RV Roof Replacement 0n 2011 KeyStone Alpine

Please understand that these are not DIY videos, also we shy away from giving advice because we do not know what materials each person is working with. We do not sale any products, nor do we provide quotes on social media, if you are looking for a quote please email us at [e-mail].

[@rickvititoe3814]

Great job. Very informative

[@RVROOFINSTALL]

Thanks for watching!

[@gregbetts8057]

looks like robertson fasteners , canadian ?

[@nevadalamont82]

That is great where is your business located

[@RVROOFINSTALL]

Fort Oglethorpe Georgia. Thanks for watching.

[@rubberdiscoduck]

I'm a firm believer in the slop and thin technech. Another awesome video.

[@Theatrelove]

I will say your the best in the rv roofing world , i did my roof the same way after watching all your vids . That being said dont cut your quality of work with self tapping screws for the bottom ac flashing flange , im dont thinl you sealed them also they will shake lose overtime . Tig weld or braze your metal to metal flanges . Also where the rain gutters .

[@pestera6]

Thank you for sharing information, big help here as I'm new to rv world and trying to replace my leaking roof on 21 feet motorhome

[@pcofranc]

First honest comment I have heard on Dicor junk and way over gooping all the flashing. The obsessive attention to even the smallest details is breathtaking.

[@proteus2901]

im in Austin texas have a 2012 redwood 36RE needs a new roof looks just like the 5th wheel Alpine found a small soft spot where the sattilyte wires go in to the right of the air condioner needs some repair work and a leak near a corner also ,where r u located?

[@RVROOFINSTALL]

We are located in Fort Oglethorpe, GA. Just a few miles south of Chattanooga TN. 423-475-7663.

[@2servenprotect327]

Great video. Im in the process of repairing my roof on my 5th wheel. This was a great video on the process. Just wish i could afford the services of getting a brand new roof. But your video gave a good step by step if you will on the repair process. Great job. Just subscribed.

[@RVROOFINSTALL]

Thanks for watching.

[@sandiegojody]

Hello, i am in the process of replacing my epdm roof on my 17' travel trailer, and i plan to replace it w another epdm rubber. Or should i go with a TPO roof? Is there an advantage one over the other? Thanks and great video!

[@scottdowney4318]

Interesting job. How about fiberglassing the roof? I suppose that would be more work. Watching you I was thinking of buying an expandable RV about 26 foot maybe from 2015 to 2018 and was wondering if they had improved their construction.

[@techi3075]

Great work, looks like a quality install.

[@RVROOFINSTALL]

Thank you for watching.

[@agentorange2554]

Absolutely fantastic work, far superior to the factory roof. I'm totally knocked on my butt.

[@Hundert1]

I think if the RV had been made better the roof should be made to last a lifetime. Thanks for your video and efforts to help us out. Happy Easter Season 🌴☀️🕊🌴🌴🐣🐤

[@RVROOFINSTALL]

They're all the same. I don't own one. Thanks for watching.

[@Hundert1]

@@RVROOFINSTALL Yep, some travel trailers have fiberglass or aluminium roofs. I think these are a more durable roof. Thanks

[@RVROOFINSTALL]

@@Hundert1 Fiberglass or aluminum are no better. The problem isn't the actual rubber or membrane, it's the fact that there are no curbs or boots. That's called detail. That's where the leaks start....from the protrusions.

[@Hundert1]

@@RVROOFINSTALL So the rubber membrane needs to be curved upwards like an inch or so around every roof vent, skylight, A/C unit, then caulked? Instead of just laying flat and caulking on top ? I'd still feel safer, especially on a full walk on roof, if the roof were solid fiberglass or aluminium. A rubber membrane just seems too easy to puncture by so many simple accidents not requiring much effort. thanks again 👍

[@RVROOFINSTALL]

@@Hundert1 rubber...EPDM...Is the cheapest in product on the planet. We use 6o mil TPO. We have replaced many fiberglass roofs. They're on the channel. Thanks for watching. We just try to show where and how failure happen and why.

[@brianhoward438]

Wow very cool to watch.Whats a roof job like that cost?What a Awesome job.you guys are very meticulous.I wish you were closer to me to do my 5th wheel Toyhauler.

[@theodorecarbajal2975]

Great looking roof

[@John-vj7ie]

Thanks for the video's I've watched a lot of them I am putting a new liner on my 97 Dutch star and my question is on the front and rear end caps should I put the liner underneath or on top mine both were under I was going to go under on the front and over on the back thanks John

[@RVROOFINSTALL]

The way you were going seems logical. You need to protect the roofing from the siding whether it's over, under...vise versa. Thanks for watching

[@robertnewman1593]

Wow, wish these campers came this way. Awesome job

[@RVROOFINSTALL]

You mean with qulaity craftsmanship and quality products folks have thought they paid for??... LoL. Corporate America will pay a man 6 digits a year to seek out where they can save 1 cent! These campers are getting worse by the year. I don't own one. I'll have to build mine. Thanks for watching!

[@robertnewman1593]

@@RVROOFINSTALL YES ! On quality craftsmanship and products. I own a 5th wheel and have fixed a lot of issues on it. I highly doubt I will purchase a new one anytime soon given all that we have gone through with ours. I just last fall installed hydraulic disc brakes on it myself. I have never felt confident with the electric brakes. The 5th wheel is now 10 years old but looks new. I know sometime I will need to replace the roof. I doubt I will do as great a job as what you do there. Great video though. Thank you

[@davidrogers4527]

Absolutely beautiful.. how much would a job like this cost?

[@LuisNY]

Hello... thanks for the videos, great information there! I have a pea size hole on the rubber of my roof, it has been in parked for the past 6 months and I didn't see that hole there before winter... the wood inside is already curling and softer than the rest... Under the membrane is a little wet, should I just patch that hole? Any suggestion on how to dry it before patching the hole?

[@RVROOFINSTALL]

You could patch it but it won't be a long term fix. If the wood is dry you could inject some caulk under the membrane and then out a roof tape patch, although you need to clean and prime the roofing membrane. Second option...file a claim with you insurance company.

[@bigoldal2436]

What do you use for securing decking over delaminated decking after removing the delamination ? I used construction adhesive previously on my 2004 R Vision but now I am doing TPO again on my 2004 Jayco Designer ( BTW Jayco lied about the thickness of the decking, they said 1/4" and I don't even think it's 3/16ths ) but it looks like the M1 is a superior product . I probably use exterior luan as before (1/4" .).Actually I prefer fiberglass roof but even the old pittsburg lock seam aluminum roof were better than rubber if you resealed seams every year. GREAT VIDEO'S !!!! Sorry a little long.

[@RVROOFINSTALL]

We shy on quoting jobs on social media. Each job is different so we like to know all what you got going on. We advertise everywhere because we are the only certified RV roof shop in the country and from what I'm told there isn't any shows that rebuild like we do. Folks come.from Canada, Florida, Louisiana, New Mexico....but to answer your question we are generally less expensive than an RV center. Thanks for watching!

[@snapforth]

Can you tell us what the bill was on this unit?

[@jasontindal2525]

Great video. just bought a 34 ft TT. I have no idea what has been done to the roof. What do i need to do to make it last the longest? seal? condition? I have no idea, thank you in advance

[@RVROOFINSTALL]

The coatings and conditioners are an RV scam to stay st6ick to your wallet. Nothing will make it last longer that we know of...not on an RV. Keep an eye on the caulk concerns we show on the videos. Save for a real roof. You'll need one. With any luck maybe a tree will hit it or you hit something, then your insurance will pay for it. Thanks for watching!

[@alisonmcirvin4763]

Great detail in your video, thanks! Where can I purchase the flashing that you install around the AC and all the roof vents/caps? What is is called? Thanks!

[@frankenstein3163]

My EPDM or the other ruber roof looks ok. But I have a spot wear it looks like a branch poked a hole and than was calked(lap sealant). I just noticed that the ply wood it badly rotted about 1 foot across. it feels like some of the wood framing might also be rotted. Should I just peel the roof back(can it be reused ?) and replace the wood or just do the EPDM rubber roofing coating system ? I live in it and have lots of rain coming withing a few weeks. I can get a carport tent with clear tarps to work on it.

[@RVROOFINSTALL]

The rubber roof is not worth salvaging. I'd recommend tearing it off, make repairs and adhere a commercial membrane, that is if you are doing this yourself. Thanks for watching.

[@cliftonharper8444]

What roofing membrane material, and self leveling lap sealant are you using? I have had PVC and luan sheets glued over sub roof material.

[@Dave-ld3dr]

If you don’t recommend Dicor then what do you use?I need to purchase some.Are you a fan of eternabond?

[@RVROOFINSTALL]

Nothing will stick unless it is prepd. Needs to be primed. All that stuff you can find at your local commercial supply house. Thanks for watching.

[@Dave-ld3dr]

@@RVROOFINSTALL can you give me any names of the products?I was going to try to order them off Amazon.Thanks.

[@RVROOFINSTALL]

@@Dave-ld3dr any membrane primer will work. Then Rapid at Home Depot in the concrete section.

[@Dave-ld3dr]

@@RVROOFINSTALL Thanks

[@RVROOFINSTALL]

@@Dave-ld3dr Dicor is made by Carlisle Syntec. Carlisle makes a commercial rubber lap sealant if you want to use that. I hate to give advise because I can't see what your working on and if it fails you'll be shaking your first at me thinking I'm giving you bad advise. If no it were mine I would take the time to get the Dicor off. Mineral spirits will break it down but makes a mess. Once clean, remove and clean the vent underneath as well. Wash well with denatured alcohol to get the spirits off. It leaves a slick residue. Once clean prime the membrane and the apply a very generous bead of the Rapid non sag to the bottom of the vent and settle the vent back into place. The idea is to have about a ¼ inch cushion if caulk under the vent. Let cure, then replace the screws. Out a do. If caulk where the screws will go and torque the screws down so they're right but not trying to crush anything too tight. Then go around the perimeter of the vent with a second strike of Rapid. It will e time consuming for sure. If you ruo the roofing you can use the eternabond as long as you prime the roofing. Then prime the eternabond where caulk will be applied.

[@r32rtb]

What adhesive do you use for the membrane to the decking? Looks like you do a great job and take your time...

[@RVROOFINSTALL]

We use GAF TPO adhesive

[@ericstyer2890]

People do not realize to install these per manufactures instructions to keep warranty you are using expensive products. I’m not even talking about the field sheet. The sealant, primer, boots, pour sealants, all have to be TPO grade and done properly. I just watched a hack install his like EPDM. Dudes gonna be disappointed when his new roof leaks in a couple years. The curbs are a crucial necessity but I bet DIYers rarely have installed their own much less hot air welded anything. There’s a reason people pay pros to do their craft. Kick ass vids.

[@RVROOFINSTALL]

We are the only certified RV roof installers in the country. We can extend the GAF warranty however we need to follow GAF install procedures to the letter. We do that for your protection.

[@r32rtb]

Eric Styer I have been able to get the GAF TPO and WB181 from a local roofing distributer. Having to purchase full product i.e., 3 times what I will likely use. I can take some time to do the work as I have a large enough garage. The TPO is very heavy and had to cut roll down and chain hoist to get on roof. These guys look to do great work, just can’t afford someone else to do it. It is pretty amazing how much damage some of these new RVs have. My RV is a 07 and didn’t have much damage but I did replace 3 sheets of decking. I hate the EPDM junk. I am also able to get the M1 from the same dealer but buying a entire case as they don’t stock white. I also bought a Leister heat welding gun and will be practicing a lot before figuring out those curbs. The unstructured is pretty expensive per square foot also. All in will have close to $1300 in material and tooling but does take a lot of time.

[@ericstyer2890]

Roy Sprague the heat welder isn’t too bad. Your budget is about twice what mine was. I ended up with JM 45 mil structured. Nowhere near as clean and pretty as RVROOFINSTALL does them but for my 05 it will last much longer than it would have otherwise. I did the curbs and am at HD right now actually looking for longer bolts for the AC units. Will prob have to use allthread and make it work. The whole time I’m doing my project I’m wishing I had a shop to keep it out of the weather.

[@shermanv3301]

How thick of plywood should be used for the decking? 3/8?

[@RVROOFINSTALL]

Depends on the coach. Some we have used ½ inch...some ⅛ inch.

[@shermanv3301]

@@RVROOFINSTALL thank you for the answer

[@Cotton088]

Can you ballpark a 31' x 8' replacement cost at todays prices (to make it simple...with no decking replacement or other repairs). I have a Keystone Sydney edition 28FRL-S that is getting close to needing a replacement. This is a long term keeper RV for us so we want to do it right. I'd like to know how much to save is why I'm asking now for a ballpark. We are in Montgomery Alabama so it wouldn't be far for us to travel. Thanks much

[@RVROOFINSTALL]

We shy on quoting jobs on social media. our contact information [e-mail]

[@Cotton088]

@@RVROOFINSTALL done

[@sandiegojody]

If Dicor is crap, what brand caulking do you recommend?

[@RVROOFINSTALL]

Please don't take this the wrong way my friend....these videos a are not tutorials. A camper roof is not quite that easy to do. But to answer your question need use M1. It's a commercial caulk. We do not use anything RV. Dicor is the absolute cheapest products on the planet. They exploit people's lack of knowledge for their gain in sales...in my opinion. Why would you want to apply a caulk that requires you to have to constantly reapply?? Just think about that. A yearly touch up is smart....but times a year??? C'mon.... they're holding in to your wallet!

[@shermanv3301]

We us a lot of dyamonic urthane sealant on flat roof termination bars... Its the best sealant..i think

[@agentorange2554]

@@shermanv3301 I worked with Tremco Dymonic on metal roofing. It's the only product we used. You are one of the very few people to mention it and as far as my experience goes it is superior. That stuff sticks to everything, especially me!!! LOL.

[@RVROOFINSTALL]

@@shermanv3301 who are you?

[@deborahmeadows148]

What is the name of the glue you use glue down the rubber membrane

[@RVROOFINSTALL]

We do not use rubber, we use TPO and the adhesive is GAF TPO adhesive. Thanks for watching!

[@stevenfoster5737]

I have a few small issues to attend to on my trailer. I hope it's not a trade secret but would you please tell me what type of caulk you use?

[@RVROOFINSTALL]

Chemlink.com makes a few different products. You can surf there to see what will work best for your concern. We use M1, Duralink 50 and Metalink. Thanks for watching.

[@danhjelholt5262]

Where are you guys located ?

[@countrylife392]

I have got a molded fiberglass roof I believe on a 2000 for rexhall aerbus, I would like to get the whole roof redone How do I get in touch with you to get an estimate and set up an appointment

[@RVROOFINSTALL]

We did have an image at the end of the video that showed our contract information?? I'll watch to see...but anyway ..our office hrs are MF 830-4. Telephone 📞..423-475-7663. Thanks for watching!

[@leviharris4099]

Where are you guys located and would you work a 1986 jayco

[@RVROOFINSTALL]

Accidentally deleted your inquiry form. But yes we can work on your coach. Can you email us again. [e-mail]

[@kimberlysturgeon4594]

We are

[@RVROOFINSTALL]

??

[@RVROOFINSTALL]

The construction if anything is worse. Rest assured that any improvements the RV industry makes would be for the sole benefit of the RV manufacturer. All low slope and flat roofs need curbs to function water tight. So it doesn't matter if it's poured concrete, 1/2 inch solid steel, with no curbs it will leak.

[@tonymansilladerqui1104]

What filling do you use for the boots on the latter??? Thanks in advance

[@shermanv3301]

The filling is called pourable sealer.

[@myoldmill]

Where is your business to replace my roof?

[@RVROOFINSTALL]

We are a few miles south of Chattanooga TN in Fort Oglethorpe GA. 423-474-7663 ... [e-mail] Thanks for watching!

[@elevator9592]

What do you recommend for caulking? You have made it clear that dicore is junk but that is all I see around here. Thanks

[@RVROOFINSTALL]

Are you wanting to just go over Dicor or are you doing a new roof?

[@elevator9592]

@@RVROOFINSTALL I’m planning to do a complete re-roof with the 60mil TPO and the raised curbs like you folks use. So I will basically only have caulking at the trim strips. For the ladder curbs what is recommended to fill the curbs. Thanks fo taking he time to show us novices the correct way to do this.

[@RVROOFINSTALL]

@@elevator9592 this is not a DIY channel friend. RV roofs are not easy to do. A lot of detail to pay attention to. All the products you need you can find at your local commercial supply house.

[@juniorrodriguez9303]

Wheres ur company or name of business need a roof done myself

[@RVROOFINSTALL]

RV Roof Install LLC Fort Oglethorpe GA 423-474-7663 Thanks for watching!

[@agentorange2554]

@@RVROOFINSTALL Would you consider relocating to Wisconsin? LOL

[@kevinmckay810]

Hi I'm a flooring contractor and I can do all that myself, so would I be able to buy the a/c and vent risers from you? Iv welded 1000s of feet of flooring seams and installed medentek flooring 32 years , Thanks

[@RVROOFINSTALL]

No sir. We do not sell anything at all. All curbs, boots and other accessories are proprietary to us. Thanks for watching!

[@jasenyelton1736]

What do you use for your "protective strips"?

[@RVROOFINSTALL]

Protection strips are remnants of the TPO roofing. We use M1 by Chemlink behind the gutter rail. Thanks for watching!

[@indo3052]

So let me express my opinion. Ive had multiple rvs. Been around construction my whole life. Also spent 5+ yrs in water damage trade. Correct me if im wrong but, why do they fail to properly flash rv’s. When i say flash im talking about the construction of the rv itself to prevent leaks. I feel they could be flashed/constructed in a much better manner to prevent water damage. Im not expert in life, but we supposivly been to the moon and back, yet they can’t properly flash an rv so theres no possible way water can get in the corners. To flash it, construct it so it’s impossible for water to get in the crevices regardless if theres caulking or not. Ive talked to owners of rv sales businesses and yet they claim theres no roof warranty for over 6 months. Are u kidding me? I believe this is a conspiracy, Well technically i shouldnt call it a conspiracy, as they are doing it right infront of u. Why are the corners not flashed? Same way u would do to a window to a house. Or a house roof, etc These rvs are literally designed to leak. Trust me. Ive put enough thought and time ln this issue with rvs. Its so basic ( common sense) it baffles me why anybody doesn’t question it. Why are all the rvs constructed so that the face or front, underlaps the roof, and the only thing stopping the water getting into the front corners is caulking. Its beyond my comprehension. When u proper flash(a house roof, house windows, house siding, rv siding, etc) u dont have to worry about water penetration. They do this intentionally, in 10-20yrs u got water damage on all corners of ur rv. Next thing u know u got soft subfloor. Ive come to conclusion that this is intentional. As it seems very basic to prevent

[@RVROOFINSTALL]

Corporate america doesn't care. The manufacturers have a moto....Get it built, Get it out, Get it sold. So why are they not built well.... greed. All the money they save on material and labor to do proper steps and pass the problem on to the customer...greed. Thanks for watching.

[@durango8882]

These things are so poorly made. Why isn’t there mandatory inspections by an expert?

[@es2709]

Poorly made is a huge compliment considering the total lack of effort and concern from manufacturers. It should be criminal, no doubt.

[@danhjelholt5262]

Where are you guys located?

[@RVROOFINSTALL]

Fort Oglethorpe, GA..just a few miles south of Chattanooga, TN