RC DLG GLIDER Full build and maiden flight. RC airplane building DIY Balsa construction

[@Danburdick-lm5xt]

sir you are an artist and craftsman

[@MarkoRoolaid]

thanks

[@jgme627]

You are the heck of builder, the man of RC👍👍👍

[@MarkoRoolaid]

thanks

[@TomFYouTube]

Great job! Need more built up DLG's

[@kev4354]

Mark another nice scratch build.

[@MarkoRoolaid]

thanks

[@samuelcruz9258]

Volar un planeador o cualquier avión de control remoto después de construirlo, es una gran satisfacción.

[@MarkoRoolaid]

Muchas gracias. me alegra que te haya gustado el video

[@개돼지들-z1n]

멋지다.... 나도 만들어보고 싶다 ㅠ,ㅜ

[@MarkoRoolaid]

안녕하세요 그런데 왜 안되죠? 나는 당신의 일을 정말로 기대하고 있습니다 :)

[@개돼지들-z1n]

@@MarkoRoolaid 여건이 안되서 그냥 보는것 만으로 만족하는중 ㅠ,

[@WillieMcphee]

WOW!! I've watch your build videos and they are amazing.... BUT THAT THROW at the end of this video!! im not a glider guy so i have no clue... al i know is that if i tried that launch we would end up with a pile of broken splinters and hours of work wasted in seconds.. i must say i enjoyed that few seconds of this video the most.. great work as always. :)

[@MarkoRoolaid]

It's not really hard to throw at all. At first, throw weakly and step by step stronger. I haven't thrown that much either, but I always succeed

[@ВоваИванов-г5с]

@@MarkoRoolaid любая металка за 300-400 долларов будет намного прочнее и лучше летать. Слишком хлипкий у тебя

[@MarkoRoolaid]

.😀.😀.😀

[@ВоваИванов-г5с]

@@MarkoRoolaid жаль что ты не хочешь учиться Почему ты думаешь что лучше всех. Любой спортсмен со стажем 1-2 года облетает тебя в хлам пока ты изобретаешь

[@big-smoke-rc]

Nice!

[@MarkoRoolaid]

Thanks

[@EugeneZhukov]

Great video! Astonishing job! But if I'm allowed to offer some advice: 1) Wear gloves: rubber gloves (for glue/epoxy works), kevlar gloves (for cutting, polishing, etc.) Your finger's skin will appreciate it. 2) Use a respirator with carbon filters, especially when you are working with carbon fiber, epoxy, acetone, etc. Your lungs and brain will be protected pretty well. All the rest is really amazing! Good job!

[@MarkoRoolaid]

Thanks for the comment. I will try to follow all these tips in the next projects

[@coverdestroyer3572]

Please make a simple boom versiom, is that good for catch thermal?

[@sidbox]

Absolutely have loved all your builds. Fantastic DLG. I'm in the middle of a CLM Element 2. Hope I can make it as tight as yours

[@MarkoRoolaid]

I wish you success, share pictures or video

[@lucianadrian88]

very nice.

[@MarkoRoolaid]

Thank you

[@jaguarjaguar7903]

A very excellent glider. Please tell me how to cut it into Co2 machine?

[@MarkoRoolaid]

how to cut it into Co2 machine? I cannot answer this question quickly, it requires learning and experience. But the easiest thing is to put the same question in the KZbin search and you will get the answer.

[@marc_frank]

hmm i have 3 carbon tubes sitting here 2x 6x4mmx1m and one 8x6mmx1m what size did you use in this wing? non DLG might not need as much i kind of want to make a 2m electric sailplane with those tubes

[@MarkoRoolaid]

Yes, the 2m project is more interesting and flies better. Simply replace the balsa cone with an motor kzbin.info/www/bejne/naCmmIV_fdFseMU

[@flyingphilipp_15]

hi where did you get the carbon round rods from?

[@MarkoRoolaid]

These are carbon arrows, intended for the bow. Available at any hunting store I believe

[@ВикторПрокопюк-ъ1н]

классная "металла"! Марко, подскажи пожалуйста,в рубанке лезвие от бритвы или родное,стальное? и ещё,какая температура на фене при обтяжке?

[@MarkoRoolaid]

Специальный рубанок, только для бальзы. Лезвие немного толще и прочнее, чем у обычной бритвы. Температура утюга около 300 градусов. Сначала нужно протестировать

[@ВикторПрокопюк-ъ1н]

@@MarkoRoolaid спасибо Марко!

[@UFO_Driver13]

классно получилось, подскажите где покупали стрелы для лонжерона

[@MarkoRoolaid]

Привет Денис С ebay, ссылка здесь www.ebay.com/itm/154195473024?hash=item23e6c43280:g:zmwAAOSwFE5fsPNc

[@thomearle652]

Is a laser-cut short kit available?

[@MarkoRoolaid]

Hi Thom, unfortunately the answer is no

[@MrKeepingitrealau]

Do you have a wing airfoil plan for this? I want to build it.

[@MarkoRoolaid]

Hi, Drawings are here grabcad.com/library/rc-dlg-glider-1

[@TTQWorkshop]

No rudder on a glider…🙈 also you need more down on the “flaps”.

[@MarkoRoolaid]

You are absolutely right that there is no rudder and I miss it a lot

[@daviddavids2884]

at 8:00. the outboard located MASS of the (stoopid) CF leading edges REDUCES the (span-wise) stability of the dom. distribution of mass. stoopid oversized ailerons result is over-control.

[@MarkoRoolaid]

Many thanks David Davids, good comments as usual

[@johnw5154]

Great video but if I can offer some advice.Disc cutting carbon fibre without a mask is very bad for ones health. Abraiding/cutting/grinding carbon fibre is definitely best done out doors and wearing a mask. Carbon fibres act just like asbestos fibres when inhaled. Definitely not worth the risks of lung cancer or plural plaques. I really want to give DLG a go.

[@EMTAx]

HET

[@daviddavids2884]

YOU MANAGED to NOT show the installation of the launch grip pin.!!! consequently, i am left wondering, what sort of SILLINESS was done, there.!!!!

[@daviddavids2884]

at 7:19, not just Gigantic, but FULL strip ailerons. CLUELESSNESS

[@gustavelomack8060]

???????

[@MarkoRoolaid]

?

[@daviddavids2884]

whyTF do you keep using heavy CF, where it does NOT belong.?!? at 2:33, W T F --- gigantic ailerons.! the CLUELESSNESS continues! at 2:47, the DESIGN of a main wing SHOULD INCLUDE a CENTER SECTION.!!! at 3:08, the use of curvy leading and/or irregular trailing edges is NOT RECOMMENDED.! at 1:27, this is a Weird profile.! this is a fact that cannot be 'argued away'. googletranslate

[@TomFYouTube]

Wondering what exactly qualifies you to make comments like this about DLG's you are obviously clueless about them.

[@christophgraf63]

Agree with Tom. You are disrepectful and you don‘t seem to have a clue. Marco knows what he does and he is an excellent designer. I already built one of his planes. What about showing one of your designs?