Yay, another how to video that the maker puts obnoxious loud EDM over instead of taking advantage of the time by explaining the process and teaching some helpful tips. Thanks?
@Maulana_rhodes5 ай бұрын
Adding a voice over would result in less views because only ppl that know the language will watch it
@adityagadgets81438 ай бұрын
From where did you buy this RC car
@confusedentrepreneur4 жыл бұрын
What board have u connected plz leave a link
@HDXFH4 жыл бұрын
It is a TP 4056 Li Ion board
@OnlyDubai4 жыл бұрын
Could u write in description, about the chip and battery. That will be helpful
@HDXFH4 жыл бұрын
The battery is an 18650 laptop cell and the chip us a TP4056 board
@ashokjadhav99042 жыл бұрын
@@HDXFH thanks 😊🙏
@addythakur7454 жыл бұрын
Leave a link for good cell you used in this video
@ARMTechHomemade4 жыл бұрын
this sell is from old notebook battery
@__-hh3gt4 жыл бұрын
Or from old laptop battery. Thanks to the video maker man.
@magyaradam89572 жыл бұрын
What is that circuit board thing you put on there
@kovalenkoihor43254 жыл бұрын
It's what happens when dad is fucking tired.
@MrGauravmatta3 жыл бұрын
Which battery /module you used.. How many volt battery
@PantelhsTchouxnikas-u1i14 күн бұрын
the best video converting aa batteries to li ion batteries
@richardrmagno21943 жыл бұрын
Can this be done with 2 d batteries
@Alamin3113 жыл бұрын
Hi Friend, I am trickle charging my car battery through Dewalt 20V using LM2596 and it's working really good and have been using it for about an year from now. Now my question is I want to protect my Dewalt Battery from going too low on Voltage and I tried using XH-M609 and LM2596 together but it didn't work. Now what do you suggest me to buy which might help. I appreciate any help please.
@JohnNy-ni9np4 жыл бұрын
What is the rated current of the converter ? Probably around 1A, not enough for the RC car.
@E12DEV4 жыл бұрын
What converter? It does not need any converter, normally this car is powered by three AA battery each of them running on 1.5V, total of 4,5V for car... one li-ion cell is at 3,6 - 4.2V, so there is no need to convert anything. Battery is connected directly to the RC car electronics... That board you see is charger for the battery...
@JohnNy-ni9np4 жыл бұрын
@@E12DEV , Oh I thought you supply the car with USB 5.0V from the converter. So you supply the car from the lithium battery directly. The battery actually have voltage vary widely from 3.0V to 4.2V , so your rc car on average operates at half the power compares to the alkaline one.
@E12DEV4 жыл бұрын
@@JohnNy-ni9np It is not my RC car, Iam just guy walking past this video, and I saw some comments so I tried to help :) And I agree that this is not best way to do it, it would be better with some kind of stabilizer with discharge protection...
@kovalenkoihor43254 жыл бұрын
@@JohnNy-ni9np Actually, 1.5v for alkaline it's when they are fully charged. Usual is 1.35v. And nobody is using alkalines for such a things, because they are drown down very fast. Usualy some rechargeable Eneloops 1.2v, what gives us in total 3.6v. And Li-ion at its 3.7v flat gives much more power. And much more current than any alkaline. I usually do the same thing.
@helijim4 жыл бұрын
@@E12DEV That board isn't just the charger, it's also the BMS and it is current limited to 1A output. You can't just connect the car to the battery as it will go flat and destroy the battery, hence it has to be wired through the charger/BMS.
@rink853 жыл бұрын
which chip you are using in the video? can you please share some detail?
@akashdeeplakra35832 жыл бұрын
Lipo charging module 5volts
@tristanandfriendstv96 Жыл бұрын
What model chip did you use?
@MrPanksi3 жыл бұрын
how is this USB charging module called please?
@mati211p3 жыл бұрын
3 x AA White Eneloops will be working too.
@Maulana_rhodes5 ай бұрын
😮never thought of that
@fluggegecheimenn3 жыл бұрын
What's a problem to by rechargeable AA batteries?
@ARMTechHomemade3 жыл бұрын
Rechargeable AA batteries is 1.2v.
@jyotirani82323 жыл бұрын
Wow, nice idea.
@kirsehirpilbataryayenileme2 жыл бұрын
Ben 2 tane lion koydum paralel olarak güzel oldu
@thattoyvehicleguy90003 жыл бұрын
I've done similar but I just connected a USB cable to the battery wires and connected a power bank to that
@andre_pikes2 жыл бұрын
but how do you know battery is not overchaged?
@elementoliener24933 жыл бұрын
What module did u use for the battery
@petrmk42363 жыл бұрын
TP 4056
@addythakur7454 жыл бұрын
Good work my friend
@LordAnubis0909 Жыл бұрын
i'm adding this to all my kids toys. usualy i'm using old phone battery or 18650. it depends on free space in toy
@dialystatus1728Ай бұрын
Please the video is fake it didn't work because it needs 3 aa battery means. It needs 1.5*3=4.5 volts but battery output is 3.6 volts so it didn't work try to put more batteries and add resistor if need for remaining high voltage
@Xbell-The-Road-Rippers-Expert3 жыл бұрын
*This is absolutely amazing, I'll have to give this a try soon*
@GF-mf7ml10 ай бұрын
All you need is 14500 battery with charger and 2 AA dummy battery. They are very cheap and no need modify.
@Himanshublog3 жыл бұрын
ব্যাটারির সঙ্গে তার জোড়া মেশিনটা তৈরি করা দেখাও।
@gurnardherded3539 Жыл бұрын
WARNING: DO NOT SOLDER DIRECTLY TO A BATTERY LIKE HE DOES, this could lead to a fire do to overheating and rupturing the battery, you can watch linus tech tips video on making a power bank to see the proper way to solder a battery
@HastyRhombus760 Жыл бұрын
I have soldered directly to batteries literally 100s of times over the last 20 years without any issues. You just need to use common sense and not blast the thing with extended heat. Why do you think they make pre tinned battery strips (AKA solder tabbing) for connecting them when building a pack?
@hemshi7694 жыл бұрын
I think you are burning the circuit of RC because 18650 have higher amps it won't last long .