Thank you again sir for clarifying this industry wide misconception, I have seen this in many electronic books, even from the University.
@sambenyaakov8 ай бұрын
Indeed, Thanks for comment.
@icesnk8 ай бұрын
Hello Professor, thank you for sharing your knowledge, wish you the best from Romania!
@sambenyaakov8 ай бұрын
Thanks
@gonzalomeabe52568 ай бұрын
Hello, professor. Thank you so much for your videos! Very well explained and very informative. Greetings from Argentina!
@sambenyaakov8 ай бұрын
Thank you for your kind note.
@electroquests8 ай бұрын
Thank you for the explanation and analysis! It has been very helpful!
@sambenyaakov8 ай бұрын
Thank you.
@cmuller14418 ай бұрын
13:21 I guess a solution is to combine a normal RC filter with small R to cut high frequencies with the RC+BJT (with higher R) to deal with lower ones (so you don't need a huge C)
@sambenyaakov8 ай бұрын
But in the 'nirmal' RC filer the current will pass via the R?
@cmuller14418 ай бұрын
@@sambenyaakov unfortunately yes. That's why you have to use a small R and can't filter low frequencies unless you have a ridiculously big capacitor. But that's OK if that tasks is done by the BJT+RC.
@Hirouche8 ай бұрын
Professor Hello ,Thanks a lot for this clarfication, God bless you .
@sambenyaakov8 ай бұрын
Thanks for warm words.
@vaks2l8 ай бұрын
Well, it is not related to filtering, but low output impedance is a fairly important aspect of any power supply and this circuit enables it due to the common-collector configuration of the BJT. Nevertheless, no doubt that there is a huge misconception about the statements given in the Cadence presentation. Suggestion to all electrical engineers - please use relevant references to learn electronics (Sedra-Smith, Gray-Meyer, etc). Thanks for a nice video lecture!
@sambenyaakov8 ай бұрын
👍🙏
@foobarables5 ай бұрын
Companies like Cadence and Altium should stay away from this kind of presentations on subjects they don't fully understand. It would be better if they would both concentrate on delivering quality software. Cadence used to be good. But not so for the latest versions they released. Altium is an other story.
@sambenyaakov5 ай бұрын
@@foobarables 👍
@cmuller14418 ай бұрын
7:21 I wonder if we could add a diode in series with Rf to increase the voltage drop.
@sambenyaakov8 ай бұрын
Thanks for your input. Indeed you can, but better to add resistance to Rf to get a lower frequency break point. On the other hand , if the current drops you may still not have a sufficient voltage drop with the Rf.
@Cydget8 ай бұрын
If i'm understanding this correctly, you only consider a miller capacitance to be a capacitor multiplier circuit( capacitor across input to output). The bjt filters merely let you design for lower currents, and thus you can make r smaller without making the capacitor larger. Essentially you can move your pole into higher frequencies without needed a larger capacitor. The misconception being this effect does not actually increase capacitance in any way.
@sambenyaakov8 ай бұрын
Thanks for your comments. There are other cap multiplier circuits that entail current amplification rather than voltage amplification (like base to emitter in BJT).
@binong73667 ай бұрын
wonderful clarification, thank you
@sambenyaakov7 ай бұрын
Thanks
@hardrocklobsterroll3958 ай бұрын
Do you have a suggestion for alternative circuits that filter that noise? I feel that it is especially important for suppressing 60hz ripple without having massive capacitors to charge
@sambenyaakov8 ай бұрын
I will try to touch on it in a forthcoming video. Thanks for your comment.
@Zetex20008 ай бұрын
Great video!! Maybe do a video about negative resistance devices and uses?😊
@sambenyaakov8 ай бұрын
Great suggestion! Will try. Thanks.
@BenjiShock8 ай бұрын
Ive used this circuit to remove a very small ripple on a 200V DC Supply. I needed to have a very clean output voltage and the load was minimal because it was for a supply for a sensor. What would you recommend instead in this case? I have to say it was a really good solution because it was easy, small and power used was minimal because of low current.
@sambenyaakov8 ай бұрын
Thanks for sharing.
@jacksmith-se8lo8 ай бұрын
Thank you for the great informations can you please makes a lecture about capacitor control circuit with dual mosfet for resonance maintaining circuits
@sambenyaakov8 ай бұрын
Will try
@vicentematricardi35968 ай бұрын
Gracias !!!!❤
@sambenyaakov8 ай бұрын
👍🙏
@thephantompsychic8 ай бұрын
Thanks Professor!
@sambenyaakov8 ай бұрын
Thanks
@tamaseduard51458 ай бұрын
👍🙏❤️
@sambenyaakov8 ай бұрын
😊👍🙏
@k7iq8 ай бұрын
Awesome !
@sambenyaakov8 ай бұрын
👍🙏
@k7iq8 ай бұрын
@@sambenyaakov I hope you and your family is safe over there ! Thinking of you
@sambenyaakov8 ай бұрын
@@k7iq thnks. Thanks for concern. We are personally OK but under a lot of tension. Hoping for a resolution soon
@k7iq8 ай бұрын
@@sambenyaakov Glad you are OK. It has to be hard. Things will be fine, I'm sure.
@ЁбрагимИпатенкоибнАдхарма8 ай бұрын
Very interesting, thank You! and some bla-bla-bla in order to make this content rated as it should
@sambenyaakov8 ай бұрын
Some content is missing?
@ЁбрагимИпатенкоибнАдхарма8 ай бұрын
@@sambenyaakov Why? I meant adding some extra words for youtube algorithms to advance this