You brought back your own voice! Very nice. Also really appreciate the recent work in repairing the console. You're doing the community a big favor
@sthetixofficial9 ай бұрын
My pleasure!
@KuraV129 ай бұрын
@@sthetixofficial i just bought myself the mechanic xw5 solder wire as low melt solder. Is it good?
@sthetixofficial8 ай бұрын
it is good . make sure you add some flux to use it
@hawkfeather68029 ай бұрын
Nice to hear your voice again! And nice to see a very clean repair!
@sthetixofficial8 ай бұрын
thank you
@MrCANER069 ай бұрын
Job done like a pro !
@JirkaBalhar9 ай бұрын
For HDMI replacement on PlayStation, I use a solder sucker from Ali to suck out the solder in those anchor points while the board is still hot after removing the port. Try it, if it works on switch as well, it should be much less hassle than to try to remove it using the desoldering wire
@sthetixofficial9 ай бұрын
Thx for the info.
@MrZornick9 ай бұрын
Nice job, but is the low melt solder strong enough to hold the usb connector? Will it not break after time?
@sthetixofficial9 ай бұрын
it is fine. it is a lead free solder wire too. remember, the usb port is strengthen by two chassis screws too.
@hyperteknoman66029 ай бұрын
Your voice is changing, I hear it thicker, that means that when you started, you started young.
@sthetixofficial9 ай бұрын
😊
@snoopysnoopy74179 ай бұрын
clean job realy always the best bro thx
@sthetixofficial9 ай бұрын
Appreciate it!
@troyforce19 ай бұрын
Now this is a rough repair, even for a seasoned technician, because that second row underneath the port cannot be checked or touched up.
@JamsGrove5 ай бұрын
Great video mate! Have you got your hot air station set to 225c or are you measureing the heat on the board and use a higher temp for the hot air?
@sthetixofficial5 ай бұрын
the heat on the board. my setup is 400c for the hot air
@JamsGrove5 ай бұрын
@@sthetixofficial Nice, what do you use to measure the board temperature?
@sthetixofficial5 ай бұрын
@JamsGrove you can use a thermometer with K-type sensor.
@dannykusters68429 ай бұрын
Thanks for another great video! For this kind of repair I always hotswap the port. No need to remove the factory tin. Of course pre-tinning the port and only adding leaded solder the the mainboard pads. Saves time and have had literally zero returns.
@sthetixofficial8 ай бұрын
you are welcome
@maxmax-xx7nw2 ай бұрын
Nice video, however, I added this solder to joints, couple of times and still was not able to desolder it at 225°C(maybe too small nozzle), so I used 450° after 3 minutes of 225 and it went smoothly then😂 (but you are using sensor and i probably misunderstood)
@Skipperc3po9 ай бұрын
Thank you very much for this Video😀 is it safe to use low melt solder in the long term🤔
@sthetixofficial8 ай бұрын
it is safe. because it is not a "real" low melt solder, instead it is a solder with low melt temperature and usually phone technician use it
@fisrtrepair9 ай бұрын
Good job !!!
@sthetixofficial9 ай бұрын
thank you
@salasalsa-mb5gw9 ай бұрын
When you see professionals doing their job... 👍👍👍 .
@sthetixofficial8 ай бұрын
thank you
@salasalsa-mb5gw8 ай бұрын
@@sthetixofficial .... 👋 .
@leebardsley32489 ай бұрын
Perfect 🤩
@jamjam.1009 ай бұрын
Could you possibly place the USB-C on the top of the switch? This would make it more convenient for docks and be able to charge while on a table top, like the steam deck, rog ally, and legion go.
@sthetixofficial8 ай бұрын
yoi can use the official stand from nintendo like this www.nintendo.com/us/store/products/adjustable-charging-stand-for-nintendo-switch/
@donkeykongcountry21889 ай бұрын
Eres un crack... ❤
@sthetixofficial9 ай бұрын
thank you
@hamidmohammad50978 ай бұрын
Hello my friend, I had a problem with damage to five capacitors around the APU Switch Lite on the right side. This is due to a failure in soldering the hwfly chip cable. The question is: What is the voltage value of these capacitors? Are they all the same voltage value or do they differ? Please help. Thank you.
@sthetixofficial8 ай бұрын
Sorry I dont know about it. Try asking at the www.tronicsfixforum.com/
@writer60069 ай бұрын
two videos in 7 days??? who extended christmas?
@sthetixofficial9 ай бұрын
😁
@critiquetest25948 ай бұрын
Hey dude, pls can you refresh and redo the “how to setup from scratch” video ?