Samsung Dryer Moisture Sensor Replacement

[@jasonkristek5643]

I watched several of these videos and couldn't find how you determine which sensor bar is bad. I was about to change both when I noticed there was quite a bit of lint where the wires connect to sensor bars. I cleaned that out and tried dryer without replacing either bar. Worked like a charm. Guess it wasn't getting a good connection. Might try that before buying unnecessary parts, just saying. I appreciate these videos though. I was apprehensive trying this on my own but the clear instructions gave me confidence to try. Thanks!

[@scottrywolt2752]

Thank you Jason! Cleaned the connections and the lint that built up in the filter housing. All fixed! Also, thank you Repair Clinic.

[@reedog117]

Those bars are only $5-6 a piece

[@amybutler1851]

I would just replace all of them

[@SpeedDeamon95]

These are just metal bars right? Surely they shouldn't go bad that quick.

[@emiliotristan6760]

My Samsung dryer (model DX50F9A8E) would turn on but then would stop and after a few minutes would start again....to the gentleman that provided the information about cleaning the 2 metal sensors before taking the housing filter apart...THANK YOU! (I lost the thread to reply with this comment). But thats exactly what I did, I cleaned the metal sensors with a dish wash sponge (rough side) and that did the trick. Over time, the fabric softener sheets do cover the sensors with that grime or oily substance.

[@hinawillownyou]

This was simple and extremely useful. It helped me understand where the moisture sensor was and how a stuck dryer wipe’s was the culprit in causing my dryer to stop too early. Thank you!

[@agustinescobar9711]

It's literally a stuck sheet lol my wife was already looking into a new set 😅 not today 🫡

[@ipodmagic]

This video may apply to most Samsung front loading dryers. However, for models in the DV520 family, there is an extra screw holding the filter housing that is located to the front of the unit. In order to remove the housing, the unit's front panel must be removed. Please refer to any video showing the removal of the front panel first before, then attempt to remove the 3 screws securing the filter housing from inside the unit. I will give it another try tomorrow after work and edit this comment accordingly, if needed.

[@martincarlton7298]

Thanks. I already broke the filter housing trying to get it out.

[@edwardbillman3235]

Me too brother! Can't even find the F%&kn' thing!

[@1976outsider]

video shows him separating the housing, leaving the front half that has the hidden screw. i chose to drill an access hole in the front panel the 2nd time i had to do this!!

[@michaelstrange2285]

@@1976outsider p]ppq

[@petrabrown3681]

You took down the video 😩

[@jakesarms8996]

Remove those sensor bars and clean BEHIND them. Mine had lint packed behind them. Some Samsung models have only one screw and a pinch tab to remove them. No need for replacement- There's no moving parts - nothing to burn out .

[@bloodocean14]

Would it be possible to fix the connectors to the sensors? One of mine broke trying to take it off

[@catalinalb1722]

Hello I did measure 8.5v between the two sensor bars with the dryer plugged in and on. Is this value good or bad? It's a Samsung dryer and the problem is that is that dose not finish the cycle. And the clothes are wet. I did open the unit cleaned and check the heater check the thermoswitches and the sensors nothing wrong there. Don't know what the problem is. The bearing in the back needs replacement but first I would like to see that is running. Model number SDC3D702 Samsung

[@icerduzit626]

I have a Samsung dryer and i unplugged the machine, took off 3 bolts from the housing unit and cant seem to take off the housing it wants to come off but gets caught wit its plastic trim any help. I can see the sensor and looks exactly the same as your video. Please reply really need your help thanks.

[@jacobstevens7848]

Did you ever figure this out? I’m having the same issue and don’t want to break their plastic

[@jamesmachalik9924]

The newer models have a screw hidden under the front housing. You have to remove the entire front panel in order to get to it.

[@mathewfildes2739]

On some of these Samsung's you have to take the whole front off the dryer to reach a screw to take filter housing out. Found out hard way.

[@nocentz4656]

Ahhh that's what's happening eh wish they'd say models can be different 😊

[@Manny-pf1oi]

Do you have video for changing the sensor of DV456, DV422 or DV400?

[@elenmerikostudio2898]

hello, please help me determine the model of the dryer

[@Rose-xw6to]

Very helpful 👌 Thanks!!

[@repairclinic]

You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!

[@gracilism]

Unfortunately newer Samsungs do not remove like this any longer. It seems like the front panel will have to be removed to access some of the screws.

[@repairclinic]

+gracilism Thank you for sharing.

[@bpchristensen]

Actually you can remove the lint sensor unit as a separate piece with a single screw on my Samsung front-loader (its a 2009 model DV219AGW)

[@Ahennem]

I was having a problem with my dryer ending the cycle after 5 min or so. Turns out there was just an old dryer sheet stuck to the sensors and would cause it to end the cycle. Removed the sheet and it works again lol.

[@chuckstoeckel8694]

The screws keep spinning but won't unscrew. Any tips? I have a Sasung DV45H6300 dryer

[@PermacultureLongboarder]

Im sure you figured that out already but when that happens i wedge a flat head screwdriver behind the item being unscrewed to apply pressure. Use handpwer to do this. You may need yo go a thread size up after or possibly locktight.

[@thomasmcneill18]

Do I really need the sensors connected! Because my clothes don’t dry like it supposed to

[@adamr3028]

so despite what setting it's on,is this the reason why my samsung dryer spins for only a few mins then stops every single time?

[@maribeavers4597]

My dryer is heating and turning but doesn't seem to take the moisture out so the clothes never fully dry

[@viperfukgoogplus386]

Sounds like your dryer exhaust is clogged

[@marcogioffre6106]

my dryer shuts off before load is dry, help!

[@viperfukgoogplus386]

Use the timer.

[@nphil2014]

We

[@Keonahawk24]

Having the same issue

[@Keonahawk24]

I hate this dryer

[@lestergiron5555]

My does exactly the same I set the timer for about 30 minutes and after a few minutes stop no matter what cycle I used!!! Any body has an idea what is the problem with the machine,or what sensor should replaced?

[@bobcazz9808]

What model # ru working on I need video on Samsung dryer Dv45H 7000

[@chamberscountyoutdoorexpoo9918]

How do you determine the moister sensor is the issue? My dryer model no DV52J8700EP will start but will not dry. The belt does not engage the barrel and the heater will not kick on. Samsung Support says most likely a sensor, but would not specify which sensor without a repair man looking at it.

[@alfonsosmith1538]

I have the same model but my dryer stops after exactly 2mins into any of the cycles im stuck because of all of the possible problems but no way to troubleshoot or pin point without replacing parts until you replace the right one. im stuck

[@Texasmadepyro8006]

So now do you when to replace?? Because whenever I press start it won’t go like it klicks and says sensor

[@lbrown3306]

Hi I was wondering if this could cause the dryer not to heat at all on any cycles

[@repairclinic]

+L Brown This part really can't stop heating of the dryer, no.

[@DeeOne88]

@@repairclinic what is the purpose of changing this part?

[@JoseGarcia-hz6xk]

1-MY wife complained of Dryer not ending dry cycle in auto mode 2-Looked around and followed this video procedure to replace sensors 3- However failing, had her show me issue on actual machine 4- Turns out she had the "Wrinkle Prevent" button depressed extending cycle 90 minutes 5- Turned Wrinkle Prevent Button off, now all is ok (I'am sure they are just metal plates, unlikely to fail as they are just conductors )

[@repairclinic]

+Jose Garcia The sensor bars can get damaged if people dry an item like shoes.

[@SK-wp6vh]

Had a same problem and thought about replacing sensor, seeing your post and saw Wrinkle Pevent Button was indeed pressed "ON" lol, thanks Jose!

[@JCJaselyn]

How to make your Samsung front load dryer not be in cooling mode

[@Jason-82]

I have model# DV42h5200EW/A3 mine doesn't come out this way, I've tried to pull on this thing for an hour and it still won't come out. any tips on how to get it out or what I'm doing wrong?

[@paulmeacham3336]

Yeah you’re gonna have to get the front panel off on your dryer. There was some hidden screws that you can only get to when you take the front panel off of your dryer. Then you’ll be able to get to the lint catcher

[@Sasquash85]

I took out the moisture sensor and cleaned the whole thing inside and out installed it back & still having the same problem. What should I do next? …………. Can I just unplug the moisture sensor and will it still work?

[@Sasquash85]

It’s giving me a error code t0 dryer starts but does a count down goes for a couple minutes from 55mins to 1min then turns off like it’s dry then gives me a error code

[@enriquemerizalde8140]

Show me how to erase error codes dryer general electric

[@Phillygoon79]

I have replaced every component. Thermostat/thermister/heater element/ thermostat coupler. Everything but the sensor bars. PLEASE PLEASE HELP!!! Before I waste money buying a sensor. What am I missing

[@REGGIELOVELOVE]

My dryer turns on but when I hit 'start' nothing happens. I do hear a faint 'click' but it doesn't start. There is an icon that appears to indicate the trap needs to be cleaned. But I have cleaned it as far as I can see. Are these two things related?

[@REGGIELOVELOVE]

@Ruben Portillo Hello, no I wasn't. I tried cleaning the trap several times and changed the tubing on the back and the opening where it connects. Nothing worked. We got a used one on Kijiji. Sorry mate ☹️

[@1971zman]

check to see if drum belt broke , takev top off and see.

[@BobbyJohnson-q5w]

Hey all my lights are on and dryer not moving

[@dj9281]

Got the screws out but the plastic housing will not budge. Tried a flathead to pry it away but it started snapping pieces of plastic off. How to dislodge the plastic housing without breaking it? (mine won't come out the way shown in video)

[@stevehorvath8860]

You have to take the front panel off. Check the videos on how to. Not that hard to do. Get a plastic putty spreader from the hardware store or Horrid Freight to pop the lid.

[@travisstanley5108]

Could this sensor cause dryer to not stop running? Mine continues to run after time is up heat stops but continues to tumble, and numbers on digital display get all jumbled.

[@DannyH77]

how did you fix this problem?

[@DannyH77]

was it the relay?

[@PermacultureLongboarder]

Wow that sucks i guess a control board. Id fix asap or ditch that could be a massive fire hazard

[@Drewr1976]

So what kind of Herculean strength do you need to get the sensor wires off! These damn things are welded on it feels like!

[@LosDjango007]

Can you bypass the sensor bar??

[@shanesokoluk8736]

Yes, just put it on time dry or quick dry.

[@RyanTruongChannel]

@@shanesokoluk8736 Thank you!

[@huguinmadrid]

How do I know what model my dryer is? Also where can i buy parts?

[@Amanda-pp3sd]

I broke the wire now what do I do

[@shanesokoluk8736]

The sensors are active during the Normal, Heavy duty, Perm press, Delicates and Sanitize cycles.

[@DRONefuntoo]

What modes don’t use moisture sensors

[@therealdeadpen]

samsung dryer dv395etpasu/a1 was drying everything but towels (on any setting) but now nothing dries. The air is cold so wouldn't that be the heating element over the thermistor? The screen shows drying cycle. Drying with this thing has always been weird from day one. Sensor drying never seemed to work but this video might show that problem. The only problem now is drying everything on any cycle.

[@repairclinic]

+therealdeadpen www.repairclinic.com/vwo8/RepairHelp/How-To-Fix-A-Dryer/8-160-1143302-/Samsung-Dryer-doesn-t-heat-DV395ETPARA

[@therealdeadpen]

Thanks, I found a disassemble video and just ohm everything. Found the heater coil has nothing going through it. One on order.

[@drryljoh10]

Do you replace both dryer sensors?

[@scuzzyhoulihan9853]

Mine is really difficult to reinsert T_T

[@s7a2g65]

The example guy had to lay on the top of the dryer to do this. THANK YOU! That made me laugh!

[@HandyDan]

Time stamp please, I watched this twice and never saw that.

[@JoshuaCeres81]

Do I even need the sensors? Can I just jump the sensors?

[@pettyfog1463]

Do you people actually READ OTHER COMMENTS before posting? Ridiculous... Does it work on time dry? If not, it is the heater, not sensors. If doesnt start at all, not the sensors! Geesh!

[@veronicablack3976]

LOL 🤣

[@derekconcepcion]

My samsung front load dryer it doesnt stop spinning now,it only stop of course if i unplug it....can anyone tell me how to fix that problem? thanks

[@DannyH77]

i have the same problem!! did you fix yours?

[@tompekar1133]

Critical, tie a string to the two wires. If you don’t the two wires will disappear into the body of the Maytag dryer and take six hours to retrieve.

[@mushbert]

If you do this I suggest wearing gloves, as there were sharp metal burrs all along the edges of the metal strips in my dryer. The strips were clogged with bits of lint, but also many threads from towel fringes, I have to wonder if any of the mystery holes in my clothes were caused by them catching behind them. After cleaning I filed them smooth.

[@repairclinic]

+mushbert Thank you for the helpful tip.

[@mushbert]

After running the dryer again with a load of towels, I can confirm that the moisture sensor worked far better. Unfortunately removing the metal strips can easily bend them out of shape, which makes them catch on fabric even more. Rather than replace them I filled in the start of the gaps with Bondic, seems to work well. Not sure how long it will last, but it's supposed to be stable up to 65C; at high heat my dryer reaches about 50C.

[@pettyfog1463]

Or you could just try bending them back into shape. Center of bar just touching first before ends.

[@YamahaC7SRG]

On my model no. DV328AEW/XAA (model no. is found inside door or on back of dryer) you do NOT need to remove the large, gray plastic housing shown here. Rather, the moisture sensor bars are held in a smaller plastic housing with ONE SCREW in the bottom of the larger gray plastic housing. Look inside carefully with a flashlight BEFORE removing the screws shown in this video. On my model, simply remove that 1 screw in the smaller housing and withdraw the small, gray, plastic housing a bit to disconnect the electrical leads to the sensor bars. The sensor bars and housing then come out as a small unit. You can then take the small unit to a work area and remove the sensor bars and clean them and the small housing. Lint gets trapped all around the bars; that may be the only problem.

[@mushbert]

+YamahaC7SRG The DV337AEG also has this separate module. When I removed it it seemed to be wedged in place, and it took more force than I like to extract it... To get it back in I had to take off the filter assembly as well - it felt like the wire leads were butting against something.

[@eptx888]

I have this model. Thanks for the information.

[@chevyguydiegod5516]

Water got in my dryer from the outside vent,and now it runs, for 2 minutes and it shuts off,should I change those 2 sensor s..???

[@paultrong7596]

Mine does that. But a code to comes up and I cleaned all lint. Did you solve your problems and how?

[@obey-yah]

Beware, sometimes there is a screw that you won't be able to reach until you take off the door

[@lionelwhiskerknot]

I'd like to just permanently disable that stupid sensor. Why isn't there a button to disable it?

[@jennifersmith7989]

Hi I watched how to remove the lint trap from the dryer and did everything the man did in the video yet it won't come out. Maybe I'm not prying enough but it is only plastic and I don't want to have to replace it. I am just trying to clean the excess lint and Lord knows what else that is all built up down there...you can see it but not get it out due to the small space...anyone have any ideas that might help? Thanks

[@five-minutegenealogy1119]

Agree: this video is lacking a description of all the little clips holding in the filter panel. I ended up cracking mine and couldn't get it out after over an hour of wrestling with it.

[@lestergiron5555]

What was the reason to replace the moisture sensor?

[@martincarlton7298]

You should let people know from the beginning that not all machines are similar. I just broke the filter housing trying to get it out. Turns out you have to remove the entire front panel on my Samsung to get the filter housing out. Pissed!

[@tsquad27]

thank you!!!!

[@katievang6169]

my dryer stays on cooling mode and not heating. Is this what is caused it.?

[@repairclinic]

Katie Vang There are a few possible causes. Enter your dryer's model number in our website's repair help section for model-specific troubleshooting and repair help: www.repairclinic.com/repairhelp?TLSID=1773.

[@paulrivas3607]

RepairClinic.com

[@charlesedwards1163]

@@repairclinic I replaced my heating element and the dryer worked for one cycle , but now will not heat up . Any suggestions

[@nocentz4656]

... why can't I pull my bar out?

[@jenniferflandreau1673]

Can u just cut the damn wires?

[@thomasmcneill18]

Do I really need those sensors? My clothes don’t dry good?

[@pettyfog1463]

Try timed dry. Maybe read up on how dryers work. Vent must not be clogged.

[@PermacultureLongboarder]

Its not always a clogged vent. It could be a failing heating element. I used to replace those a ton and it would make an old dryer new. Often times they were rusty and covered.

[@PermacultureLongboarder]

Same with hot water heater beofre throwing it out check the elements

[@PermacultureLongboarder]

And on top of that i dont want the moisture sensors either on mine. Its one more thing to break. It be nice to have that option turn off at the least especially if your control board happens to be misreading the sensor.

[@houseofsgp]

good luck taking the plastic piece off