Recoil and Carburetor Reassembly. Visit my channel for more repair videos; www.youtube.com...
Пікірлер: 24
@bobgernaat89605 жыл бұрын
What an excellent series. I just finished rebuilding my ms 250 thanks to you. I can't believe how you got the impulse line and your camera in such a tiny space. Well done video! I appreciate you taking the time to put it together for those of us who don't know chain saws.
@greendts12 жыл бұрын
thanks donny, this video in particular helped me rebuild an ms 250 for my brothers company, its 1:00 in the morning and i spent hours scratching my head trying to figure out the switch configuration and in seconds you solved it by saying the metal spring goes on-top of the plastic... you are a legend amongst men!!
@josedejesus61854 жыл бұрын
Hi Dony! Thanks for for the tutoring! Your videos are always a great help. Just an observation, when you install the intake boot, you can wrap a string around it and pulled it thru the casing hole. It is a lot easy to install it! Thx!
@stevesikora12 жыл бұрын
Thanks for the video. I took the carburetor on my MS250 apart 6 months ago, since the saw was running really bad last year. I only put everything back together yesterday, after buying a new carb repair kit on Ebay. After so long, I wasn't 100% sure how everything went back together but your video helped a lot. I put new gas in it, cranked it a couple of times, and it worked right away, with as much power as the day I bought it. Just had to adjust the idle a little. Works great now.
@xdvantx2 жыл бұрын
Very well done boss thank you so much for the time and knowledge it's much appreciated couldn't have done it without ya!!!
@squinteyedmangle7 жыл бұрын
donyboy.I couldn`t start my saw, went to check the spark plug,and noticed a loose wire.2.21 on your video tells me this works as part of the switch and showed me where this should go.Followed your instructions,now the chainsaw works fine.You`ve probably saved me a lot of trouble and money.Many thanks for such a informative video.
@cnj45212 жыл бұрын
Me too.... I'm not sure how that spring thing managed to get around the back! Works a treat now! Thanks very much..
@donyboy7312 жыл бұрын
THANKS FOR WATCHING
@geojor10 жыл бұрын
your videos have pretty well touched on every part of the chainsaw, thanks for sharing your knowledge in a very learnable way...
@mongolioose4 жыл бұрын
Thank you for sharing these excellent videos and instructions. I am VERY grateful.
@dragevo213 жыл бұрын
Great, thanks to your vid I found out how the kill switch arrangement should be like. Now my saw can be shut down without letting it run out of gas, lol. Thanks !
@donyboy7312 жыл бұрын
you're welcome sir!
@donyboy7313 жыл бұрын
@vzarou probably needs a new carburetor rebuild kit
@vzarou13 жыл бұрын
hi i have saw 25 inch shil when i spray crburator cleaner is never work at all what shall i do before what good then when i turn its stop bye self then i pust carburator clean is never running thanks for youif you could help me for problem
@donyboy7313 жыл бұрын
@aaronac8 around .030 usually ok out of package,
@Bassyswing111 жыл бұрын
Its already been said but thanks for showing how the choke switch goes together.
@donyboy7313 жыл бұрын
@dragevo2 you're welcome
@gogossogog27164 жыл бұрын
Very nice video
@donyboy7312 жыл бұрын
goo job!
@topflight23588 жыл бұрын
just bought a used ms250 and i opened it to check the air filter, i saw a tube with a small looking plastic filter... i just saw it on your video when you mentioned "adjusting screw boot cover" looks like its attached to that rubber boot...MY saw does not have that boot, so the filter is sitting in the housing, is this ok or does it need that boot cover to hold it???
@942doc111 жыл бұрын
HI,where would you say do the wires for the coil go,they all have to touch some kind of metal?