WPL C24 Rc Crawler waterproof tips and tricks!

[@ThomasPowellNZ]

As long as the snorkel's above water, it's all good.

[@RunThatRC]

that's right! hahaha.

[@wazeFPS]

Water break ins were on the old school racing days to get every little performance out of the motor, but it wears down the brushes half way just from one break in, generally yes the motor will be fine but it will wear your brushes down this is because the coating that forms usually will cause very little abrasion of the brushes but with water well it’s not there so you’re just wearing your motor down way faster

[@JedociderShou]

Found your waterproofing video! Thanks for the tips!

[@mikepereyra6419]

thank you dude for the tricks n tips, I purchased my first MN 99 awesome rig

[@RunThatRC]

Nice! The mn models are decent rigs.

[@fixedgear.fl.4225]

T-9 is also great for outside/internal protection. Thanks for the tips. One day I shall try myself. Great video. I like your channel. You explain well.

[@RunThatRC]

Thanks! Appreciate the support!

[@TheXanUser]

I prefer to use conformal silicone. it covers much easier and can be removed later. Im very surprised that ive not see anybody that is direct soldering their servo wires to the receiver.

[@RunThatRC]

I just have a lot of plasti dip already on hand thats why i use it. I was going to solder my servo wire and motor wire as well but decided not to because i may move the esc combo to another build and prefer just the plug for now.

[@grayhancock6953]

@@RunThatRC how do I put the sock on the engine??btw I have a trx4 blazer so??

[@FastDuckyGaming]

Awesome! Your channel is growing fast! I wanna ask u a question, Is the b36 better or the c24?

[@RunThatRC]

Out the box the b36 is a better buy. If you like to modify and like me love Toyotas! Then the c24 is a good truck to upgrade because it has 4 link suspension and is better off road! Also thanks for your support! Hope to get better at it as I go!

[@FastDuckyGaming]

RunThatRC thank you!

[@ighfirlee]

Silicone sealant, the stuff people use for plumbing. Good as a seal.

[@RunThatRC]

that stuff works as well.

[@M.TTT.]

Did you raise the transmission like 1/2"?

[@RunThatRC]

Just about.

[@leewheaton8498]

You do know fresh out of the box RTR wpl c24 and such vehicles are already waterproof. Good tips though man, thanks for the video.

[@RunThatRC]

I wasn't aware that the newer RTRs are waterproof. None of mine seem to have been so I wanted to be safe. I will contact WPL and check if they are. I know the Res v3 esc receiver combo is water resistant but not waterproof. Thanks for stopping by!

[@dinslax5270]

i have traxxas trx4 defender, its already waterproof but i coat the circuit board using a 3 layers of clear spray. better safe than sorry. that being said, one of my friend got his trx4 short circuit after dipping the car in the water. turns out, the waterproof seal box of the receiver is loosen over time. so spraying the circuit board is a security measure.

[@gabrielsilvaz4199]

I have a much more effective way to waterproof the ESC on my Quick tips and tricks video series I show how I upgrade that kind of ESC by using a makeshift injector to inject a black rubber sealant. It’s for more superior than Plasti dip it’s called prematex Black rubber sealant it takes longer to dry but is way more heavy duty plasti dip is great don’t get me wrong but for that kind of ESC injecting the black rubber sealant completely covers the entire chip inside the shrink tubing cover giving you a worry free Seal. I’m sure you’re Plasti dip is working just fine but On the other hand Plasti dip is easy to remove and scrape off accidentally That other stuff that I’m talking about is on another level but it also cost 14 times more at $9 for 1.5 ounces roughly enough for 8 or 10 ESC waterproof jobs.

[@RunThatRC]

Will give it a try one day!

[@ighfirlee]

Wont rubber or plastic dip makes the circuit board hot?

[@PedroSilva-yv5df]

Great tips!! How do u isolate the little hole in the gearbox!? Or the grease inside is enought!? Thanks.

[@RunThatRC]

You can apply waterproof grease on the hole, shafts and around the seem where the case splits for extra peace of mind. I just fill it full with grease and the gears spinning should sling it around everywhere and make a pretty good seal.

[@den41400]

Just a suggestion drop of candle coat the chip with it and you have a waterproof esc mod.

[@nixonrogers4356]

Do you have Any suggestions for good waterproof rock colors

[@RunThatRC]

hobby plus makes some fully waterproof crawlers. RGT makes some too. If you like these wpls they arent hard to make waterproof.

[@nixonrogers4356]

@@RunThatRC ok Thank you

[@nixonrogers4356]

@@RunThatRC How do you know which ones are waterproof

[@rcnoob6231]

Hey dude just bought the c24 was just woundering if you have a link to some good shocks thanks!

[@RunThatRC]

I actually don't because I haven't used any. I'm still on the stock shocks. I know most people have to relocate shock placement to install some oil shocks.

[@johnpaulpunla3357]

Did you open the servo ang put waterproofing inside or you just cover it outside?

[@RunThatRC]

also covered inside. Cover the circuit board and the case when you close it.

[@johnpaulpunla3357]

@@RunThatRC what about the battery do.i need to do something?

[@RunThatRC]

@@johnpaulpunla3357 just as long as your using regular lipos and lion batteries your good to go. If its a smart battery or one with a chip then maybe waterproof it. Most lipos are waterproof inherently. You can plastidip to protect the leads if you want.

[@zurstfg1016]

Will wd-40 work

[@RunThatRC]

my friend uses wd40. I use penetrating oil. We have been ok with both.

[@יוסיד-צ7ע]

what about spraying some silicon spray or something like that? on the engine

[@rob5188]

hey, what if sand gets in my chassis. Because today I took it out on the sand a couple times, and then all of a sudden it started to lock up and it would go anywhere even when i moved the tires it was locked, but then over a while it got un stuck, is there anyway to clean it?

[@RunThatRC]

if you play in sand or mud the motor can get damaged and stuck if your not protecting it. You should always rinse and dry your truck after running in water specially mud and sand. taking apart your axles and clean regrease then that should keep it running good.

[@rob5188]

@@RunThatRC but wouldnt the water get into the motor?

[@rob5188]

and also, should i take apart the differentials with a screwdriver to get out some of the sand stuck on it, usually ive just been gently watering it down and thats been getting some of the sand off but ive been careful not to get it in the motor. I dont have grease so I dont know where to get it

[@RunThatRC]

@@rob5188 yes I recommend opening it up once in a while and give it a good cleaning. Any general purpose grease or waterproof grease will work.

[@rob5188]

@@RunThatRC okay thanks, one last question would oil work as well as grease?

[@leotynee]

Sir got a question if you dont mind. When you run wpl or mn rigs in water, how do you waterproof the battery? Thanks

[@RunThatRC]

Lithium ions can be submerged but make sure to get them dry after you run because they may start to corrode. Lipos are the best option for water runs they are inherently water resistant. battery cells are sealed and water runs dont seem to affect my lipos. Just dont forget to dry your batts after your run and thry should be fine.

[@leotynee]

@@RunThatRC i see. Great info. Many thanks!

[@leotynee]

@@RunThatRC oh, another question if you don't mind... 😁 Can the stock motor of the mn99 take on a 2S lipo battery? Or should i save it when i eventually upgrade to a 370 motor? Thanks again!

[@skidaddleskadoodle563]

For the marine grease, would I add it with the grease that came with the axles?

[@RunThatRC]

I would degrease and then marine grease.

[@pateickflynnjr3454]

I have a complete stock wpl c24 so all I need to water proof is just electronics and because my truck is stock what would I need to lube up after going through water

[@RunThatRC]

just use some waterproof grease on the axle gears to help from rusting. just waterproof electronics and servo then you should be good to go. Don't forget to run it out of water after to warm up the motor that helps dry it out.

[@tonygSDWR]

Finally, someone justifying having the snorkel on there, ha!

[@Jacobp_RC]

Its not a snorkel lol its an filtered air intake for the engine😂

[@yakagaming8592]

I just bought a c24 and your channel helps alot one sub from me .

[@RunThatRC]

I hope you enjoy it. They are fun to mod and surprisingly capable little guys.

[@radunit4805]

Is that a kawasaki ninja model? I think we have the same one. Though mines kinda wrecked lol

[@RunThatRC]

it's a model of my actual bike. That's why I purchased it.

[@MrMosinNagant1937]

Liquid tape works too

[@RunThatRC]

yes it does work.

[@747fa]

Hi. Just wondering how you water proof the battery connectors?

[@den41400]

I thing its fine for the connectors to get wet just saying

[@TheActionBastard]

You could make a boot of some kind if you were really concerned, but I think that like they said the electrical conductivity of the water and the large gap between the contacts (as well as the pressure fit/seal from them being connected) would just not be conductive enough to draw an arc when there is a much better path through the wiring. I prefer to make a ghetto boot or wrap my connectors or just... 3d print some crap so I can seal things in boxes and just run wires out with silicone seals around the wires.

[@RunThatRC]

Don't know why I'm only getting this notification now. Sorry for the late reply. The connector for your lipo or lion batts are fine the way they are just don't run in salt water or they will rust quick.

[@747fa]

Many thanks to you all. 👍

[@kylarbolding117]

Would candle wax or a rubber glove work too?

[@RunThatRC]

Ive heard of both being used but I haven't used those techniques. I use to wrap my receivers with balloons back in the day but I have a lot of success with plastidip. Also I already have a bunch of the stuff.

[@moaiking_]

Can stock drive in mud and water?

[@RunThatRC]

no they are not waterproof out the box but can be easily made waterproof at your own risk.

[@JedociderShou]

I'll try using hot glue since I don't have plastidip. Is it okay for the battery to get wet? Also is the servo safe without waterproofing it?

[@RunThatRC]

The servo is not waterproof I recommend sealing it as well. It open the servo and seal the electronics board to be safe

[@RCWithPopeye]

I loved it. I have also lots of these

[@RunThatRC]

Yes these are cool. And the stuff you make out of the parts are great! Keep it up brother!

[@FuntimesAussie]

Will mesh work?

[@RunThatRC]

Definitely, just make sure the mesh is a fine mesh that won't let debris enter the motor.

[@humancalculator711]

what about lion batteries

[@RunThatRC]

I haven't had any issues with my lion batts in water so far.

[@M.TTT.]

Where do you get the nylon sock? I just built my c24 2 speed today, needed some modifications to get it together but not bad.

[@RunThatRC]

Nice! Just any cheap mesh sock will do as long as it protects from getting debris in there.

[@M.TTT.]

@@RunThatRC hmm alright I'll have to look around. And lol I already broke the crappy metal drive shafts I bought the URUAV ones I think. They just fell apart. Junk. Ordered some that look like yours off amazon.

[@rustytoolman4912]

Do the C24 kits come with a three wire or five wire servo? thank you

[@RunThatRC]

All the kits and newer rtr WPLs I own all have 3 wire servos.

[@rustytoolman4912]

Thank you, I knew you were the person to ask. I really appreciate your video's, thank you!@@RunThatRC

[@RunThatRC]

@@rustytoolman4912 Thanks I appreciate it and glad the enjoy the videos!

[@MKHITARIANVahram]

Super 👍😀

[@Ryderknoblauch509]

Wait if I didn't waterproof my wpl then how the hell did i submerge it 100 times

[@RunThatRC]

that's pretty lucky unless your using waterproofed electronics. Is your wpl a Ready to Run?

[@brandonhehn5157]

Do you have any info on the WPL 90/91 reversal gear assembly?

[@RunThatRC]

I don't believe I know what the 90/91 reversal gear assembly is?

[@brandonhehn5157]

Yeah.., I really describe it wrong. Sorry. Its a Banggood product for WPL models just called reversal gear box.... I wasnt sure if you have used it before.

[@yesus00]

I put all electronic inside of a ballon!

[@RunThatRC]

definitely works! I've done it several times before.

[@M.TTT.]

What size or type of batteries do you usually run on these trucks?

[@RunThatRC]

Anywhere from a 2s lipo 500mah to 1000mah. Or lion 500mah to 1500mah 2s as well.

[@M.TTT.]

@@RunThatRC ah okay, I have a 950mah 2s lipo already, so I'm hoping it fits and lasts a while driving in the c24. Thanks!

[@RunThatRC]

@@M.TTT. plenty of runtime with a 950mah 2s.

[@jeffreyjrjustin8614]

What tires you use

[@RunThatRC]

the bluenones has stock kit tires and the white truck has MN Model mnd90 kit tires and chassis underneath.

[@sbrc8725]

Do MN tires fit on the C24-1?

[@RunThatRC]

they do but without a lift they will rub when flexing.

[@cyberesi6]

what about the battery?

[@RunThatRC]

lipos and lions do ok submerged in water. they are completely sealed cells and are inherently water resistant. Always try and dry your batts after water runs to prevent wire corrosion and unplug them from esc asap when done.

[@rcmania8731]

oke good

[@froilandelacruz5493]

how about the power supply?

[@RunThatRC]

Lipo batteries are inherently water resistant. You can plastidip where the leads come out but I tend to just dry my batteries after running them so they don't corrode.

[@froilandelacruz5493]

@@RunThatRC oh i didn't know that.. thank you.. subscribed!!!

[@RunThatRC]

No problem! I try to answer every question If I can so if you have anymore let me know and I'll try and help!

[@M.TTT.]

Found it!

[@thatmguy3687]

How about wax

[@RunThatRC]

never used it but heard of people using it. I usually use plastidip and even epoxy before I knew about plastidip.

[@tracydavis96]

I use pantyhose for mine Great filters lol

[@samsonfpv8902]

Corrosión X bruh

[@riclynsonhenry9201]

L