Restoration Hydraulic Jack | Restaurare cric hidraulic

[@j.rothchild173]

Good job! Awesome 80s jams, too!!!

[@DorelBorlea]

Thanks!

[@ferdinandcalixton1559]

Hm does it cost for the labor price please?

[@carmelpule6954]

In my opinion, only 5 minutes out of 25 minutes were used to cover the clever parts of the Hydraulic unit while the high-pressure cylinder was not taken off/dismantled to show the final ball valve in it. In fact, none of the ball valves were shown. most of the time the video showed the use of a wire brush removing the paint and a few coats of undercoat and topcoat were shown including the assembly which is not really very difficult.. The last one I overhauled had four-ball valves used as follows. a. One ball bearing valve for the return release path. b. Two ball-bearing working in unison to produce the pump9ing action.' c. One ball bearing with spring loading to act as a high-pressure relief valve. This hydraulic jack is interesting and careful tightening is required as when one tightens the top nut to push down the reservoir outer cylinder, the central high-pressure cylinder is lifted up, and if it is not tightened extremely tight it could lift a little and leak at the lower copper seal which also holds in place the final ballbearing high-pressure valve.

[@DorelBorlea]

My intention was to fix this jack and make it look better. I didn't want to disassemble all the valves because there were no problems with them. If I had disassembled all the parts, the video would have been more interesting, but making such a detailed video takes a long time and I tried to make it as short as possible. Thanks for the comment. I will take into account your opinion for the next videos.

[@miliady]

@@DorelBorlea where are you from? how can i contact you as i have a floor jack like this that i would like to repair as it is leaking everywhere

[@PinBall3]

Good Restoration On The Jack I Have The Same Model In The Green Color I Got New In 1993 From Sears Still On Its Original Seals And Lifts Like A Champ To This Day

[@bonifaciojose674]

What is the model number please?..

[@PinBall3]

@@bonifaciojose674 Sears 328 Series Find info on Hcrcnow dot com www.hcrcnow.com/uploads/drawings/sears328seriesjacks.pdf

[@pcofranc]

@@bonifaciojose674 I have a Sears Floor Jack mfg 08-1990 Model # 214.50112 Two common model groups are #325 and #214 but #325 seems to be way more popular for rebuild kits. I think I will go to a local hydraulic seal shop and get a new piston o-ring and one for the round vertical pump shaft as nothing else leaks. I also have a harbor freight aluminum Jack US General brand Item # 91039 1-1/2 ton 3,000 lbs that purchased new in 2003 and the piston leaks a bit and needs a new o-ring.

[@jamesross117]

Very good! This is a complete tear down and reassembly of a floor Jack. Other videos are just periodic maintenance. Thanks for doing this.

[@tovarvictor8467]

Can you tell me what measures are the o ring than those for the cylinder

[@wmoy8507]

Great job. It looks like the same jack I bought about 35 years ago and was working until recently. It probably needs new fluid. My concern is the o rings you use. I think the material is buna which I believe is not compatible with hydraulic fluid. Doing some research your should use viton o rings which is long lasting exposed to hydraulic fluid. Do not know how long your replacement seals will last.

[@mariosciore3527]

great job where can you get the O rings for it to rebuild it

[@hamrhal]

In a plastic tub, with a whole bunch of others. sort through and pick one. @ 5:00

[@SharpObserver1A]

En amazon, por approximadamente 35 Dolares un juego de empaques, son carisimos y solo usas la mitad de los empaques.

[@spelanalys]

I have an old jack, same model as yours. It works, however when I want to release the pressure and lower whatever I'm working on (usually my boat on a trailer) - it always comes down with a boom. What can I do so pressure is released little by little and the boat is lowered smoothly? I try to turn the screw/handle as slowly as possible of course, but it doesn't help.

[@DorelBorlea]

I think the trailer and the boat are too heavy for this jack and because of this the jack goes down very fast.

[@spelanalys]

@@DorelBorlea Hm, you think? The boat is only 900 kg. I don't remember how much the jack can take but is seems like a beefy piece of equipment. It's really heavy.

[@DorelBorlea]

The maximum load is 2 tons. Try to lift a car and you will see that it will go down more slowly. You have to untie that handle very slowly and wait for it to come down.

[@jorgiporgi1105]

May you please tell me what is the name and model of the jack? And the ton rating? Just asking I’m gathering it’s the swivel cog at 4:45 in your vid would you put Teflon tape around the bolt when reinstalled? Thank you. I’m all the way in Australia 🇦🇺

[@DorelBorlea]

The jack lifts a maximum of 2 tons, I don't know what this jack is called. Teflon tape is not necessary.

[@dim4051]

Здравствуйте, подскажите пожалуйста как стоят шарики и пружинки в каналах. Начал свой разбирать и мне кажется что-то потерял

[@DorelBorlea]

Существует несколько моделей домкратов. У одних система закрытия с шариком и пружиной, у других - своеобразный поршень с цилиндрической прокладкой, у третьих - конический поршень с пружиной.

[@robpeters5204]

I have one exactly like this one. I bought mine in the early 90's works great still.

[@DorelBorlea]

It's a very good jack. I am very pleased with it.

[@thomasbardwell4151]

I also have the same jack MVP speedy lift 3 ton BUT I CANT FIND THE KIT ..DO YOU HAPPEN TO KNOW THIS KIT NUMBER ON THE JACK ON THIS VIDEO?

[@acatsaid5411]

@@thomasbardwell4151 did you ever find out?

[@PinBall3]

@@acatsaid5411 Try This Here ? > www.hcrcnow.com/shop/seal-kits/mvp-by-shinn-fu-america Good Luck

[@bonifaciojose674]

Mine too..need the parts numbers for the rings..

[@MihaSun]

Bravo frăție

[@eduardonavaq5383]

Donde consigues los oring???

[@SharpObserver1A]

En amazon, por approximadamente 35 Dolares un juego de empaques, son carisimos y solo usas la mitad de los empaques.

[@大谷直行-k8o]

素晴らしいです!僕も今、これと同じ作業をしています！シリンダーの六角ナットがなかなか外す事ができず悩んでいたところでした!でかい万力とパイプレンチがあれば外れる事が分かりました。ありがとうございました！

[@DorelBorlea]

あなたが私のビデオを気に入ってくれてうれしいです。 なんとかそれを復元して、私と同じように結果を楽しんでください。 成功！

[@大谷直行-k8o]

ありがとうございます本当に助かりました!

[@wilberrondinelcordova4438]

Donde queda el taller de mantenimiento de Gata hidráulica

[@DorelBorlea]

Compré este conector defectuoso y lo reacondicioné. Cambié las juntas defectuosas. El gato funciona muy bien ahora.

[@boblamb8421]

Great video. I have a Larin 6000 pound floor jack. The company says they don't have a rebuild kit for it anymore. Where can I buy a kit for my jack? It actually looks like a Craftsman jack. I've looked at the insides of many old floor jacks I could have repaired had there been seals for it. I find it hard to believe the piston rod seal is different in all jacks. My guess is it's the same one in every kit. Any help can save a very usable older jack.

[@hishamchohan494]

O-rings and steal balls..etc.,and atf or hydraulic fluid

[@hishamchohan494]

Hi, please go to a local hydraulic repair shop and they can help you,... You can find main piston hydraulic seal blue color or they can custom make one for you if they can .. O

[@frankinga3120]

Would have been better if you had replaced all the seals, and greased all the friction areas; also did you run out of orange paint?

[@DorelBorlea]

I had to wait another day for the paint to dry. I was in a little hurry. ;)

[@classics289]

How come you didn't paint the rest of it? It looks pretty weird with primer showing.

[@DorelBorlea]

I thought it looked better this way.

[@theresahoffman8408]

You didn't replace any o rings on the valving? Just the one on the piston?

[@DorelBorlea]

I only replaced the main piston o rings. Only those had problems.

[@AntonioMartinez-ww2hm]

Donde consigo los empaques

[@maximoaguilar8854]

Disculpa donde puedo conseguir el quit de reparación por tu atención gracias

[@abdongregorioruizmaldonado8333]

Gracias por compartir Dios te bendiga .pregunta donde condiges los empaque o ligas

[@DorelBorlea]

Dios te bendiga. Tengo un tractor y le cambié muchas juntas. Entre esos sellos encontré algunos que se ajustan a este gato.

[@chanthysok2548]

@@DorelBorlea.

[@tomlakeandriver7670]

Hello and thank you for sharing, however I have the same jack that I am redoing that I have for over 20 years. In the part of the rectangular block or this troube the farmeture piston there are small balls in each compartment can you tell me where it really reopens because by wanting to empty it the whole is to fall.

[@DorelBorlea]

There are steel balls in the piston compartment and in the overpressure valve compartment. But I didn't understand what you meant in the last part of the comment.

[@Mr572u]

You left the main frames in primer? After all that prep work? Man......

[@Daltisk97]

Greetings! I have a question, how do you eliminate the oil leak from the pumping rod?

[@DorelBorlea]

Hello. The seals on the pump rod must be replaced.

[@Qspecialman]

I have the same jack, any idea where I can buy a kit please to rebuild the seals plus the conical spring they got away?

[@negakevin8336]

Nomas tu sabes lo que estas haciendo se supone que debes de explicar paso a paso no como lo estas pasando bato en csmara rapida que bato tan pen

[@DorelBorlea]

No tenía la intención de hacer un tutorial sobre cómo reparar este gato hidráulico. Acabo de hacer una restauración. Alguien instaló algunas juntas que no eran parte de ese gato. Y debido a esas juntas, todo el petróleo fluyó.

[@JoseDiaz-tf4su]

En qué tienda compra los empaques

[@antongorrio]

Hi ! In which hole goes the two steel pellets and the string?

[@kevinlamarr1424]

I have an old jack that fits under the bumper like the air jack in a truck repair shop. I bought it to restore it. I’m hoping that place has a kit for it. Thanks

[@DorelBorlea]

I also like to repair and restore things. It would be interesting to make a video with the jack restored by you.

[@kevinlamarr1424]

Dorel Borlea Thanks for the interest! I’m a truck driver and I’m just getting started making videos. I have a jack just like that one that I’m going to restore. I also have a 1984 Winnebago chieftain 33 that I’m working on. Not an expert by any means but I wanna do it with my little 5-12 year old nieces and nephews.

[@DorelBorlea]

It's a nice way to spend your time. The satisfaction is very high when you manage to repair something. Especially if you have some children around. Good luck.

[@kevinlamarr1424]

Dorel Borlea Thanks 🙏 I’ll let you know when I get started and post a video I’m on the road full time so I move kind of slow

[@DerMoelly]

Thanks for your great video! With the video you convinced me to buy the same *"Hein Werner O'Boy"* , which, however, has lost oil. Your video showed how easy it is to set up the jack! Greetings from Germany!

[@robertomena2111]

Donde puedo conseguir las refacciones de los gatos?

[@DorelBorlea]

No lo sé.

[@hishamchohan494]

Hi,you did a nice job in restoration but the main thing is hydraulic repair... You did not remove the fluid tank cylinder from the mian. And the oil plug must be up side ...see other videos of china jack

[@edwinsoto204]

de cuatas tonelada es y como consigo el kit

[@simonilett998]

Looks good👍 But how do you fill the oil now? You assembled the cylinder with the oil filler plug at the bottom??....LOL

[@DorelBorlea]

Thanks! I will turn the hydraulic car jack upside down and add oil through the filler plug. In my opinion the oil filler plug must be placed at the bottom.

[@simonilett998]

Ok sure, that should'nt make much difference. Every other trolley jack I've seen (including your's - before you pulled it apart) has the plug mostly upwards, so it can be filled to the correct level in it's operating position??.. and i guess it would save the oil plug getting knocked out while rolling on some uneven surface etc...nice oil leak everywhere....lol

[@DorelBorlea]

At this jack, to feed oil through the top you have to disassemble the upper arm. If you think there is a risk that the oil plug will pop out accidentally then you mount it on top. Do what you think is best for you.

[@Mark11n23]

Hey, I got a problem, and it won't turn. It has rust in it. I did tried with WD-40 but it won't budge. What would you suggest for me to do?

[@DorelBorlea]

Disassemble it and clean the rust.

[@Mark11n23]

@@DorelBorlea YES! I got it and it works .......... thank you... WHOO!

[@craigstricklin7297]

I have this exact Jack I would like to rebuild a cylinder don't have any clue what size it is or where to get the parts can you help?

[@DorelBorlea]

I can't help you either. I don't know what the dimensions of the cylinder are.

[@thaddeauscaldwell7101]

Thank you for the great video. I bought this same jack a couple days ago from a friend for $10. The jack will jack up but won't go down when I try to turn the handle. The handle won't turn. I took off the lower sprocket but the bolt that let's down the jack won't turn. You did the repair @4:35. Do you know how I can fix this issue ? Any information is greatly appreciated. Thank you.

[@DorelBorlea]

it's probably stuck, you should disassemble that part and remove the bolt and grease it

[@armandocallizaya1540]

Escribo de Bolivia, como puedo adquirir retenes para gato hidráulico y donde ? Por favor respuesta, y gracias.

[@DorelBorlea]

Hola. Tienes que buscar en Google sellos hidráulicos. Vea qué juntas están defectuosas en el gato, mida y ordene desde allí.

[@chelseylover1]

Whats the part number of seal replacement

[@kadekad686]

Bonjour j ai exactement le même cric ou pourrais je trouver les pièces d Etacher merci

[@DorelBorlea]

Pour réparer un tel cric. Vous n'avez pas besoin de changer tous les joints. Seulement ceux qui ont des problèmes. Achetez une boîte avec des joints toriques en caoutchouc et remplacez ceux cassés. yato.com/products/11/YT-06877

[@kadekad686]

@@DorelBorlea merci mais j ai commandé des joints j attend de les recevoir s

[@peruchoa2]

Greeaaaat man.

[@bonifaciojose674]

What is the part number kit for this jack? Please..

[@mohabatkhanmalak1161]

What make jack is this. It looks like one of the top quality ones that you cannot get nowadays.

[@DorelBorlea]

I don't know where this jack was made, but it's a pretty good one.

[@handymanjim5488]

Sears craftsman 328 series from the 70s

[@DorelBorlea]

@@handymanjim5488 thanks!

[@ЛюдмилаПинегина-о1б]

Potevi verniciare anche il lato interno, invece di lasciarlo grigio.. .. complimenti bel lavoro

[@DorelBorlea]

Ho dovuto aspettare un altro giorno perché la vernice si asciugasse. Avevo un po' di fretta. Anche a me sembrava buono.

[@everardoherrera2203]

need help my jack got stuck up position... the gear or sprocket shape don't move

[@DorelBorlea]

In order to move the gear, you must raise the lever in an upright position. Maybe a little petroleum jelly helps.

[@reginaldopaulasilvasilva1953]

Boa noite! Tenho um macaco desse aí e fui meche nele porque não estava levantando direito aí fui tirar esses dois parafuzos que tem em cima dele ai saiu mas molas e uma esfera grande u uma pequena e não sei a posição delas vc pode me ajudar?

[@michaelb8249]

Any sizes for the replacement o-rings? I'm particularly interested in the nylon washer inside the pump shaft that sits below an o-ring (size 208).

[@hishamchohan494]

Well it must be a 45°degree cut nylon ring

[@adeltaibi4003]

Good job 👌👌👍👌👍👌

[@DorelBorlea]

thanks!

[@backtonatureitis]

Buna ziua domnul @Dorel Borlea Am un cric foarte asemanator cu cel din videoclipul dvs pe care vreau sa-l restaurez. Imi puteti spune va rog de unde ati cumparat garniturile pentru el si cate tone are? Sanatate

[@DorelBorlea]

Salut. Cricul ridica 2 tone. Garnituri se gasesc la magazinele cu piese pentru tractor.

[@backtonatureitis]

@@DorelBorlea Cat ulei hidraulic intra intr-un cric de 2-3 tone? P.S am gasit sa cumpar garnituri la dimensiune de pe internet. Te salut!

[@DorelBorlea]

@@backtonatureitis in jur de 200 grame.

[@921aa]

The pump and ram are the the o-rings hat wear out and cause the jack to fail. It doesn't look like you replaced either.

[@DorelBorlea]

I just replaced the gaskets are they were broken. A valve was clogged with a piece of gasket and that is why the jack went down.

[@kadekad686]

Hello could you tell me what is the brand of the jack I have exactly the same I count the renovated thank you

[@DorelBorlea]

SEARS Floor Jack

[@ferforge7664]

J'ai le même modèle je trouve pas les joints Spy hydrologique 😭

[@ouahchiamor7627]

Hello, specification of oil please

[@hapciu3d123]

salutare.. cu tot respectul unde pot gasi garnituri sau oringuri pt un cric de 2 tone ?

[@DorelBorlea]

Salut. Depinde ce fel de garnituri trebuie la cricul respectiv. Poti sa gasesti la magazinele cu piese auto sau online. Masori dimensiunile garniturilor si comanzi online.

[@hapciu3d123]

@@DorelBorlea multumesc frumos !!!!

[@VinnieVega76]

Fantastic restoration! Question though. Do I have to go through that entire process just to get my jack to work, or can I just bleed it? One hell of a great job you did there I have an old one too that does exactly that, but do I have to remove everything like you just did? You're probably going to tell me that the O-ring is shot

[@DorelBorlea]

This jack had oil leaks. There were some leftovers from a broken gasket. To remove the cylinder you have to disassemble the side parts. Analyze carefully and see what the problem might be. In this video I did not show how I cleaned the blocked channels.

[@VinnieVega76]

Thanks

[@robertmoyer2311]

Ok so I made the mistake of taking the Allen head plug out. A steel ball fell out, put back in, but jack won't work. Am I missing something?

[@DorelBorlea]

Search for a sketch of the jack. Maybe a washer or a spring missing there.

[@notajp]

Check to see if a second ball might have fallen out too. Usually you will have a small ball bearing on the bottom with a larger ball on top. There may be a spring too. On my jack like this, there is a small ball at the bottom, a larger one above it, and a tapered spring on top under the plug. Narrow end of the spring down on the large ball. Not all jacks are the same tho. Those balls are check valves for the pump. One for in, one for out.

[@robertmoyer2311]

@@notajp thanks for the reply, that's exactly what happened. Found the little ball in the driveway. Jack working good again.

[@emmanuelbarnay1022]

Hello I bought the same hydraulic jack 2 tons in France 25 years ago. I don't know who the manufacturer is. I am looking to replace the wiper seal on the small control rod located on the left of the block. Can you tell me about the manufacturer? Translation by google Thank you

[@DorelBorlea]

328.1200 is the model of this hydraulic jack. Search on google about that number and you will find info

[@luiscasanova7003]

Love the music ...... uuuufffff!!!!

[@ignacioanaya3403]

very nice job

[@DorelBorlea]

Thanks

[@martillodelacruz6416]

ReIrimos excelente rieparat

[@edwinsoto3560]

De cuanta tonelada es y el número de id

[@santy1030]

very Good.

[@adamorossi4333]

Salve ti scrivo per la scava patate hai seguito un disegno oppure hai fatto di idea tua. Vorrei provare a costruirla grazie saluti

[@DorelBorlea]

Salve, non avevo uno schizzo per la costruzione della raccogli patate. Ho visto questa macchina e mi è piaciuto come funziona e ho deciso di costruirne una da solo. Per utilizzare una raccogli patate hai bisogno di un piccolo trattore o di un coltivatore.

[@kadekad686]

Bonjour pourriez-vous me dire quel est la marque du cric j ai exatement le même je compte le rénové merci

[@radughelase1644]

cum te pot gasi? Am un cric hidraulic la care as dori acelasi lucru.

[@DorelBorlea]

Salut. Am reconditionat cricul pentru mine. Nu am timp sa ma ocup de alte reconditionari. ;)

[@radughelase1644]

@@DorelBorlea îmi poți recomanda pe cineva care să lucreze ok? Lucrarea ta îmi place, am urmărit video cu interes

[@DorelBorlea]

@@radughelase1644 doar daca incerci sa il reconditionezi singur. Ca nu stiu daca se merita sa platesti pe cineva

[@gaspardujon7191]

WHERE CAN I GET O RING SEAL KIT FOR THIS JACK ?

[@DorelBorlea]

I dont know.

[@PinBall3]

www.hcrcnow.com/

[@markarmstrong3394]

At 4:44 what is that part called ? I have a Jet floor jack and that stripped and the gear just keeps turning. Thank you

[@bonifaciojose674]

What is the part number for this jack?

[@DorelBorlea]

I don't know

[@gustavomazcorro7421]

Mi gato no levanta es un gato patin de 2 toneladas, ya lo cargué de aceite y no levanta, si no levanta como lo purgó

[@DorelBorlea]

Antes de poner aceite, ¿recogerlo? ¿Dónde pusiste el aceite en el gato? ¿Cuál crees que sería el problema de no criar? ¿Qué trataste de hacerles?

[@gustavomazcorro7421]

@@DorelBorlea no te entiendo tu respuestas, si le cargué el aceite pues es en el depósito

[@gustavomazcorro7421]

@@DorelBorlea no te entiendo tu respuesta el aceite se lo puse en el depósito quitandole el tapón de plastico

[@DorelBorlea]

@@gustavomazcorro7421 Usa el traductor de Google. No entiendo español. Es muy difícil para mí explicarlo. Hay varios defectos posibles. La junta está rota, la válvula está obstruida. Mire un video y vea cuáles son los componentes del gato. Intenta comprender el principio de funcionamiento.

[@gustavomazcorro7421]

Pues claro que le quite el papon de plástico si no en donde le pondria el aceite

[@ประจักรศิลทีปะลา]

อยากรู้ราคาที่แน่ชัดครับ

[@DorelBorlea]

มันไม่ได้ขาย ฉันปรับสภาพแจ็คเพื่อตัวเอง

[@valmeronsales3283]

Very Very good beautiful

[@DorelBorlea]

Thanks ! I'm glad you liked this video

[@SeeMooreVids]

Nice. I’ve got and old jack, looks similar I’ve been wanting to rehab. Has leak. A Hein... O’Boy. Something like that. Thanks

[@ytuhcsna]

I have an O’Boy which I love. It needs a fluid fill and I can’t find the place to add fluid. No little rubber plug on the cylinder. What to do?

[@brandonfeils6883]

@@ytuhcsna look at the pdf on this site. www.hcrcnow.com/shop/seal-kits/product/1301

[@rickyhensley6236]

@@brandonfeils6883 were u get the parts n wat 2 ask 4

[@brandonfeils6883]

Ricky Hensley follow the link above

[@urbexd4479]

Cant get my one working

[@DorelBorlea]

It is necessary to disassemble and see what the problems are. Maybe a gasket is broken or the valves are clogged with dirt.

[@urbexd4479]

@@DorelBorlea do u have Instagram

[@ประจักรศิลทีปะลา]

ราคาเท่าไหร่ครับ

[@alanymc1468]

Lokasi mana bengkel nya

[@ferdinandcalixton1559]

Hm labor materials pag nag restore ng ganito?

[@ferdinandcalixton1559]

Hm does it cost? For restoration

[@sambou7811]

Good job

[@DorelBorlea]

Thanks !

[@rambeza]

А у меня при разборке выпал крошечный шарик и какая то подставочка под него.

[@ninoratakingofspam5828]

Gracias a su video no use la pulidora para sacar el

[@cesarvaldiviezo1790]

Cuando quite los opresores

[@braulioalvaradomadrueno4291]

esta excelente el tutorial solo que me parece muy rapido y no deja apreciar paso a paso la reparacion , me gustaria que no incluyera lo de la pintura mejor darle mas dedicacion a lo que es la reparacion

[@jorgemelendez9546]

To much work but well done worth it

[@DorelBorlea]

Thank you!

[@kasemfalahkasemfalah6749]

Thanks

[@lionden4]

This guy have a of patience…. 😊

[@victorperalta624]

Todo muy bien Pero le pusiste el tapón del aceite por abajo y va por arriba

[@marianopacheco8888]

because it could be that my cat like the one in the video doesn't go up?

[@flaviudiy7140]

Ce model e makita ?? Ii pe impact

[@DorelBorlea]

Da este cu impact. Aici este un link spre un video despre surubelnita cu impact makita kzbin.info/www/bejne/n5_Hk4eZi7ODqK8

[@kadekad686]

Bonjour pourriez-vous me dire quel est la marque du cric j ai exatement le même je compte le rénové merci

[@danielmartinezperez4884]

Q vídeo tan inofisioso ....

[@nihalakula3761]

I want to restore my Jack

[@GLADIADOR00777]

Todo el video pasa tan rápido que no ofrece mucho mal video

[@DorelBorlea]

La duración original del video es de 2 horas. No creo que nadie vea un video tan largo.

[@m.anasalmasry4928]

Mantap

[@GlynRobinson]

Wish you’d do the one I have just like that one. Lol

[@DorelBorlea]

:)

[@al3xoradea]

Buna Poti sa imi zici si mie te rog ce tip de ulei ai folosit la umplere mai exact producatorul si ce specificatii are Multumesc anticipat PS: Un video foarte ok MESERIAS :D

[@DorelBorlea]

Am folosit ulei hidraulic. Pentru tractoare.

[@al3xoradea]

@@DorelBorlea ok mersi

[@yewinnaingyelay6994]

မြန်မာပြည်သား

[@АлександрЛитвиненко-ф7й]

Идиотский ролик мужик сразу чистит домкрат а потом его красит . И это всё? Гениально!!!

[@cesar.arambulacardenas6692]

Atte César Cárdenas de Guadalajara mex

[@MiguelSanchez-vr1vp]

agan vien sus videos

[@truthwillsetyoufree85]

The paint job is bad but otherwise good job.

[@cesarvaldiviezo1790]

A mi me salieron unas baño mas 2 chicas y una grande

[@joaquinchacoma4890]

No no enseñaste nada las válvulas quería ver pero as cambiado gomas nomás

[@DorelBorlea]

Abrí las válvulas y las revisé. No hubo problemas si a partir de eso no introduje esa parte en la filmación.

[@DorelBorlea]

Quizás este video te ayude : kzbin.info/www/bejne/nmnYamNves2hgrc