Honda Talon Rear Bumper, Hitch, & Snorkel Install

[@f150dan]

I’ve watched some of your videos, but just now subscribed to your channel. I’m the guy in the KRX you rode with at Windrock. It was a pleasure to meet you.

[@CODOutdoors]

It's good seeing you and Lonnie working together, it's like old times! Talon looks Awesome!

[@aaronbingham1535]

Y'all are getting it looking good

[@jpyka4x4]

One day, sxsblog and red beard will colab, and that will be a good day.

[@sandmanbub]

@Whoop!

[@trumpfancardanostakepool4737]

Looking clean. Interesting they use the frame insides as a clean air source.

[@randytravis3998]

the build steps are coming together nice will be a sick ride when done ..

[@GodschildinNC]

Add some red cloth or foam behind the snorkel cap. It will act like. A pre-filter, and see the design.

[@nathannero9338]

I miss seeing your old gshock haha. It was always there

[@RedBeardsGarage]

I love that watch but this one is so handy. I don’t get my phone out near as much.

[@nathannero9338]

@@RedBeardsGarage I bet it does make it easier with your phone. I’m just a sucker for g shocks!

[@acurarl9929]

Take the snoot end tip off an get more intake sound

[@TheBiggestRedneck]

Definitely Should Put A Different Exhaust on it Then That Stock Pipe So It Will Sound Better & A Little Bit Better Performance

[@mrsnicklefrits7093]

And you said those check valves come with the snorkel kit?

[@drmarkintexas-400]

🏆🏆🏆👍🇺🇲🙏 Thank you for sharing

[@jeffjohnson3912]

There’s more comments and more views on the custom builds. I personally like em all but if you wanna keep building and reach more folks do more of your crazy custom stuff! I love everything y’all do. I wanna see more custom Greg stuff!!

[@fax5362]

if you could see this and reply it’d be greatly appreciated. did you happen to dielectric grease anything or seal the airbox off with anything other than the stock seal? really wanting this kit.

[@saephan34]

So the snorkel kit comes with those pcv valves?

[@bryduhbikeguy]

For the rear wheels protection,to just a couple inches inside of the outer edge of them,make a tube bumper that hooks into the 2"receiver hitch and v's up and out like the mounted.People can't run into your tires and bend your suspension.You can remove it when you need the wench.You won't need it with a trailer.

[@genebond]

I'm a little concerned on the check valves. I used fuel filters on mine, for dust reduction. I understood that as the transmission, differential, etc. heated up, the air would go out, and when it cooled down, it'd come back in, since the oil would expand slightly when heated. Also on the fuel tank...

[@platinumdragon9934]

Hi. Do you know where I can find the strut that the bumper slides into? There is one on each side. One of the struts bent on my talon along with the factory bumper. I'm replacing the bumper but also need to replace the strut which I can't seem to find online........ thank you. Great video

[@nikdipetta]

You got any of them duromax discount codes!?

[@gatorglockman]

Where did you get the check valves?

[@nfra1663]

Where is the cross kart build??

[@TheBudman302]

Could have went ahead and did an exhaust swap also while ya had the muffler off. Wake it up, give it some sound.

[@TheBiggestRedneck]

Hellz Yeah I Just Said The Same Thing & They Definitely Should

[@randytravis3998]

he will change it in a build coming up he said ...

[@greggthompson7]

My guy you should paint the rear bumper red.

[@davessparetime83]

Don't tighten those rear control arm bushings while jacked up. You have to tighten them at Ride height.

[@heatherbonomi1779]

Do you have to put the valves on?

[@andrewkennedy1302]

Took the muffler off and didn't start it up?? Disappointing. Haha

[@randytravis3998]

would have tripped a engine code with the O2sensor unplugged .. also could run the risk of valve damage with no muffler