Review: Swageless Fittings for Wire Balustrade | HAMMERSMITH

If you are looking to do some wire cable balustrade and you don't want to buy a tool to swage (crimp) the fittings, then perhaps it is worth taking a look at our range of SWAGELESS fittings. This video review shows the different fittings available and gives a demo has to how they work.
For a closeup shot jump to: 2:22
These fittings are available on our online shop. Click the link that follows: www.hammersmith.com.au/hs_pro...
The 3.2mm wire cable that is shown in the video can be found on our website here: www.hammersmith.com.au/hs_pro...
--------------------------------------------------
The Hammersmith DIY channel is the KZbin channel for the Australian business, Hammersmith.
Situated in Adelaide, Australia; Hammersmith was established in 1946 as predominantly a wood turning company, but in more recent years has expanded the range of products that it sells to include building, staircase and furniture components in both timber and steel.
All of these products can be found on our online shop, and can be delivered to anywhere in Australia.
Shop online : www.hammersmith.com.au/hs_pro...
Learn our history : www.hammersmith.com.au/hs_about
Follow our blog : www.hammersmith.com.au/blog
Connect with us on Facebook : / hammersmith-diy-produc...
Connect with us on Instagram : / hammersmithdiy
Check us out on Pinterest : www.pinterest.com.au/hammersm...

[@K3BANG]

This is great, exactly what I was looking for as I only need to run 2 balustrades!

[@tongchai1990]

Thanks for your video. Very informative.

[@tokyoobro]

Thanks mate. Very useful information and video.

[@hewellwood]

Great vid explaining swageless ballustrade fittings. Just bought the swageless version but with tapered jaw clamp ends from Pinnacle. Seems like great quality gear, just wanted to see a vid on how exactly to best make these work for a tight finish. I would have liked to see a vid showing the tapered version in situe ie between a couple of posts showing exactly the best way to get the tension you need. I figure I need to undo the turnbuckle as much as possible, cut the cable to length and see if it tensions up nicely. I'm sure it will be fine, thanks for the information Hammersmith DIY.

[@NevH-mg5zv]

Thanks very informative 👍

[@ozskipper]

@4.18. There is a slot on the female that allows for the "other" spanner you were meant to use 😉

[@bobpattison1739]

Been hearing about people that experience rusting of the stainless components. Looking to install this at a beach house and curious if that problem has surfaced and is so has there been any improvements to the technology that elevates such an issue? Thanks for your help.

[@HammersmithDIY]

Stainless is not a set and forget product. If you don’t keep it clean then you will have rust issues, particularly when used in a coastal setting.

[@leileizhang2391]

The material of 316 is fine.

[@bobpattison1739]

@@HammersmithDIY is WD 40 effective in that setting or is there specific products for the job. Thanks again for all your help. Stay well

[@HammersmithDIY]

@@bobpattison1739 I am not sure. We sell a product called Peek polish, but no doubt their are other products which work well also.

[@bobpattison1739]

@@HammersmithDIY share your site where I might be able to make a purchase. Thanks

[@paulalderson6920]

Why are the two ends different? Couldn't one type fit both ends?

[@HammersmithDIY]

The longer version could be used on both ends, but the short version allows you to save money, as the long version is more expensive. You need at least one of the long version as it is required to give you the tension that you need to add to the wire.

[@GlobalTriathlonNetwork]

Can I cleanly cut this cable with grinder? What blade?

[@HammersmithDIY]

We don’t recommend it. It tends to want to fray when you use a grinder or blunt cutters.

[@GlobalTriathlonNetwork]

@@HammersmithDIY what kind of cutters?

[@leileizhang2391]

Customization