S7-1200 "Stepping Motor" Control Tutorial

[@duynguyen8580]

em dùng S712000 DC DC RELEY thì có điều khiển được motor step không ạ

[@carlossantana5994]

can we use the code with a Tb6600 driver and the nema 17?

[@plc247automation6]

all stepping motor same

[@plant_paradox5663]

So can any output pin be used for pwm

[@plc247automation6]

go to my website sir

[@zellerpresscontrolsystems3801]

How do i save the actual position values at power off and power on? mine are 0 AFTER POWER DOWN.

[@aleisharivera6052]

What type of power supply are you using and how do you have it connected to the plc?

[@plc247automation6]

Please visit the article on my Website for detailed instructions

[@mohamedelsafty9321]

sir could i control the half motion step and full motion step using this code? and how if yes

[@spk7054]

available for absolube ?

[@veermanrob]

Nice video. What is the modelnumber of Siemens S7-1200? Can you do this with relais outputs?

[@plc247automation6]

Need DC DC DC Model sir

[@vengieviernes5617]

can i used 1214 s7 1200 ac dcdc sir

[@plc247automation6]

can sir

[@xx0martijnk0xx]

is there any way to control a stepper motor with that driver using a S7 1212C ac/dc/RLY plc?

[@ENAutomation]

you will need a instal a PTO Card

[@elrincondeish2867]

Excuse me, can you share me the programation please?

[@gonzaloandresgarcialopez677]

Hi there, why does the pulses per motor revolution is 1000? Is that from the stepper characteristics?

[@chimaeria6887]

Yes, that entirely depends on your motor and motor drive setting.

[@j-sauce2151]

Hi sir, have little problem. When i'm in the "commission" part to make it manually, i can't click on "enable" after click on activate( it still grey)

[@euclisesberreshity6167]

Está bem, depois passo aí.

[@aldinandigodinez9740]

What version of axis?

[@plc247automation6]

Ver.3.4 also ok

[@ArtemZhykharskyy]

Thank you for you video. Connected everything as you did. Motor is operational from the Technology object Commissioning page. But when I try to control it from the SW like you did, MC Move Jog block generate error ID16#8402

[@ENAutomation]

It's a velocity problem you have to incresing the velocity

[@vengieviernes5617]

hi sir can you please show the wiring diagram thank you

[@plc247automation6]

Please go to the article below the video description

[@gieviernes8005]

Hi sir what are the model number of the driver and the motor thank you

[@plc247automation6]

Leedshine DM542

[@IvánMéndez-k1h]

If I have the DM322E Driver, that Only has PUL, DIR, OPTO and ENA To what do I Connet the OPTO and ENA? probably the OPTO will go to common ground but what about the ENA?

[@mwgmlg5600]

Yow I can't access the article, it keeps told me unblock the adblock even after I completely uninstall the adblock

[@plc247automation6]

reintall your Brower

[@hubalaszlo6645]

Where are the resistors?How are they connected to the circuit?

[@plc247automation6]

Please visit the website for details

[@hassanahmed2908]

Hello sir can you send me completely process of this video.

[@hassanahmed2908]

On my Gmail

[@elrincondeish2867]

You have It??

[@gieviernes8005]

Can i use AC DC DC s7 1200

[@plc247automation6]

Can sir

[@vengieviernes5617]

why thier is a resistor sir.

[@plc247automation6]

reduce 24 to 5 vdc