Restoration Gearbox Giant old | Reuse antique gearboxes | Rusty speed recovery system

Restoration Gearbox Giant old | Reuse antique gearboxes | Rusty speed recovery system
Restoration of old furniture. I love recovery. Repairing old and broken furniture is interesting
Thank you for watching my video. Have a nice day
All details about my channel:kzbin.info/door/vXV...

[@nixx1239]

Let's make a list of everything he did wrong: - Poured old oil back in at the end - Reinstalled old bearings (new bearings don't come wrapped in stretch foil) - Hammering those bearings on shafts could be acceptable if he made sure that piece of wood didn't contact outter sleeve (which he did not) - Hammering centering pins AFTER bolts were tightened (you are supposed to install centering pin first than tighten the bolts) - That lock nut which holds the flange is supposed to be installed with lock washer to prevent it from loosening - No assembly lube used, pretty bad for running in - All surfaces which need to seal (bearing caps, flanges etc.) should be stoned to remove any high spots or burrs - At 20:07 two more errors can be observed, first that shaft seal is in horrible condition and needs to be replaced. Second you painted the surface on the flange on which the shaft seal lip runs on. It will either not seal at all or the lip (or whats left of it) will wear out extremely fast - 2 of the 4 mounting bolt holes are broken and should have been repaired by brazing or welding on some material and machining afterwards I don't understand why you make these videos when you clearly don't understand what you are doing. Just my two cents. P.S. Sorry for bad english, not my primary language :)

[@someoneelse7629]

Yeah, someone said on another video "It's like watching a kid repaint a broken bicycle light" There is another channel that "restores" engines by scraping off the muck and repainting them. Sure they take them apart a bit, for no reason, but they don't replace anything.

[@oldschool1993]

Wash the old bearings out and wrap them in shrink wrap and pretend they are new- assemble them all bone dry. Use old seals and have them riding on painted seal surfaces.

[@restorationmetaltools4555]

thank you

[@youraveragejoe7644]

More like a paint job than a restoration

[@dennisbrantley6925]

Lets not forget that missing key on one of the pulleys and just put the old oil back in at less than the right amount for a gear box. just forget about replacing seals. Painted oil seal surfaces. Wrap old bearings in plastic wrap and pretend they are new and place in Dry. My goodness. I hope no one watches this and thinks this is anywhere close to being correct.

[@ussdiscovery6912]

How about those two rusty boots on the top cover? I mean REALLY? Couldn't even have cleaned them up, at least so they would look the part.

[@Simmons2358]

OK job - just a few issues. 1. Grease: I would use assembly grease when putting the thing back together. 2. Gaskets: Seems like there were some metal to metal points - I would replace gaskets with something and not depend on a metal to metal seal; 3. New Bolts ? - Those first four bolts you removed holding the base to something look like new bolts someone just put dirt on. 4. Hitting Painted surfaces - It would seem a bit better solution to place a wood piece against the painted surfaces and hit the wood piece instead of banging a newly painted surface directly. 5. Bearing Installation - I do not believe I would hammer on bearings like that - need a better process for installing race bearings. 6. I think I would use chemicals (perhaps simply vinegar) to remove the rust or as much rust as possible and then a wire brush or something similar.

[@restorationmetaltools4555]

thank you

[@draper5058]

Over all just need patience

[@restorationmetaltools4555]

@@draper5058 thank you

[@user-pt9gy9sw6n]

Механик недоучка,покрасил старые сальники,не поменял и не смазал подшипники,в трех-пяти литровый картер залил пол-литра масла и тд и тп.А забивать подшипник ножкой от табурета- шедеврально😂👍.

[@walterengler5709]

when you opened the thing up and it looked so damn good inside I knew this was going to be a great item to restore. Sure the outside was a mess but the core was well worth saving.

[@restorationmetaltools4555]

thank you

[@johnpearson9074]

0000

[@heli-man-]

You should have just pressure washed it and used a mop to paint it at least you could have saved a few hours and got the same result

[@restorationmetaltools4555]

thank you

[@DudeGuy-zt9eg]

Ahaha 😂

[@chrispbacon3042]

Love it!

[@Dethrider6]

This is painful to watch. This gearbox isn't gonna work for long.

[@restorationmetaltools4555]

thank you

[@haydengreensmith6894]

Zacry Carmichael agreed, not even a drop of oil or assembly lube. Or a bearing press.

[@nickcsuki8123]

In SE Asia it will...

[@deathcube2006]

didnt even change the metal clutches inside

[@rishabhsharma-sg3rq]

He added oil in gearbox but that oil was black ,like used oil. So it will not long run.

[@davemount2607]

It’s great not having to listen to music thank you

[@hansh3011]

Very handy to do everything on your heels

[@restorationmetaltools4555]

thank you have a nice day

[@daviscalderon5730]

6

[@user-eq5gl5ve3f]

ПЛОХАЯ реставрация. Сальник старый оставили. Мастер рукожоп

[@restorationmetaltools4555]

thank you have a nice day

[@restorationmetaltools4555]

@михаил журавлев thank you

[@user-eq5gl5ve3f]

@михаил журавлев Да и по краске молотком стучат, болты без шайб... Чисто для видосика...

[@Master_ot_god]

Почему он подшипники не смазал? Ведь заводская смазка для транспортировки и хранения но никак не эксплуатации!

[@rogerraven6976]

Such amazing video I could watch this over and over again. A great many love to you and your high guality content.

[@restorationmetaltools4555]

thank you

[@brucejones4538]

Don't they still make lubricant, this puppy is dryer than an Arabs jockstrap.

[@restorationmetaltools4555]

thank you

[@daengboim9186]

Can that bolt be opened using "impact wrench"? use that tool once in a while ..

[@restorationmetaltools4555]

thank you

[@user-sl8fd5gv1y]

это надо же додуматься шпатлевать чугун))

[@restorationmetaltools4555]

thank you

[@arapbaiumarbekov3589]

Че нельзя шпатлёвки

[@holymoly6829]

“Thinks” 🤭 Oil might piss out of this renovation 🤷‍♂️🤷‍♂️🥴🥴

[@restorationmetaltools4555]

thank you have a nice day

[@birabira3382]

Pra mim era sucata kkkk Ótimo trabalho Ótimo vídeo Um grande abraço pra vc e sua família

[@dehCremus]

Use grease in the bearings.

[@restorationmetaltools4555]

thank you

[@valpogi3791]

Its a pain in my eyes.. paint over rust.. and more.. :(

[@restorationmetaltools4555]

thank you

[@otktww]

技術力に乾杯🍻🥂

[@pdemarle]

Dude buy an arbor press it pains me to see you hammer in bearings like that

[@restorationmetaltools4555]

thank you

[@AlexeyBadalandabad]

Так себе восстановление! Мог бы не разбирать а так сверху покрасить))))

[@restorationmetaltools4555]

thank you have a nice day

[@rogerraven6976]

Excellent content! This video is a true asset to KZbin. Keep it up I known there are more gems hidden in your vincinty. 😻

[@restorationmetaltools4555]

thank you

[@rogerraven6976]

@TheJR1948 du kan ju försöka svara på mitt språk så ska jag säga hur bra det gick HAHAHA

[@taengakhiangte3921]

I like ur shoes..Legend

[@restorationmetaltools4555]

thank you

[@emmanuelhernandezdiaz4531]

Muy bien grande entre los grandes

[@restorationmetaltools4555]

thank you

[@leonardogabriel8255]

Muito bommm!!!! Mas merecia um óleo novo né kkkkkkk Leonardo São Paulo Brasil

[@sunosunone1237]

,

[@neillpotts6019]

No grease on the bearings or gears when reassembling and then you put half a cup of black used oil in at the end !?! It would probably have lasted longer if you had not 'restored ' it.

[@restorationmetaltools4555]

thank you

[@1959Berre]

A rubber spatula to apply the polyester filler works much easier than a metal putty knife.

[@paulorth2251]

Nicely done, sir. Interesting exterior condition, underwater find?

[@restorationmetaltools4555]

thank you have a nice day

[@gonzalocyftxtmogrijalva5855]

@@restorationmetaltools4555 cx

[@OneBillionView456]

i love this video

[@SuperSolenoide]

Boa noite não trocou os rolamentos e nem os retentores?

[@spyridon1971]

Super work! Thank you for sharing!

[@restorationmetaltools4555]

thank you

[@bigbattenberg]

Oh my - a total hack job if I ever saw one. Very painful.

[@restorationmetaltools4555]

thank you

[@fordfan3179]

I know you're just making due with what you have but there were a couple things that you can do in the future to make things work better. #1 dowel pins go in before the bolts. #2 you should have cleaned the seal surface on the output flange. It was painted! The paint will wipe out the seal (that should have been replaced also) #3 I would have thoroughly oiled all the internal parts during assembly. I mean drenched the stuff. Keep going!

[@restorationmetaltools4555]

thank you

[@DudeGuy-zt9eg]

1 there’s this thing called grease 2 with the seals don’t paint the surfaces 3 use NEW oil and use a lot more than the shot glass thst u put in 4 hammering bearings like that will ruin them (the “new” ones you put in) and the filler job thst you put on was poor

[@restorationmetaltools4555]

thank you

[@franciscosalamanca8174]

🇨🇴👍🏻

[@131dyana]

That will heat up and with no grease or oil on the bearings it will cease up.

[@restorationmetaltools4555]

thank you

[@studentmai]

А зачем шпатлевать корпус? Верхняя крышка не родная

[@keithspencersr.6806]

Oil may have been used to make assembly easier

[@johnzeller1338]

Where do you guys find this stuff. That's one great rebuild. Greatly enjoyed it from start to finish. 👍

[@alvaroaraujo5162]

Este cara e catedraco

[@curtislowe4577]

What machine or process was it used with? What are two gear ratios? Which ratio gears had the greatest wear? Any idea on the maximum input rpm or rated kw/hp? What was shaft stub opposite the clutch lever for? Is the hole above the clutch lever shaft just a vent or breather?

[@Multantechinfo]

Kosis to ache ki apny apna camra hiil bohat raha tha

[@racoman346]

Buenas , hasta cuanto hp soporta la caja inversora , gracias

[@StephenGoggin]

22:51 Where's the rod key?

[@restorationmetaltools4555]

thank you

[@user-do6qr9rm3l]

когда он начал вал выбивать по центровочному отверстию, я это выключил

[@restorationmetaltools4555]

thank you

[@nickcsuki8123]

Does anyone know where to get that seal in the exact color of your paint? That's amazing!

[@restorationmetaltools4555]

thank you

[@olgrizz_____5373]

Maybe a car paint company. A supplier to body shops?🖕

[@vikinglogan9715]

Everyone of these KZbin restoration Yahoos need to get an Arbor Press. The amount of bearings and shafts that get beat on would be unacceptable by any professional work place.

[@tilly6973]

Where's the grease???🥴

[@restorationmetaltools4555]

thank you

[@edfariah6250]

A tampa do óleo não queria muito negócio não...kkk

[@alvaroaraujo5162]

Este cara e catedratico.

[@buggyman4390]

I have the same gearbox in my boat ,where i can find the parts to repair? Please help ,,,

[@luigicristiani7709]

Was it reused after the restoration? How was it reused?

[@steveearnshaw1917]

As a boat anchor.

[@luigicristiani7709]

@@steveearnshaw1917 In the sense that you repaired it, taking time and perhaps even money ... to throw it into the sea and anchor a boat there ??? !!!

[@user-tm4ye3bv8m]

зачем менять старый сальник,если его можно покрасить! Гениально! Я просто в ахуе!

[@restorationmetaltools4555]

thank you

[@Anar6via]

Didn't replace the oil seal at 20:19. so it will let oil through and, in general, did not put any gaskets apart from between 2 blocks + the oil seals had to be changed

[@pritamshah554]

In my opinion, if you don't know precisely what you are restoring, what are technical specifications of it, what is function of it, what is function of all parts, what are the checks you need to carry out to determine if the part/parts meets the quality parameters or not, what is scientific / proper technical methed to repair/restore the part, what proper tools would need for restoration, what safety measures would need to take during restoration, what performance parameters such assembly needs to meet after restoration...then better get yourself aware of it before starting any repairs / restoration activity and then ensure that you follows/meets such scientific / technical practices and provides performance results as per product specification (especially when you are dealing with major assemblies like gear box or so). This will bring quality in your job as well as boost up your confidence and knowledge. Wishing you all the best.

[@handwork6270]

Tell me, how difficult is it to work with putty? Surface irregularities make it clear that this is not so easy 🤔🤯

[@nota-sx3oe]

Schönes Beispiel wie man es nicht machen sollte. Ich frage mich nur wofür die ganze Arbeit war?

[@marios.m.2728]

O rapaz usa máscara por vergonha deste serviço.

[@restorationmetaltools4555]

Use-o para evitar poeira

[@alexsyt462]

the fact that he burns himself. Sorry pal. Its happened to me too.

[@restorationmetaltools4555]

thank you

[@chrisatc627]

Is that wooden leg from a chair a oem tool? 😂

[@vinothansham]

Where you can use this item?

[@restorationmetaltools4555]

thank you

[@dwijaputra1804]

You are a profesional technichian. (may be a wrong word). What this machine function Mr?

[@DJBabb]

Watch enough of these (my mechanics, Rescue & Restore, etc.) and you learn what a good, clean restoration looks like. How things are cleaned, how they're restored, how they're reassembled. And while it's worth pointing out that that those guys seldom do things this big and that those guys have all sorts of tools and equipment for their projects, there's some techniques and eyes to detail they have that don't cost anything. This video however serves as a great example of bad restore. Bad color, bad sanding, bad restoration (too little oil and it appears used, no grease on the bearings, etc.). I'm not a mechanic or anything, but hammering gears into slanted gears just seems painfully, obviously wrong. So in that regard, I consider it a "good" video just to make me appreciate better the skill and attention to detail in others' projects.

[@10maruhachi12]

パテじゃなくて地金を削り磨いて欲しい。

[@restorationmetaltools4555]

thank you

[@BICHIMICTUL]

Уголок не приварили отколотый(((( за это скидку могут потребовать) Вы же потом все эти механизмы продаёте?

[@restorationmetaltools4555]

thank you

[@NguyenHung-fc6tm]

You are the great rebound

[@restorationmetaltools4555]

thank youb

[@otktww]

あと少し丁寧にすればGoodやな脳裏よぎった

[@abdsalam8196]

👍👍

[@1973chrisg8]

Just curious !!!! What does this go on or in ???? Lol

[@restorationmetaltools4555]

thank you

[@curtislowe4577]

Wondering that myself. A two speed reducer. I asked what the two ratios are but I'm not holding my breath about getting any answers.

[@pawpatrol2120]

Love video

[@olgrizz_____5373]

You ought to show your face at times. I certainly would enjoy seeing your face as you do these different channels.

[@restorationmetaltools4555]

thank you

[@Archiemonty]

And I thought I was rusty..

[@VictorPerez-pk6xc]

Pero si expliqueu que es eixa maquina ....ni si funciona

[@restorationmetaltools4555]

thank you

[@SailingYachtDreamcatcher]

Why do you clean and wrap the old bearings? Assemble without oil? this is a farce! Also, who taught you to hammer on the outer race of a bearing.....? What insanity to fit old damaged seals? How are you expecting the old seals to work on painted surfaces? Plus, you must first fit the locating dowels before you tighten the bolts, which each require at least a spring washer. What a waste of time reassembling like this. This is terrible workmanship!

[@restorationmetaltools4555]

thank you

[@flantrothehunter9935]

Hey dude he might not of known that. You don’t have to beat him down about it.

[@marinegearboxli6675]

good

[@Jessi-lb1pc]

Good video

[@dennisbuckner6957]

no new seals ouch

[@restorationmetaltools4555]

thank you

[@user-cx5cg7wg2o]

РУКАЖОП.....

[@Topman256]

топ!

[@adamkim411]

What is it !? What's the use !?

[@richiow68]

It’s a good effort my friend but you should read some of your comments left behind in order to learn about missed basic skills.. Some of us leave these comments in order for you to improve on what obviously you enjoy.. But please obtain some grease to start.. 19:48 a BIG mistake being made here👍

[@thefuture679]

Mauvaise Finissions de la peinture

[@technodaiver]

А что это за херабора?

[@restorationmetaltools4555]

Это коробка передач

[@user-de1cf6wr6v]

@@restorationmetaltools4555 от токарного что-ли?!

[@soundmaster1966]

Any use of oil or grease seems to be totally overrated🤣🤣🤣. So sorry for your time. And mine☹️

[@restorationmetaltools4555]

thank you have a nice day

[@131dyana]

He put no grease or oil on any of the bearings. That is not good.

[@restorationmetaltools4555]

thank you

[@steveearnshaw1917]

Title should be 'how to convert a marine gear box into a sand anchor'.

[@romankoval7422]

Не понимаю, нахрена шпаклевать, красить и потом херячить молотком? Зачистил бы ржавчину и сверху банку краски вылил. Не советую смотреть, 20 минут времени в жпу...

[@actiniumanarchy9237]

What did this gearbox come out of?

[@restorationmetaltools4555]

thank you

[@laskarkayuhitam5212]

Long Time...

[@restorationmetaltools4555]

thank you

[@SABORGASTRONOMICO]

Que es??

[@robertsnell2834]

Half assed restoration

[@marinobacic3543]

You will have oil leak because oil seal is old..

[@restorationmetaltools4555]

thank you

[@Harley_89]

Китаец что ли?

[@user-sl8fd5gv1y]

первый видос за всё время просмотра ютуба, где я поставил диз. НУ не считая путенских выступлений)

[@edgquin6715]

Funciono? No vi grasaaaaaaa

[@2gena68]

Нахрена шпатлевать, если ещё хуже сделал чем было. Подшипники я так понимаю старые, как и сальники. Это не реставрация, а так себе. По Русски это называется ху...ня.

[@arcturus5629]

nabijanie łożysk w zaprezentowany sposób to ich zniszczenie! to żadna renowacja tylko odmalowanie. łożyska powinny być wymienione i wciśnięte na prasie anie kawałkiem drewna nabite!

[@restorationmetaltools4555]

thank you have a nice day

[@romihofi8848]

Nawet uszczelniaczy nie wymienił.Tak jak mówisz rozebral wyczyścil pomalowal i poskladal. 😂

[@arschgeige7178]

Keine U-Scheiben, alte Lager und Simmeringe, einfach Pfusch!!!!!!!!!!!!

[@rebecagomez3915]

No me gustó como quedó, la pintura no la dejo secar y la dejo toda levantada y marcada, no me gusto el exceso de pasta que le dejó no lijo, en general no me gusta

[@arnoldpraesent174]

Hhmmm... I don’t see the Restauration to be honest. It’s disassembling with hammer, cleaning, painting over rust and filler, assembling with hammer bone dry... the gears doesn’t look very healthy... anyway, there is room for improvement I guess. Editing the clip and cut is good, like it!

[@restorationmetaltools4555]

thank you

[@ic835]

I hate when thses guys put filler on top of rust to make it look good. Butures. Sandblast is the proper way to restore. Looked ugly and nasty at the end

[@otktww]

あと少し丁寧にすればGoodやな脳裏やな