Us rx7 guys run master cylinders and boosters from either a turbo 2 or an old 626 when doing 4 piston swaps or big brake stuff because they have a larger bore and are a direct swap.
@3drifterboy2 жыл бұрын
Bigger brakes like the mustang brakes definitely require a larger master cylinder. Larger pistons in the caliper require more fluid to move the same distance. Otherwise they will always feel spongy.
@mixxedboyybuilds82732 жыл бұрын
Turbo 2 or 626 master is bigger & a direct swap.
@paulezay35992 жыл бұрын
Dude the mazda is going to be a straight ripper
@chicagovasko2 жыл бұрын
💯
@okobojian18602 жыл бұрын
Oh ya let’s get this kid over 100 K before he goes back to Colorado. 😎
@rsharney11112 жыл бұрын
I appreciate your work ethic and detail. God rewards people like you.
@parl97312 жыл бұрын
This thing is soo clean! I'm hooked on the look of the wides all tucked under there so perfectly. Can't wait to see this thing rip again!
@diyracing30492 жыл бұрын
I ran into a very similar problem with the brakes. You need a master cylinder that moves more volume. I had to go with a strange large bore master,problem solved. There's a video on my channel explaining it also. Thanks for the good content.
@206sea2 жыл бұрын
I love the flammable bottle as a hand rest! Good touch!
@make-it-work4u2 жыл бұрын
It looks like condensation from the bov Hot air into cold aluminum will give some water until its warm. Thats my 2 cents
@lilmike17802 жыл бұрын
Soooo glad it’s your rides turn, always amazing work
@kevinmack562 жыл бұрын
Cant wait for the run back with Kyle
@louisp63842 жыл бұрын
Just appreciate the fact he takes Lucy with him on trips 🐕 keep up the good work!
@dpgarage45012 жыл бұрын
Awesome to see this getting so close! Idk about the gas pedal spacer though man, you should probably add some additional bracing.
@ackilbits2 жыл бұрын
I'm digging all these uploads you been puting out bro 🤟
@alltheboost53632 жыл бұрын
My best guess is that it's from condensation coming from the intercooler. your bov is right there especially if that was the first time you got to up in boost hard. I know there's been times where my car has been shut off during the heat of the day and then fired up first thing in the morning... let it warm up for a minute or two and then rev'ed it up and it'll blow a Mist when the law valve opens.
@tymills61702 жыл бұрын
Manual brakes for sure! Glad to see it up and running, good on ya!
@blaznmax88772 жыл бұрын
You never realize how hard u mash the throttle pedal. Until it snaps .. put some side braces on it
@jamesmcivor3402 жыл бұрын
Contents been great lately, looking forward to your (beautiful) rx7 making competitive passes
@Kevin-zo6nz2 жыл бұрын
You have mustang brakes yes make the switch, the diameter of the shaft will be much bigger, huge difference in pedal feel and response
@chicagovasko2 жыл бұрын
Definitely need brakes. 😁
@Tiny68682 жыл бұрын
Yes. Need the bigger master. The manual conversion by UPR is awesome
@EdwardAlcala2 жыл бұрын
Where’s my dawg at?
@Manvrick2 жыл бұрын
I'm excited to see this thing coming together. Manual brakes all the way.
@nick.4.2 жыл бұрын
super excited for you bro! build is beautiful came along way!
@johnnybodangus25292 жыл бұрын
Looking and sounding great! Ditch the booster it's a race car!
@BEYTEK2 жыл бұрын
Man im sooo buzzing for this!!
@fast97z242 жыл бұрын
I was today years old when I realized what the Tig in Metigulous meant. I'm kind of a dip sometimes.
@jamesmcivor3402 жыл бұрын
We all are sometimes 😁
@RaceBrosCarlos2 жыл бұрын
8 Rotor Ftw!
@chicagovasko2 жыл бұрын
💯 x8
@HenryOCarmichaelSmith2 жыл бұрын
Living life on the edge using a bottle of acetone to rest your wrist while welding haha love it
@MayhemVideosTX2 жыл бұрын
Stoked for you. Can't wait to see it at the track. Been watching since you got the car
@nocoasthero12042 жыл бұрын
I’m betting Rob Dahm isn’t that hyped on this but I am!
@imdabeast1002 жыл бұрын
I think he’d admire the craftsmanship at very least
@kevintibbetts52492 жыл бұрын
Very excited for you man, long time coming this
@cornfedwrx2 жыл бұрын
Rx7 lookin mint 💯
@stoker202 жыл бұрын
Everything is coming together like a work or Art!! Let's Goooooo!
@CraaaigV3022 жыл бұрын
Car sounds so sick tho good shit
@mountainsgarage2 жыл бұрын
Buy a 1987 Dodge Ram Van Master Cylinder, about $35 new no core. Don’t forget driveshaft containment and transmission safety shields, you have done such a nice job!
@mixxedboyybuilds82732 жыл бұрын
Turbo 2 or 626 master is a common swap, bigger, & bolts right up
@BassManBobBassCovers2 жыл бұрын
Holy crap that's a lot of fab work! Looks sick doe!
@RiptRome2 жыл бұрын
Gratz bro it’s been a long road getting close.
@twadam52182 жыл бұрын
Re: the brakes - call and talk to Willwood. Not saying you need to buy there stuff, but they were very informative with piston surface area vs. master bore size and brake pedal pivot ratio.
@MonkeyFabGarage2 жыл бұрын
I had a couple times When I got the cheap pads and the brakes just felt spongy. I had it happen on the Phoenix. I just changed the pads to a nice set of hawk pads. Much better
@turbomonza15612 жыл бұрын
Love finally seeing the car move around. I know it’s hard to stay motivated but man you do killer work maybe after I break my 8.50 cert I’ll have to trailer my car from Cali to you and get some love. Think if you had a buddy or shop partner around it be easier to stay focused and bumped love your craftsmanship and keep up the good work!!! And I hope I’m not alone I’m thinking when you get back home hang the go pro up on the wall and film what your doing with small clips of going over before and after in between what your working on. Definently need more content
@ThePeoplesLlama2 жыл бұрын
Always clean
@chucktaylor76432 жыл бұрын
Sounds good, mr2 better watch out! Can't wait for that race
@88_turbo_fox732 жыл бұрын
Good job bud like your work
@chadbanks76112 жыл бұрын
Ya Boi the quality of your work is impeccable 👌 can't wait to see you and Kyle rip up the track
@chicagovasko2 жыл бұрын
Who you got? 😁
@jamesmcivor3402 жыл бұрын
@@chicagovasko what cars
@chicagovasko2 жыл бұрын
@@jamesmcivor340 in the video dude said he wanted to see them both run I asked who he thought would win
@jasonmccoy5672 жыл бұрын
Dude your fab work is beautiful. I would hang pics of that engine bay all over my walls. That's my favorite kind of art
@davejames20152 жыл бұрын
Check booster for vaccume leaks, also make sure it's check valve is working
@MegaSpool2 жыл бұрын
Do you have a dump valve? I have a similar setup with a VS 88/103. I’ve been leaving on 15. With my dump valve closing at 10psi I can get mine up to 15 in about 4 seconds without having to pull any extra timing to get it to build boost.
@M3rVsT4H2 жыл бұрын
No point guessing about brakes.. Hydraulics is pretty much just maths. Find someone who knows how to calculate the optimal bore size for your setup and then go shopping for that.
@eaar5162 жыл бұрын
I'm doing a similar build except its in a 88 toyota supra! Going single 88mm turbo as well. Your build looks Awsome nice work man!
@okobojian18602 жыл бұрын
Ditch the rx7 brakes. And get this thing so it will stop 🛑 might be handy if it goes real fast. 🤣
@crazydog25802 жыл бұрын
id switch just makes sense
@bryduhbikeguy2 жыл бұрын
Little bit of Aerosmith leaked outta my brain with the wristbrace scene."Livin On The Edge"....Great job on the ride.Sounds mean and ready.
@20b3rotordream2 жыл бұрын
Definitely go with a manual brake setup and with the added brake size you need a bigger bore master to compensate for more line composite. Just my 2 cents.
@matthewhannon25092 жыл бұрын
my guess, and thats all it is, is you still have some air in the lines or a small leak somewhere, I dont think the mustang brakes would make that much of a difference.
@emmanuelmeris58412 жыл бұрын
Nice work H. How about a third leg out to the inner wheel arch, to triangulate the gas pedal mount? Should take the wiggle out of the mount for no extra weight really.
@joehall20922 жыл бұрын
LUV THAT SOUND 💓 CAN'T WAIT TO SEE IT FLY ON THE ROAD OR TRACK 👣HURRY
@cryptkeepervi2 жыл бұрын
Exhaust looks great like that
@derekg21322 жыл бұрын
My mustang makes a humming type noise only when I drove it though ended up being the rear end gears but sounded like yours but not at idle just driving. I thought you said florida for a month. Humming type noise can be many thing air escaping somewhere exhaust leak anything. Like I said mine was driving was rear end
@bigcaputo092 жыл бұрын
I can't wait to see you run down the track with this!! It's Super sick!! Get a bigger bore master cylinder for the brakes!!
@rj_boostedz28972 жыл бұрын
Please post a video on how you setup useing the bump as boost scramble if you can please thanks man
@realmearthheaven65762 жыл бұрын
Yea do the mustang brake stuff. I’m hype to see it rippin
@route222FAQ2 жыл бұрын
Question, are you self taught welding or did you go to a welding school? Your welds are crazy good!!!
@herbiederby33942 жыл бұрын
I'll say mustang brake set up go for it...the work is amazing 💯 % and continues but all worth it at the end... be well 🤙🙏
@Brother2Jis_27s42 жыл бұрын
Depending on what you find is wrong with the brakes, realistically if you have all mustang stuff doesn't entirely mean you have to upgrade your master too. I've seen some oddball combos work and other ones that seem like they'd be ok, aren't. See what's up with your brake issue and if you dont care to spend a few bucks on that then do it. Only if its going to fix it 🤙
@teunex2 жыл бұрын
Looks so much better with these rear rims!! with the hood it will be so sweet, maybe get some air on the front to lower it for shows ;P
@keanudeeter-combs40182 жыл бұрын
Add a support piece under petal bar. Don't want wiggle at 170mph when you have it pinned.
@brocklowe1182 жыл бұрын
Fuck Yeah!!! Been waiting
@QuickSiR2 жыл бұрын
Nice choo choo train you got there. 😋
@josephbeebe68732 жыл бұрын
Where do you get the purple a n fittings from?
@Forever_Luke2 жыл бұрын
How much cash do you charge for your k series manifold you made for kyles red mr2
@2raw7812 жыл бұрын
Sheeesh 🔥
@CraaaigV3022 жыл бұрын
Yea I'd ditch the rx7 master ND go manual mustang it's prolly to small anyway because the stock brakes r super tiny on them cars like real small
@jessehurdjr10372 жыл бұрын
U doing it u have mad it brother
@micheldiaz69122 жыл бұрын
Good job...
@potenitro87962 жыл бұрын
Check out the chase bays manual conversion kit i have it and it works great everything bolts up with nice quality parts
@nickyboi79642 жыл бұрын
I hope it goes in the dyno soon with Dr Tune em all
@dakotaharbert9352 жыл бұрын
Hell yeah!!
@FangOfTruth2 жыл бұрын
Your in Florida. It could have been condensation that got cleared out.
@coreyabraham31122 жыл бұрын
Definitely get those things swap out bigger as always going to be better And definitely find some billet
@RANDIMHAVOC20112 жыл бұрын
Match it all up bro.
@erickholm95632 жыл бұрын
Definitely make the swap to mustang booster. The car is looking great!
@jamesfacts52322 жыл бұрын
Wheres Motion Race Works @ Help Meticulous Full Send Kit
@Watchmedome30172 жыл бұрын
That turbo is so quiet when spooling up. The G series garrets sound like a dam turbo jet engine 😂
@chicagovasko2 жыл бұрын
Hayden is it true you mostly weld with your eyes shut if so all them welds made blind thats talent and smart.
@thewraith63602 жыл бұрын
Check the master cylinder bore size vs the SN95 master. More than likely the Rx7 stuff is too small of a bore.
@lastmanstanding51172 жыл бұрын
Nice!
@410connects2 жыл бұрын
Im ready for the rematch
@derx66662 жыл бұрын
HYPE
@subhumann2 жыл бұрын
I've been told that comments help with the KZbin algorithm. 😁
@bobthomas94032 жыл бұрын
Is that a stuck open injector??
@racerx20842 жыл бұрын
Sounds like a ripper
@seancreswell892 жыл бұрын
I would definitely upgrade the master cylinder
@turbomonza15612 жыл бұрын
Need more content
@peterschmidt28492 жыл бұрын
Badass 🇺🇸🍺
@paulgeorge49762 жыл бұрын
U need to make sure to bed the front brakes in so drive it for 5 minutes let them cool down then do it again if the disc are solid it takes a good 10 minutes then cool down
@zekialfreido2 жыл бұрын
I'll tell ya stock mustang front brakes are basically like having line lock
@TeamDPerformance2 жыл бұрын
Strange master cylinder set up
@BadHorsie22 жыл бұрын
Put a brace from the floor to the gas pedal bracket.
@tylerrobertst-rob17312 жыл бұрын
Go on and go manual brakes, you'll end up doing it in the future anyway. Either get a mustang master or just go on with a willwood. I got like $220 in mine works great
@biggrigg9382 жыл бұрын
remove the residual valves from the rx7 brake master in nz we run twin 4piston calipers with stock master no probs