Sidewinder wrap. From mild to Wild!!!!

[@nateruh3698]

looks sweet.nice job

[@rednecksdirtyhands]

thanks! 🍻

[@billyb.9878]

Awesome look. Kinda like a Red Wings look. Yes I'm a hockey fan. Nice sled. You putting a lot work on her. Looking Fer the test run next.

[@kurtruschke8679]

She looks brand new!! Can’t wait to see it!

[@b01tact10n]

Damn! Not a minute wasted whenever I tune in. To bad Yamaha got outta the biz... Im currently getting trained as an EMT where my expertise is Cooking/Baking/Grilling/Smoking, Hunting Gathering, and People. I do have a '14 Jeep JKU Rubicon, but id like to get a 2up possibly a Cat now that im a Cat person for my Lady and I's needs. Great work!

[@davidnielson1960]

You did a great job on that Yamaha

[@rednecksdirtyhands]

thanks 🍻

[@fordman3571]

Great videos,always good to watch. The humor & walk throughs on builds. Keep them coming man. 👍🏻💯 also do you sell those decals "REDNECKS DIRTY HANDS" ?

[@rednecksdirtyhands]

thank you! stickers will be available soon! 🍻

[@chriskonecny7347]

What is that tool you used removing the float pin on the carburetors like a pin punch thing

[@rednecksdirtyhands]

it's a spring loaded center punch. I got it off the Mac tools truck but you can also get them from crappy tire or princess auto. 🍻

[@markcomisky7106]

I like the Yamaha colours

[@timbaker6030]

Is there a way to get in contact with you I watch all your videos, I have a problem that I know you will have an answer for I did a motor swap on a skidoo I took the motor out of my 93 Mach 1 670 and put in in my 97 formula 500 I had an issue with water in the tank but I solved that. So when I took it out of the Mach 1 about 2 weeks ago it was the best running sled I ever had. Now it runs good but if I punch the throttle and hold it it will bog down till it dies and then i have to pull it 20 times to get it to start now I know it is a rich condition because if you prime it while punching it it gets worse I also put my hand over the carbs and it gets worse. It just doesn’t run the same as it did in the Mach 1 it doesn’t seem like it is as responsive as it was before if you hit the throttle it was right now now it will rev up but it’s boggy I am using the clutch from the 670 and the cdi box and coil and carbs all from the 670 I did notice that the motor sits at a lot more angle tilted Forward more than it was before, would this cause it to be rich on acceleration? Also I gave the Mach 1 to a buddy of mine with the formula 500 motor in it and it ran fine but the 670 exhaust had to go with the Mach 1 so I had to use the 500 exhaust on the 670 it is a little smaller but I wouldn’t think that would make it run rich on acceleration any ideas?? I’m stumped on this thing I didn’t think I would have all these issues the sleds has 150 psi on both cylinders and I had to relocate the oil bottle because it was to low so I got it up in the sled and it is getting oil properly.

[@rednecksdirtyhands]

you can reach out to us through our Facebook page RN+DH 🍻

[@darrentoth7165]

I just ordered a graphics kit for my Winder!!! Never installed a wrap before and I am nervous about it as it is a lot of money and I dont want to screw it up, lol!!! 100 & something pieces to apply, something has to go wrong at some point! How long did it take to do yours and were you satisfied with the results? It really looks good in the video!!! Cheers and thanks for the video!!

[@rednecksdirtyhands]

yeah it takes a bit of time for sure! especially the first time ever putting a wrap on a sled!! I think that one took a few hours lol but just take your time and be patient with it and you will definitely love how it turns out! cheers 🍻

[@darrentoth7165]

@@rednecksdirtyhands Thanks! Looking forward to your lake runs, your Winder videos are awesomely the best!!! 🤩

[@darrentoth7165]

@@rednecksdirtyhands Hey there Pete, got my wrap on the o'l Winder.....twas quite the job, holy crap, lol!!! One important thing I learned and would like to share is the "heat gun" is your friend and makes contouring around rounded areas sooooo much easier! All it takes is a quick flash of heat ( not much or you will melt it!) and the wrap will be much easier to manipulate in those non flat difficult areas. It would have helped you when doing that rectangle piece that sticks out the side by the exhaust. I wanted to share the pohos I took of the finished, wrapped sled but there doesnt seem to be any way to add photos to comments 🤔

[@glennturchinski1741]

How hard was it to put on and how long did it take

[@rednecksdirtyhands]

it wasn't too bad to put on, just took a bit of time to figure out where all the little stickers were supposed to go lol. over all it only took about an hour and a half to two hours to put it on. but that was the first wrap we have ever done, so the next time would be quicker for sure.

[@brucepeters508]

do you sell merch!!

[@rednecksdirtyhands]

we will be, just trying to get a website up and get everything together. hopefully soon 🍻