Reversing Polarity With Stop Switches

[@NicholasOliver-vo6jg]

Thank you so much. This circuit is exactly what I needed to power the headlight pods on my car restoration. It has saved me hours!

[@leonidaslazaridis7857]

finally a wiring diagram that I understand which I will use for honey extractor thx so much..can i change the magnetic switch to regular switches?? if i have to connect speed controller shall I connect after the battery or before the electric motor ??

[@mikmaster63]

@@leonidaslazaridis7857 yes, I think just about any switch that opens and closes with the correct power rating would work…

[@leonidaslazaridis7857]

@@mikmaster63 if i have to connect speed controller shall I connect after the battery or before the electric motor ??

[@mikmaster63]

@ kzbin.info/www/bejne/kH26nnZ-n7J0q7csi=R5vxxdXYfHlFc2Wt

[@mikmaster63]

@ kzbin.info/www/bejne/nYqwl6yZhZ5pn7csi=viWhCvUmnWRB2bp-

[@bearsstuff]

Thank you for this.

[@josefmarzano3914]

I like it. Thanks for share.

[@clydefuller4730]

It's been nice if you to put the numbers when you're explaining it or where it goes where I like 87 87a 86 85 and 30 if you to put the numbers somebody with a note how to wire it up

[@mikmaster63]

I’ll do that in the future. I didn’t even realize that because I’ve been using them for so long and I’ve never looked at the numbers. I always check them with a meter when I get a different brand or style…

[@madeingreatbritainchannel]

Great video. I am tying to make a roller that imprints bees wax foundation which is about 18 inches long it needs to turn forward and reverse and stop at end of the cycles. Start one cycle hit a reed switch turn the other cycle and stop back to the starting position. I can use micro swithes. I am thinking this would do that?

[@mikmaster63]

Thanks. I have other videos that might help. Here’s a link for one. kzbin.info/www/bejne/gIfPaq2CopiViqssi=oBpzYE05dcg5ejOF

[@mikmaster63]

Also you might check aztecwarrior69 he has some good ones too. You can find him in some of my comments

[@madeingreatbritainchannel]

Thanks I have watched this one, but I need it to stop after 2 cycles so I can reload the wax foundation and imprint it.@@mikmaster63

[@shyamlallal5469]

What type of switch ? is it puls switch ?

[@mikmaster63]

On/off switch. Press and it closes press again and it opens

[@shyamlallal5469]

@@mikmaster63 ok thank you

[@MrBarth43]

haga un circuito de 3 paradas y cuando llegue a la cuarta con el swiche vuelva a la posicion inicial..! gracias

[@mikmaster63]

@@MrBarth43 kzbin.info/www/bejne/n6HSaXiir7aCiLMsi=uJj1UQ2CApamQpqk

[@MrBarth43]

@@mikmaster63 gracias por la respuesta oportuna y elvideo..! queria uno de su autoria con los relay que los fabrica mas claro y sencillo..!

[@ketko24]

Hi, this is impressive, well done. Will this setup work same way, if instead of push button switch, just disconnect/connect power(using a timer for the main power supply)?

[@mikmaster63]

Ya if I’m understanding correctly I think it would work. There’s always a way to make it work…

[@ketko24]

@@mikmaster63 If it works, that will be great. I just wonder if is this red switch push button switch normally closed, like when it press is open, when release is closed(disconnect/connect in one step)? Or is act like normal switch? Thanks.

[@mikmaster63]

@@ketko24 when the red switch is pushed in it’s closed and when it’s released (out/up) it is open

[@ketko24]

@@mikmaster63 Thanks for explanation. Maybe I can replace this switch with timer(not sure how will work with 1min connection). Hope will have all components soon and try it out. Thanks for inspiration.

[@AztecWarrior69_69]

Yes it would but if you get a spdt timer. You can eliminate the switch and one relay. So one SPDT timer and two relays. Or two SPDT timers. And of course the limit switches.

[@scottkrieman8108]

I'm trying to wire up almost this same set up for an auto resetting slingshot target with a flash pot that makes a big poof of smoke. the only thing is I need the motor to immediately reverse when the top reed switch is reached and not just stop. I would like to hire a tutor that could teach me in person as we build my project. I have built a resetting target that resets with a pull solenoid but the new target is heavier and the stroke on solenoids is not long enough so I need to use a motor.

[@mikmaster63]

kzbin.info/www/bejne/gIfPaq2CopiViqssi=s9M8cszEr-zKJk7y If I’m understanding correctly, maybe this. Just remove speed controllers

[@scottkrieman8108]

Thank you very much for your response I'm still trying to figure it out. It's great that there people like you that take the time to help others😃@@mikmaster63

[@scottkrieman8108]

I just now noticed there are more than two wires coming off your motor and my motor only has two not sure if I can do this.@@mikmaster63

[@jimnelson7740]

I like it, but I need a circuit that will self-reverse at about .3 cycles/second. (1 cycle/ 3 seconds)

[@AztecWarrior69_69]

Why not just use a SPDT rocker/toggle/button switch?

[@mikmaster63]

Someone asked me how I would make this scenario work. I have videos on reversing polarity switches also…

[@AztecWarrior69_69]

@@mikmaster63 Oh someone asked you to create it so a single press/depress button to reverse polarity on the motor. OK Well in your other videos I have seen you put in the description that you were asked about it. You don't have any mention of being asked on this one. So I had to ask why. Still I would have just used a SPDT rocker/toggle/button switch. Less wiring. Less power consumption.

[@mikmaster63]

I started with RV related videos. One of them was a circuit to reverse polarity with relays. Then I started getting requests on how to do different types of circuits. I don’t watched other videos or Google it. I try and figure them out on my own. That’s the fun part for me. So they may not always be the best way to do something but they may give someone some ideas on how to do something. The next one I have coming out was a lot of fun to do…

[@IAn-bq9jw]

Any chance you have a diagram for changing the direction of the motor without having to restart it with the on/off button? So the object moved by the motor can travel each way in a automatic fashion

[@mikmaster63]

That’s going to take some thought. Maybe just removing the switch and when the magnets get to the reed switch it should go the other direction automatically. I don’t know if that would wear out the components prematurely. I’ll think on it and if I come up with something I’ll let you know.

[@mikmaster63]

Just uploaded a video hope it helps. kzbin.info/www/bejne/enupdoOVg6uYppo

[@AztecWarrior69_69]

Yes you can. You can do it with a TPDT relay, or three relays, or two relays and a diode or just two relays.

[@shyamlallal5469]

what type of relay you used? please explain.

[@mikmaster63]

Metra Install E-123 Bay Tyco Relay 12 Volt 30 Amp Each a.co/d/fOHUpj3

[@mikmaster63]

I use 12 volt 30 amp relays usually. This is one brand I have used.

[@shyamlallal5469]

@@mikmaster63 thank you for your quick reply

[@oscargarfias9379]

How I can use a toggle switch instead of button switch?

[@mikmaster63]

This maybe kzbin.info/www/bejne/gH2Xk2Wuo91sebc

[@mikmaster63]

kzbin.info/www/bejne/baS0koZsn7JmjJY

[@mikmaster63]

Maybe one of these will help kzbin.info/www/bejne/lYXSpYCYl61ko9U

[@mikmaster63]

I think I know what you are looking for. Operate it with toggle and switches to auto stop??? It will take me a while to make it working 7 days a week right now.

[@oscargarfias9379]

Thank you so much I appreciate

[@rogerbrowne5514]

But you still have to push a switches to make it work.

[@mikmaster63]

???