын
Great video. How would you adjust amp draw on this type of motor?
@hardcooling9 жыл бұрын
I like to fix other stuff then just refrigeration keeps work interesting .. cool vid bro
@vincents19124 жыл бұрын
Where do you clamp the hub puller/jaw puller to get a grip in order to remove a sticky/stuck fan blade? Thanks
@drummerdem509 жыл бұрын
Great job
@popsmccartney4359 жыл бұрын
Thanks for sharing.
@brandoncherry16514 жыл бұрын
good job !
@ianlois0078 жыл бұрын
how do you wire this motor by removing the speed control?
@Straycurrent9 жыл бұрын
Never worked on one of those before. Looks like the four inner legs which have two screws each would be tricky to reassemble. I gather you have to squeeze the legs as you lower into place? Not a friendly design. Thanks for showing.
@NorCal-refrigeration9 жыл бұрын
I just cave man that stuff back in. Look at me. Just being honest. Lol ahahaha.
@leonardochen60178 жыл бұрын
do you know why the exhaust beaker keep drop/ off?
@HarleyBadger9 жыл бұрын
I couldn't tell, are there drain holes that keep the rainwater from pooling down around the blower wheel? I see what looks like a horizontal drain for use when these are mounted through the wall, but what keeps the water from pooling up in a vertical-mount installation?
@NorCal-refrigeration9 жыл бұрын
There is a drain in there for water & grease.
@tomcat275577 жыл бұрын
I decoded that Morris-code on the roof and it said....replace fan-motor at all costs then prepare for helo lift out... pop purple smoke when ready....
@kurtschulerakaaddiokay289 Жыл бұрын
How bout the part where u swap the motors?
@RobHVAC9 жыл бұрын
Nice vid
@dmtycn3 жыл бұрын
Don'r know how did you pull the wheel out? looks nowhere to set puller.
@lobster10027 жыл бұрын
How did you remove the blade from the motor? My fan blade won't come out.
@NorCal-refrigeration7 жыл бұрын
John L 2 set screws and a hub puller
@lobster10027 жыл бұрын
Nor-Cal Refrigeration & H.V.A.C, what's the hull puller?
@lobster10027 жыл бұрын
Nor-Cal Refrigeration & H.V.A.c, There are a few on amazon and I don't know which will fit.
@vincents19124 жыл бұрын
@@lobster1002 Were you able to find a hull puller that works?
@lobster10024 жыл бұрын
@@vincents1912 i saw it on amazon and put it in my basket but i didn't brought it because i just added some rubber washer between the fan and the nuts.