Making of 210x310cm (6,8x10,1ft) CNC Router

[@protomake1349]

The soldering done at 15:50 to 16:00 was a "cold" solder joint which will fail with vibration or movement. What you want to do is heat up the solder cup with the tip of your iron, fill the cup with solder, then put the wire fully into the solder cup. Before you remove the soldering iron you want to see the solder wick up the wire slightly (and produce a nice fillet) then remove and allow to cool. Will be a superior solder joint. Very cool (and VERY big) CNC router!

[@diyprojectchannel]

You did a really good job! Nice machine. Hope to see it working :-)

[@scardera]

Im planing to build my own, but definitely not that big! Good work, must have been fun putting it all together!

[@scardera]

@@kalpeshwani8520 no one asked.

[@EletricistaEmBrasilia]

what a great job. I'd like to know how it is going after years of work. And it'd be interesting if the creator give some insides about what he would change to improve the machine after years of working.

[@raifhanna1120]

Great job ,May you publish wiring schematic and mention what breakout board, please

[@subice21]

Beautiful and elegant work!

[@GBWM_CNC]

Great machine. I do really appreciate sharing.

[@scotty362100]

Nice project! Can you tell where you got the 27x170 profile for the Z axis, I have looked everywhere, and can't find anything like it! It is PERFECT for Z axis plate.

[@MrBjorntsc]

I cannot find it either. Any luck?

[@Jur4S]

@@MrBjorntsc me2 hope someone help

[@mehdja9525]

Just a Tip:The side Parts for Y Axis are very Thin (Black Parts) . you will have a lot of vibration and inaccuracy in y direction milling Hard Material.

[@gaiustacitus4242]

The side plates could be made more rigid by welding on reinforcing ribs at 90 degrees and interconnecting them.

[@kalpeshwani8520]

* What a presentation & music too moving ahead enthusiastically ....

[@flikflak24]

where did you get the alu bearms thats on top of the steel frame ?

[@managerlmw5382]

Great project. I don't see the 27*170 profile source on your bill of materials.

[@neumero4te]

Try CNC Cat 27x170 Six Slot

[@himzo05]

Is that Arel spindle same as Hertz spindle? They look the same.

[@joppepeelen]

where did you get some of the more basivc materials from ? like the angles and the plate to be used for the X axis ?

[@revocnc]

Hello. www.segaotomasyon.com/urundetay.445.90KP%20K%C3%B6%C5%9Fe%20Ba%C4%9Flant%C4%B1.html www.doguskalip.com.tr/Product/1122/27x170-surface-coating-profile

[@peggo-channel]

Beautiful and funny to see how complicated is to make a rotating bit move around... haha

[@tonyfremont]

At least half of the wiring is safety/limit sensors to keep it from wrecking itself. For something built to work soft materials, it seems a bit more than just sturdy.

[@inhbaobui1757]

I can not download the material of yours? Could you please help me? thank you very much

[@mozg.krasnodar]

Залепательное видио,вот только в конце плата управления висит криво и самая дешевая Мач3. А так много познавательного увидел. Чуваку лайк .

[@thanhnhanhuynhnguyen3652]

Fantastic job!

[@samking1614]

Great work guys. That is a very big and strong machine. I have one question, please where can I get some of that Aluminum extrusion you have for your Z Axis plate. I really need such an extrusion. Can you please who me where to buy one? thank you.

[@archys7]

I would like to know too. Thank You.

[@reissevdalilari3501]

işte Recep Tayyip Erdoğanın ülkemizi getirdiği ilerleme. işte büyük türkiye, Güçlü türkiye. Darbecilerin, solcuların, kemalistlerin at koşturduğu 90 larda ülkeye bir çivi bile çakan yoktu. şimdi Türkiye büyüyor güçleniyor inşAllah. İHA lar, helikopterler, tanklar, Otel gibi hastaneler dünyanın en büyük yapıları. Allahu AKBAR.

[@trendremixx]

here www.doguskalip.com.tr/Urun/1122/27x170-yuzey-kaplama-profili

[@a.ekbergokay6541]

@@reissevdalilari3501 çoook ileri görüşlüsün gördüğün ufuk görünmüyor.

[@ozkanylmaz8490]

​@@a.ekbergokay6541 Siz olayi anlamadiniz heralde, kimse 27x170 extrusion profili bulamamis. Bunu ureten firma da yerli. Bundan dolayi mutlu olmamak mi lazim. Niye bir övgüyü haketmiyor bu millet. Niye surekli yurt disi ozentisindesin ki. Adam guzel seyler soylemis gurur duymus. Niye dalga geçiyorsunuz. Napalim uretmesinler mi?

[@texasbowhunter2509]

I like the "Z" backing plate you have shown as well as the backing plate for the spindle...Is that your design or are those from the manufacture? I sure would like to acquire a set possibly...Thanks for sharing

[@revocnc]

Hello. You can find it from the link. Best regards. www.doguskalip.com.tr/Product/1122/27x170-surface-coating-profile

[@TomFYouTube]

PLEASE... I would like a machine that is 350cm x 100cm. What kind of resolution, repeatability and backlash are you getting with your rack and pinion? Thank you Awesome job by the way.

[@wingez2445]

Good job 👍

[@othoapproto9603]

All that money and time and the gantry verticals are 1/4 plastic?

[@highpointfurniture]

Hi have you made any alteration to the machine or any updates would be highly appreciated, Im starting to build one and any additional information would be highly appreciated

[@ibrahimgirgin4822]

Good working...

[@ben.deniz08]

Hocam merhabalar çok basarili z modülünde kullandiginiz plakayi ne diye aratirsak bulabiliriz birde yatak olarak bf15mi kullandiniz

[@revocnc]

Z eksende kullanılan profili Doğuş Kalıp'ta yüzey profili olarak bulabilirsiniz. 27*170 idi yanlış hatırlamıyorsam. Yataklama için BF15 kullanılmıştı.

[@lmjoshea5915]

Hi Super looking machine.. Thanks for Sharing.. This is a machine i will be purchasing this year, could you please tell the cost.. Thank you..

[@halilibrahimpolat5679]

Kolay gelsin hayırlı işler ustam öncelikle tebrik ederim çok başarılı bir performans bu tür ve benzeri hiç bir video site yok sizden başka link den dosyanızı indirdim ama STP olmadığı için açamıyorum STP dosyasını paylaşırsanız çok sevinirim İyi çalışmalar başarılarınızın devamını dilerim iyi günler

[@erolkaragoz1685]

Which spindle should be used for plastic cutting?

[@revocnc]

Merhaba Erol Bey. 500Watt ve üzeri tüm spindle motorlar, takım çapını küçük tuttuğunuz sürece plastik işleme amaçlı kullanılabilir. 1-1.5 kW civarı bir motor ise daha garanti bir çözüm olacaktır. Daha büyük kesim operasyonlarında ise 2.2 - 3kW civarı bir motor tercih edilebilir. İyi çalışmalar dileriz.

[@bwcdevices3028]

Brilliant - thanks

[@farizfadli9172]

How much the cost for all those kits..

[@chandlerbing700]

What was the approx. Cost you incurred ?

[@robertschwarz1795]

What is that aluminum extrusion profile you used on the Zaxis? It is recessed in the middle to make space for the ball screw. Can you share a link where to get it?

[@revocnc]

Hello. You can buy it from here: www.doguskalip.com.tr/Product/27x170-surface-coating-profile/1122

[@GAETANOIERA]

Salve vorrei sapere quanto costa un pantografo router cnc 4 assi 3000 mm x 1500 mm completo di software ed optional Spedizione in Italia. Grazie.

[@RajeshSharma-iu8cp]

Timing Pulley dimensions are missing from description

[@yuvashankar7820]

Pulse per revaluation and pulse mm calculations please🙏🙏send me Sir

[@ferhatbilseloglu7748]

HARİKASIN : -)

[@houcineth2918]

how much like this .?

[@PTinvest]

how much cost and can you make me offer

[@atillasinan1465]

Merhaba iyi günler kolay gelsin sağlıklı bir yaşam dileğiyle böyle bir makina maliyeti ne olur acaba yardımcı olur musunuz rica etsem.

[@revocnc]

Merhaba. Videonun açıklamasındaki malzeme listesindeki ürünleri araştırıp yaklaşık maliyet çıkarabilmeniz mümkün. Satış fiyatı soruyorsanız da biz bu boyutlarda makineler üretmiyoruz, o yüzden yardımcı olamayız. İyi çalışmalar dileriz.

[@TheOffbeatVibes]

Please share wiring diagrams.

[@guangzhouminxuelectronicte1242]

Cooperation request: Hi dear sir,could you tell me how to contact you?we want to cooperate with you,look forward to your reply,thank you.

[@revocnc]

Hello, what kind of cooperation do you think? Contact via, [e-mail] Thanks.

[@guangzhouminxuelectronicte1242]

@@revocnc Hi dear Mr.REVO,we sent an email to you already,please check and wait your reply,thank you.

[@mrmakinist]

eeee artik devami yokmu be

[@kraustman2285]

Elinize sağlık. Ustam size nasıl ulaşabilirim bitirme projesi için bilgisel yardımınıza ihtiyacım var da

[@revocnc]

Merhaba, www.revo.com.tr/tr adresindeki iletişim bilgileriyle bize ulaşabilirsiniz. İyi çalışmalar.

[@reissevdalilari3501]

işte Recep Tayyip Erdoğanın ülkemizi getirdiği ilerleme. işte büyük türkiye, Güçlü türkiye. Darbecilerin, solcuların, kemalistlerin at koşturduğu 90 larda ülkeye bir çivi bile çakan yoktu. şimdi Türkiye büyüyor güçleniyor inşAllah. İHA lar, helikopterler, tanklar, Otel gibi hastaneler dünyanın en büyük yapıları. Allahu AKBAR.

[@TrismegistTonianAtton]

Oh my God. My heart bleeds from such vandalism.

[@marcsullivan3479]

Im curious what you considered vandalism (im new to cnc)? I thought it looked perfect. (maybe the stepper motor mount could be improved upon)

[@pauldupuid6349]

Coming from an industry that utilizes lasers, your statement regarding material waving due to laser cutting is both misleading and inaccurate. If you receive material that has a wave to it, the laser is undersized for the application, and chances are your dimensions are off. Lasers rely on heat in direct relationship to speed. Wave is caused by decreased speed and high output. Which is why it is important to have the proper tool to do the job. The chances of your 8mm or 10mm plate being warped or wavy are almost nonexistant.

[@zoainat100]

Salam, Why the www.revo.com.tr/ is not working yet!

[@2010Edgars]

Nobody works with cm. Use always mm in title.

[@GAETANOIERA]

Ok 2100 x 3000

[@trendremixx]

I can send the used materials in the video. If anyone need.

[@danilomacanovic]

All that professional mechanical components and still using LPT interface for Mach3 , also belts seem too narrow , welding suspicious. Pile of nice parts thrown badly together thats what I see.

[@aliselviCNC]

tools is izeltaş 🇹🇷🇹🇷

[@lalshankarsuthar1199]

I want whatsapp e e

[@css5168]

Что ж вы такие криворукие?! Что сборка,что электромонтаж - как школьники.