Renaul Megane II . Key programming with Renolink

Рет қаралды 31,823

Күн бұрын

Пікірлер: 72

@gameiro59 2 жыл бұрын

I've already programmed a key into a Megane with Renolink 1.87 EU, but didn't know the tip to let the door open. Last version is 1.99. Thanks for the information.

@YOYODiagnostic 2 жыл бұрын

👍

@darkojankovic6440 10 ай бұрын

Great video man! Very helpful!

@YOYODiagnostic 10 ай бұрын

👍

@dul-boy 2 жыл бұрын

When I try to key programing,i finsh read pin and connect,but on start learning i get-7f3b22 Conditions not set or sequence error...Any help,thanks...

@kaller.9440 Жыл бұрын

If I don't have any cards for the car at all and I get used 3 button cards and new transponders, can I just add them to the car? The only original thing I still have for the car is a transponder, but it is not recognized by the car, so I can neither open nor close it and I cannot turn on the ignition. If I find the cards again, I can turn on the ignition, but there are other transponders in it and I would now get 2 cards with the same buttons from a used car and swap the transponders in the cards and then teach them, I have to do each one Press card on Validate or only when I have put all the cards in one after the other?

@CaptainRuderalis Жыл бұрын

Hello friend, what is your cable(OBD)? Do you have a link?

@kbgaming6012 Жыл бұрын

Does it have to be a Reno link cable?

@kaller.9440 Жыл бұрын

how did you get a connection to the probe? I get rid of the red x but then I get this message Character spacing is invalid and cannot be removed. I just want to read the pin of the cards and then establish the connection for learning and programming and then after that has happened successfully cut the connection.

@LambeLab 13 күн бұрын

Great video! Does this work for megane mk1? I have cabrio 1997.

@YOYODiagnostic 12 күн бұрын

@@LambeLab Hi . Yes

@mustafasmajlovic2676 10 ай бұрын

Hello Interface disconnected by me how did you install that renolink? Thank you.

@patrickshish9262 5 ай бұрын

What happend between 3:06 and 3:09? Im Stock AT 3:06...

@user-xl3cb 2 ай бұрын

secret

@user-xl3cb 2 ай бұрын

way you cut video 0n 3.09 the most important part, how we solve 7F8022 Conditions not set or sequence error

@KalleRenaud 2 ай бұрын

Hello, I did it the way you showed in the video for a Renault Espace 4, the cards were added to the vehicle and the vehicle can be started with both cards, but the central locking and Keyless Go don't work, I have to insert the cards into the card slot to start it. How can I check in Renolink whether the cards are running at 315 or 433 MHz? I also checked the door lock and the internal contacts are working, as well as the motors. I also replaced the sensor and attached new metal mirrors to the door handles, but unfortunately without success. Someone has an idea Best regards Kalle

@YOYODiagnostic 2 ай бұрын

@@KalleRenaud Hi , I believe you have problem with the key, it's not good quality, I'm sure you both from AliExpress and it happens many time to have this problems. Check also the antenna that reads the key signal.

@KalleRenaud 2 ай бұрын

@@YOYODiagnostic I have 2 original Keyless Go cards for my 2007 Renault Espace 4 that came with the purchase. With one card, the case was defective, and I opened it, then I lost the original pill, so I got a replacement pill and a new case. Now I have gotten the card where the chip was missing to the point where I can drive with both cards, but my Keyless Go and central locking no longer work with the card. According to the Can Clip, 2 cards have been read, but for the Keyless Go, it shows 0. How can I now add the maps to the Keyless Go? Can Clip says that all antennas are fine, the strange thing is when I park the vehicle and then after a certain time want to open another door, it only works if I put my hand in the driver's door handle and pull the handle, then you can hear all the doors unlocking, but this doesn't happen every time. When I drive at a certain speed, you can hear the vehicle locking the doors, and you can open and lock the vehicle using the switch in the headliner. It all works, including adjusting the mirrors, ventilation, child safety locks, window lifters, and the light at the bottom of the door. Didn't you also have a video where you explain with Renolink how to assign foreign cards to the vehicle by taking the VIN from the donor vehicle in Renolink?

@yonag5308 2 жыл бұрын

Is it possible to program a new keys when the original one is not working ?

@YOYODiagnostic 2 жыл бұрын

Hello. Yes . You don't need the original key.

@Skinny-me 3 ай бұрын

Hi! Thank you for the video Great stuff I Need to do what you did here on My Scenic2-2005. New (extra) Key. Can you point me to what hardware (OBD2) i need to connect to Renolink1.87? I Have downloaded already, will it work with Win10, or must I use Win7? Appreciate it! Best to you sir! David, Sweden.

@YOYODiagnostic 2 ай бұрын

@@Skinny-me Hi. I have a video dedicated to this programmer. I show you from where you can order the hardware and software, give a search, don't be lazy.

@Skinny-me 2 ай бұрын

@@YOYODiagnostic Not Lazy Sir.. :) Just wanted to prevent bying something that does not work! I found A cable & software 2.10 on ETSY website for 60 Eur! Seems good, so I will go for that

@dusandilove2905 Жыл бұрын

Hello, I menage to program one new china card, but its only work to start a car not key lock. The card that before I use program was opening car ( but not start engine) now stop opening car and not recognise by computer program. Now I have 2card that start engine but no card that unlock car. I tried couple of times to reprogram, but renolink only recognise 2card (one is new) that start engine, but old 1card renolink dont recognise. What can I do to get opening car function back? Thank you

@SamSam-ee3fy 7 ай бұрын

Hello mate I have Renault Zoe 2019 sealed the motor and inverter need’s both programmed to Ecu I have can clip what’s the best way to do it ?or could u do remotely?

@YOYODiagnostic 7 ай бұрын

You need CanClip

@dirtymechanic627 2 жыл бұрын

my open door sensor is not working(the door is closed all the time) and about 2 month ago i programmed a key and there is no problem!

@soptea 2 жыл бұрын

Respect Gabi Gafu !

@YOYODiagnostic 2 жыл бұрын

Hello This is true. Does a great job with this program. 👍

@NorbertM98 Жыл бұрын

That person is actually a scammer with the program. Sells the program to people on different platforms, than charges for the license separately in some cases. I could only get my license via the help of PayPal... The listing had the license, but the software I got with the device did not.

@enerzis 2 жыл бұрын

hi dear friend, i comment you that my cards are disprograming include the original cards. you know how i can re programing my two cards? i have the original cards but this one is deprogrammed.

@kaller.9440 Жыл бұрын

Funktioniert es auch beim Renault Espace IV mit Keyless Go? Muss leider noch auf meine Bestellung warten. Mit dem Renault Clip braucht man ja ne PIN für nen Schlüssel anlernen.

@YOYODiagnostic Жыл бұрын

Ich weiß nicht ob es funktioniert. Ich habe nicht probiert.

@kaller.9440 Жыл бұрын

@@YOYODiagnostic ich werde es Probieren und dir dann Berichten.

@YOYODiagnostic Жыл бұрын

@@kaller.9440 👍

@kaller.9440 Жыл бұрын

@@YOYODiagnostic Hallo, wie versprochen bin ich wieder da. Also du kannst beim Renault Espace IV die Schlüsselkarte selbst neu machen. Ich muss nur noch rausfinden warum die Keyless Go und die ZV nicht mehr über die Karten geht. Auch kannst du deinen Kilometer stand per Renolink ändern, geht über extra und dann Tdb.

@YOYODiagnostic Жыл бұрын

@@kaller.9440 👍

@saifhexprog5885 2 жыл бұрын

good work bro

@YOYODiagnostic 2 жыл бұрын

Thanks 👍

@JosipBasic 10 ай бұрын

Can be just new key added to car, or you need to have all keys present while doing this process? Car is Clio Mk2. This part is confusing me. Thanks for reply.

@YOYODiagnostic 10 ай бұрын

1.You can program keys even if all are lost. 2.Another key can be added even if you have one present, but both must be learned because the old one will be deactivated after programming the new one, for this reason both must be learned.

@JosipBasic 10 ай бұрын

@@YOYODiagnosticThanks for clarification.

@YOYODiagnostic 10 ай бұрын

@@JosipBasic ,,👍

@Irritatedcodm Ай бұрын

@@YOYODiagnostic I have lost all key cards for my Mégane 2, could you explain how to code a new key with no keys available, thank you😊

@YOYODiagnostic Ай бұрын

@@Irritatedcodm ist the same procedure 👍

@charalambosavgousti121 Жыл бұрын

Hi there! is there any Renolink V1.87 software available for free?

@Bezaine 2 жыл бұрын

thank you so much this was realy helpfull

@YOYODiagnostic 2 жыл бұрын

👍

@laurentiubancila7675 Жыл бұрын

What is the obd that you used?

@YOYODiagnostic Жыл бұрын

OBD link

@g____-590 10 ай бұрын

Did you insert new key at first?

@YOYODiagnostic 10 ай бұрын

Yes,it can do all keys lost. If you lost your key, no problem it can program the new one, but use original software from Gabi Gafu.

@EtznabMirror Жыл бұрын

What is the name of the program?

@psheraton81 Жыл бұрын

How to activate hands free on new key ? Is this possible with renolink?

@YOYODiagnostic Жыл бұрын

as far as I know with these cards it should work automatically if you order the right card. If you already have 2 keyless, the 3rd one won't work, you have to delete one from the memory.