Rear Block Lift Install - 3rd Generation Toyota Tacoma

[@yaddi3434]

This may help someone doing this. You DO NOT have to remove the wheel and jack up the frame to lower axle and all this. I just installed 3" blocks on my 2017 Tacoma. Literally just remove the ubolt nuts, remove the ubolts, get a floor jack (I used a 4x4 block bc of the height) and put the jack under the leaf spring as close to the axle as you can get and jack it up until you have the clearance you need. I was in and out 20 min both sides total time. Easy easy.

[@LG-yy2up]

Buddy, just keep truck in ground, undo old ubolts, use wheel chocks on that specific tire, jack up leaf spring and change/add new block... The End

[@DigginSoCalOutdoorAdventures]

Thanks for making it clear about what blocks were and how they are installed. I am going to do this on mine!

[@DrivenCompanion]

Glad it was helpful!

[@Ramonperez590]

Awesome job! The best video lift blocks install i could find on KZbin I leveled it lifted my Tacoma 2” on front now the rear , looks awkward for my comfort zone 😜 I’m ready to do it myself THANKS....

[@KM-yh4gh]

Looks great! I actually have a 2001 4runner and only want it to sit a little higher without messing with the OE specs. I will do 2 inch front spacers and 1 inch block in rear. What it did for your truck is perfect.

[@davidnalls8628]

Man, this is so helpful. I was having the exact same issue. Getting that block ordered ASAP.

[@ddjackett]

I have been loving this recent install series. big time inspired with this one

[@robertconstantino2277]

Thank you so much for detailed explanation. I will be doing this tomorrow. Stay safe everyone!

[@Joker-pp7lr]

Thanks for sharing this video bro. Keep on making more videos. Your way of explanation is on the spot. +1 subscriber

[@bcf280able]

I've been considering lift blocks on my 2018 Taco, I have a 3 " leveling kit on the front. But I do need to raise the rear because of the rake. Thanks for the video.

[@markum5094]

I’d give you 3 thumbs up if I could just for being persistent.. very nice stance on that Taco

[@DrivenCompanion]

Would have been easy to just leave it sitting level but I knew I'd always wish it had that rake. Thanks for the encouragement!

[@Dr10Jeeps]

Well done! You definitely know what you are doing.

[@thumperjr100]

Looks fantastic

[@lawdawg_7983]

Truck looks great, I wouldn’t change it

[@jorgenoneya5382]

Was wondering why dint you use both of your jack stands on each side, instead of using your floor jack on the passenger side. I’ve had floor jacks drop on me before by loosing hydraulic pressure. Also did you have to disconnect your ABS bracket for slack or your brake line bracket?

[@DrivenCompanion]

I had the jack stands positioned in case the floor jack were to fail. As for the brake line I did remove the bracket closest to the brake due to the increased height.

[@awynne56]

When I lifted. I had no luck lifting the frame. I ended up lifting from the pumpkin. Then used another jack to lift the leaf spring up till it made enough space for the block. First side took 1:30 hours. Second side took 10 min. Don’t know how you got the leaf to come off by lifting by the frame. I’m I’m running an ome Dakar leaf pack and wanted another inch.

[@LSEtrucks]

Great video was unsure about doing this myself but seeing how easy it is, gonna knock this out! Thanks for the great video!

[@MrTB321]

So putting the block on doesn’t require new u-bolts?

[@billlaughlinjr5460]

Thanks that was a great and informative video

[@williamrickmond9673]

Thank you so much for your clear video and concise speech. Sub confirmed.

[@el.tacolgando]

Looks great. Can wait too do that too mine

[@ST-fk3jz]

Wouldn’t you then also need a shock with a longer eye to eye length?

[@chrisbode1]

Great Video! I am going to install a 1.5 inch on my 2020 TRD Offroad today. Do you think the factory shocks are ok to run with the lift?

[@christiannieves4307]

I have a question, my left side the rim is more Asia inside than the right side, I never got a hold of it, what could it be?

[@eli25jk70]

Is this the same steps for 2nd gen tacoma? I got a 2” RC level in my fron but now it looks squatted 😂 im going to add a 1” block to the rear to level it out.

[@rupindersingh2227]

Good job. Are you using the same ubolt or new one.

[@Daniel-id5kd]

Great video. I’m about to do the same on a second gen. Have you ever tried to do this with Jack stands on the rear pivot point of the leaf springs instead of the Jack up front? Just wondering it they would be in the way or not…?

[@cabbie1106]

What size block is that?? Do u get any axle wrap?? I want to raise my back end a tad I don’t like it sitting stock

[@DrivenCompanion]

1" block. No issues with axle

[@mmunoz5875]

Great video bud!! Can you add that 1 inch block and add a add a leaf to that? I'm going to install a 2.5 Fox shocks that can be raised up to 3 inches and I just wanted to make sure that I get as much as I can when getting this installed?

[@DrivenCompanion]

Yes, I have an add-a-leaf installed already and coupled it with this block.

[@lukelem]

Is the Toytec block billet aluminum? If so how has it held up over time, deformation or corrosion?

[@reidjensen569]

Very straight forward. Thank You. One question. Did the modifications you made to both the rear and the front of your truck have any impact on the ride quality? Did it become a stiffer ride?

[@DrivenCompanion]

Yes, must stiffer than it was originally. Spacer & block maintained the stock ride but the new shocks and add-a-leaf totally changed it

[@AldapesExpress]

Did you need a rear alignment after adding the rear block?

[@713supercars4]

So what exactly are you sitting at in the rear after the blocks?

[@mattmason9688]

How did you get the leaf spring and the axle to separate so easily? I’m having problems with mine. The center bolt that goes through the leaf springs and buts up into the axle won’t allow me to separate the two

[@banegasbanegas224]

My tacoma leans on the rear driver side 1 inch I would like to know if I can put a 1 inch block or 3/4 block to make it even

[@gandtoley]

What is total height for the front? Truck looks good btw!!

[@boosttv5688]

I have the Icon Stage 1. Will this reduce sag when i tow my small camper. JuSt looking to reduce the sag.

[@DrivenCompanion]

Yes, adding height should help it to level out when loaded.

[@eddew8825]

thank for the video

[@michaelcanadezo2629]

So you did a 2 in the front and 1 in the rear?

[@paulc3692]

Slowly lifting my truck up starting off with a front fox 2.5 coil over and a uca. Can I put on a 2”” lift block on a stock trd off road shocks without bottoming out?

[@lgohonolulu3680]

Nice. Were you able to use the stock U-bolts or did you have to get longer ones?

[@DrivenCompanion]

The kit came with new U-Bolts so I used those.

[@TristonBrownfield]

Can you share torque specs you used ?

[@Turtlemilk]

It’s been 3 years since you uploaded this video, any problems ?

[@tylermalmsten3170]

Hey I’m considering doing a 2 inch block in the rear, but would like to use a U bolt flip kit, I wonder if it would work

[@DrivenCompanion]

I'm not expert but it looks doable. Did a quick search and found this page: www.relentlessfabrication.com/products/u-bolt-flip-plates-for-tacoma-springs

[@gjsc424]

Great video!

[@pakanuto1]

I was thinking of installing 1 inch block too on my truck, If I am working on one side can I remove the tires one at a time instead of removing both at the same time? I don't have enough jack stand.

[@DrivenCompanion]

It will be a little tricky to do one side at a time. To get the gap you need on one side you've got to be able to push the axle down which requires it to push up on the other side. Maybe you can find a single point in the middle to support the weight of the truck on your one jack stand (trailer hitch?)... I'd recommend just buying or borrowing a second one.

[@tr4ilblazin]

Yeah you can do one side at a time it’s. Easy

[@js4wd295]

Awesome thank you

[@scottfergusson8411]

Should have installed sumo spring bump stops on it .

[@IAM205ENTERTAINMENT]

Why do some people use lift Block instead of the spacer in the rear

[@vincedprincehowtodiy7705]

I already have a heavy duty rear leaf spring but would still like to raise my back.. you think adding a 2" lift block will be ok?

[@DrivenCompanion]

I don't see any reason why it would be a problem

[@vincedprincehowtodiy7705]

Concerned about the ride quality.. with my set up, do you think i should go with adding a 1" or a 2" spacer?

[@pollo2604]

I have tacoma toyita 2015 3" fron 2" back isgood for lebo

[@Yotapuga]

Did adding the block interfere with the quality ride of icon lift? I have a stage 2 as well and need more rear lift

[@DrivenCompanion]

No, didn't notice any change to ride quality with or without the block

[@Yotapuga]

@@DrivenCompanion did you use the stock u bolts ?

[@DrivenCompanion]

No the kit came with replacement u bolts

[@hirvinferrer8915]

what size tire and wheels are you running? Looks great Mike!

[@DrivenCompanion]

285/70/r17 Duractracs on 17" VTX Rogue wheels

[@thegumuchim]

Would reinstalling the overload leaf do the same as the block? Just ordered the same leaf pack.

[@71tattooguy]

HKD Productions Leave overload in will give more lift.

[@DrivenCompanion]

Agreed

[@ronaldcalawen5541]

If you lift the rear you need an alignment or no?

[@DrivenCompanion]

Maybe not as crucial but probably still a good idea since you're still changing the vehicle geometry

[@judemock2699]

Where did you purchase the bottle jack ?

[@DrivenCompanion]

It's from SafeJack

[@cjanderson66]

did you remove your overload spring?

[@DrivenCompanion]

Yes I did. Instructions said that I should but I'd recommend leaving in place if you want a little extra height.

[@cjanderson66]

Mike C I did a 3aal and my truck felt every tiny little bump with the overload. Installed the blocks and removed overload spring and now it rides so nice.

[@ronyvilleda9292]

What size wheels and tires brother

[@DrivenCompanion]

17" wheels - 285/70/r17 tires

[@ronyvilleda9292]

@@DrivenCompanion thank you

[@torchsupport3546]

Great video! Would love to have you do a video installing one of our lift kits, message if you are interested in working with us. -TORCH

[@terryosowski8143]

One side at a time huh ?

[@DrivenCompanion]

You could also do them at the same time...