Samsung Top Load Washer - Not Spinning or Stuck on Sense MODE, (FIX)

Samsung Washer not Finishing cycle- Getting Stuck in Sense MODE
The Fix was the Motor Position Sensor. Which detects the Speed of the tub while spinning.
Parts for Repair-👇👇👇
Clutch Assembly with TMR sensor- encompass.com/item/10240370/S...
Subscribe to the Channel for more Appliance Repairs and Tips.
If you have further questions leave a comment. Thanks for Watching.

[@hanzischultz9284]

I have the same model washer. I found one (green) of the three TMR sensor wires was severed. I think it is a design issue. The wires are too thin and it is so easy to be broken with that level of shaking when it's spinning. While I was fixing it I collected some data for testing the three components: Capacitor, Shift actuator, and TMR sensor. Hope it is helpful to those who need it. 1. Run capacitor (1). Capacitance = 45 µF ±5% (2). Check body shape. 2. Shift actuator (1).Ohm range: 1000-1100 Ω. (2) check wire. 3. TMR (tunnel magentoresistance) sensor. There are three wires: green, blue, and red. Using Ohm meter to measure, one should get these: (a) Green-Blue = OL (b) Green-Red = OL (c) Blue-Red = 10 KΩ

[@JesseApplianceRepair]

thanks for the info 👌 im pretty sure someone will benefit from it

[@6point2000]

@@JesseApplianceRepair Do you have a link to order the TMR ? . i am look and no luck where i can buy it .

[@JesseApplianceRepair]

@@6point2000 Samsung doesnt sell the sensor by itself unfortunately. but you can find the link in the description to the full clutch assembly. that includes the sensor. but I recommend to check all wires for any rips before you order any parts.

[@capslu6305]

Where can I buy The TMR Sensor

[@alextorres1544]

Yes, please keep posting more appliance repair videos! Thanks!

[@georgeharvard1417]

I just want to say thank you to KZbin. And I want to thank you to demand that's doing the work on what he's showing right now. It helps a lot of people just for what you're doing. Thank you so much you help a lot of people thank you

[@JesseApplianceRepair]

Love helping others. Same as when I first started and others helped me. Thanks for watching Cheers

[@JohnMEstrada]

It's so hard to find any videos for this specific Samsung washer. Thanks for making this. I am going to try and clean that sensor tonight and see if it helps. Much appreciated!

[@electron7373]

Top work! Thank you for the repair guide!

[@sellomahlo9034]

Thank you very much for an informative demonstration on how to deal with the sensor in question - well done and keep it up. I am the new subscriber to your programme and intent to be a regular.

[@JesseApplianceRepair]

Thank you so much for the Support, it means alot. I have more content coming out.

[@jerrydonofrio4154]

Superb instructional with easy to understand explanations and video great as well a audio. I know understand how this newer type machine works.

[@Jorge-gn7ft]

thank you so much , i just got mine up and running again thank to your video you saved me hundred's of dollars .

[@Ruben-oh4mj]

Dude....love the video and explanation. Thanks so much and great job.

[@Cbmacdaddy]

Great video, thanks!

[@javieracosta7860]

Good morning technical friend, I have a similar fault in a WA19J3000AW model in the diagnosis the hot led is the one that flashes, I appreciate your collaboration to correct this fault. Greetings from Venezuela

[@curtycox689]

Thanks *TEACH. YOUR A EXCELLENT TEACHER.

[@christianbattey3186]

Thanks for showing us how to fix the problem 👌🏾

[@JesseApplianceRepair]

anytime.. Im glad the video helped you out.

[@swishcamp81]

I Thanx for videos! I was wondering where you got your training because i want to learn Appliance Repairing!

[@moezbhaloo1681]

Thanks got lots of info. Am going yo check a top load samsung not spinning. So will check what you showed

[@danjones2110]

Any suggestions for a Samsung top load model wa56h9000ap/a2 that won't spin in normal mode. In service and quick spin modes it spins up to high rpm. In service mode are we bypassing all the sensors? No error codes are displayed. Thanks

[@royabreu3627]

Hi my friend i liked your video, very well explanatory, thx for your help

[@mikehikalea2323]

Great video and excellent teaching for a beginner like myself..👍

[@JesseApplianceRepair]

Thank you. More videos coming soon

[@wilfrednorwood2250]

Exactly what I needed thank you.

[@robertrumsby8499]

Thank you so much for the video, does anyone have the part number for just the nylon tmr sensor. Thank you

[@debracavalieri4871]

Great video!

[@stso9daa]

Jesus, you are great! i have been looking for this. it is exa t issues i have. Thank You so much!!!!!!

[@JesseApplianceRepair]

Awesome. Im glad the video helped. 👌👍

[@jaimetorres4567]

Ya cambie el sensor y no centrifuga que más puede ser

[@arnellgayo3021]

Nice.. I'll try these tutorial.

[@ashleythaeunisen8860]

Thanks for the video I will definitely try out this way on this video thank

[@jaimetorres4567]

Excelente sube más tutoriales de refrigeracion en especial samsumg

[@janettham9055]

Jesus. Awesome video man. Spot on. Well explained and well shot

[@noelcaudilla4877]

Good job,thanks

[@davenportchurchofgodbyfait8643]

very good instructions for troubleshooting. It analyzed my problem, thank you.

[@apolinarrendon7506]

Where can i get the first senscor , could you tell me the place you got it from? Thank you also your video helped me a lot

[@tdilla3818]

Question I have the same washer.is it natural for the washer to make clacking sound for a minute going from wash to rinse or like when its changing gears or something....

[@karlahernandezvalles]

Great video! It is exactly what my Samsung washer has. Do you have any video on how to rewired the sensor? It’s almost impossible to get it here in Mexico 😢

[@hernmarr]

Awesome!!! Muy bien!

[@JesseApplianceRepair]

gracias

[@dannyryan5549]

Very helpful. Well done..

[@JesseApplianceRepair]

Glad it was helped.

[@gregorystevenson2957]

Hello, great video. I have a newer model of this washer where I have encountered an agitator/spinning issue. It is not spinning. The washer was loaded with too many bath mats which when wet was heavy, and I am assuming unbalanced. The machine then stopped. After taking everything out and trying to spin the agitator and barrel with my hand, I could hear a light grinding/scraping sound underneath. Could something have come loose in the motor to the barrel/ agitator because of a heavy unbalanced load? Thank you.

[@mydogs4657]

Bearings problem

[@raulcoronado4292]

Greetings, Jesus, I think I have a similar washing machine with a model (wa45n3050aw/a4). My question is the following: When the spinning cycle is almost over, the washing machine begins to move very abruptly to the point of stopping automatically and starting the washing cycle again, filling water the tub from the beginning I already did some of the steps you recommend in this video like cleaning the tps sensor and leveling the washer on a flat place I really don't know what else I can do or if you have had a case similar to this before? what do you recommmend me to do

[@navedsyed9354]

Having the same problem when pressings to start during washing and also tried to do also rinse and Spin and found the same condition as you mention above. I should clean the sensor or replace the actuator?

[@kimraley1050]

Hi Jesus, I’m hoping you can help me. I need to replace the harness that attaches the TMR sensor to my Samsung WA40J3000AW/AA and I can’t find it anywhere. It looks just like the one in your video

[@b.aroyalty3071]

I have the same washer but it spins but sounds rough when it spins. I did the nickel glue quick fix for the handle. what part do I need to replace and where can I order it from

[@michaelstinger6785]

hi there i have the same model as of right now it has a hot & cold error it does not agitate or spin i cleaned the tmr sensor nothing what would you think thank you

[@commieslayer8218]

Great instructions, I got Samsung top load WA45M7050AW/A4 4 years old and the water pump rubber toilet flapper like check valve is separated from the rubber bushing holding on the orifice. Those who gave me the washer told me that it wasn't spinning at times and I suspect that the flapper just got wedged and blocked the port at least partially so too much of water was perhaps sitting in the basket and sensor didn't allowed to spin it. No code is displayed and if there was one, they didn't record it so I don't know. When the pump runs, I can hear the flapper ticking/knocking so I am looking for that part and it maybe an issues to find it. When it spins, I don't see and hear water shooting into the basket like on other washers helping to flush out debris and detergents, maybe not included option of this model, manual has no mentioning about it.

[@reneperez8810]

Gracias me sirvió mucho este video😀😀😀😀

[@JesseApplianceRepair]

Gracias bro. Voy hacer más contenido pronto

[@reneperez8810]

@@JesseApplianceRepair esta bueno brother👊 .

[@octaviobanuelos6812]

Good afternoon do you know the part number or do you have to buy the hole clutch assembly

[@504ksh]

Just subscribed. Keep em coming. 💯

[@JesseApplianceRepair]

Got more coming. 💪

[@504ksh]

@@JesseApplianceRepair could be so kind to do a diagnosis on top load spin issues? Song mid cycle or repeating cycle 🚲 🤔

[@JesseApplianceRepair]

@@504ksh what brand is the washer. Tell me as much info as you can and i can help you diagnose it. What is it doing. What cycles have you tried etc.

[@504ksh]

@@JesseApplianceRepair purpose of switch, and like a stator motor. How to cancel 1 or the other out? I'm a student

[@JesseApplianceRepair]

@@504ksh so the stator is a Magnentic motor. The machine has a regular motor or a stator to operate. both have a sensor where it detects the position and speed of the tub. clutch changes gears from agitation to spin mode.

[@user-gb7ev7ok7c]

Hi my friend I want to thank you for the good video and also just wondering if you have a link where to find that specific sensor I’ve been searching but not luck… can you help me with that

[@jasonkruschke2147]

Thank you very much for this. I cleaned the sensor and things are working again. Fingers crossed it keeps on keeping’ on.

[@JesseApplianceRepair]

Thats awesome. Im im glad the video helped 🤝💪

[@TerriBovitzPollard-qm9ej]

So it's my sensor or my capacitor. Those are my two choices on a code of small which is telling me my water hose or pump might be clogged or frozen water which is not the case cuz I'm living in Florida unless you disagree but your video has been very helpful. Thank you so much my brother

[@JesseApplianceRepair]

Check the filter to make sure there is no dirt on the connections of your hoses

[@sbb526]

Is there anywhere to get just the sensor, no need to replace the entire clutch assembly is there?

[@brendapryor8713]

hi i was wondering if you could help us out we have this same washer and it wont spin or drain..and it codes hot.warm..thankyou !

[@kevinbarrett2855]

Ty so much

[@leecarnes8923]

My washer will not enter diagnostic mode. It doesn't spin, doesn't fill with water, does lock lid. It just makes a weird clicking sound. Any ideas?

[@jeffmejia2978]

Mine does the same thing. Did you ever figure out what was wrong with it? Mine just started doing this after two loads this past weekend.

[@COVID-xr5mj]

​@@jeffmejia2978any solutions?

[@eugenemoreno4797]

I have the same washer, it does no spin but does make a grinding noise everything else does work properly. My sensor had a lot of grease on it so I cleaned it put it back but it did not correct it. My main worry though is the grinding noise it makes. It l lasts about 2 or three seconds stops then does it again and again. What should I be looking for?

[@antonetterobinson5476]

Thank you for the video. Can you give where the part can be purchased?

[@ELBENDC2]

Super instructivo tu vídeo

[@braedonballard6637]

Hello, I have this model washer. It will only work on rinse and spin, will run through the whole cycle. None of the wash cycles will work, it adds a little water then starts flashing with a buzzing sound. Could this be a sensor issue also? Thank you!

[@stevenfroeschl7056]

Hello, this model washer do you know why the load size jumps to extra large? Could it be this sensor? Thank You

[@666Yumaaz]

what # part is the sensor you changed? thanks for sharing

[@piggy1606]

Would you have an idea for a similar model washing machine, not entering final spin cycle. The drain pump keeps running drum won't enter spin. Tried cleaning out the drain pump and all of the hoses. Did not reconcile problem. Any suggestions would be greatly appreciated!

[@JesseApplianceRepair]

make sure the machine is not going off balance, that will restart the spin cycle. if that's ok and you already checked the water pump. then check the water level switch. most of the time is round with a clear whose. that's usually located near the brain. i will undo the whose and blow sometimes you will hear bubbles inside the tub. that's just to remove any debris that might got stuck while a cycle. if the machine thinks there's still water the pump will run constant and wont go into final spin. also see if your machine has a HALL sensor. that also affects going to final spin. it detects the speed and rotation of the motor. let me know

[@piggy1606]

@@JesseApplianceRepair will give that a try a let you know.... thanks for the info!

[@franknilson180]

I also experienced malfunctions where the machine did not get filled quickly or at all, or that it would not complete the spinning cycle with about eight minutes on the clock remaining. The solutions were easy. The first problem was easy to sort out. I loosened the water inlet hose at the back of the machine and removed the sieve on the inside of the pipe at the inlet point. After I cleaned the sieve and installed it again, the problem of filling was gone. The second problem was just as easy. At the outlet, there is also a filter which can be cleaned. I have found some thin string that wound up and caused the water pump to stop functioning which caused the machine to stop. I just removed the string and the machine runs 100% and I did not have to buy a new water pump, motherboard or electrical spares. Needless to say, I saved plenty of money and did not enrich the scammers who would take your money without blinking twice.

[@jasonweaver1252]

Hey man I have the same washer and during use started smelling and just kinda quite running so I done a diagnostic and the hot flashes any idea what my problem might be? Any info would be greatly appreciated

[@JesseApplianceRepair]

tell me more info and i can try to diagnose it.. as soon as you hit start on a rinse and spin cycle what does it do ?

[@billy7052]

Hey man - my Hot and Cold lights are flashing in diagnostics mode. What do you recommend? The cycle gets stuck during “Spin”. So I have to restart the Rinse and Spin cycle but still leaves my clothes drenched.

[@adamchristopher393]

Mine stuck during spin too. Trying to troubleshoot. Did you resolve it or I.d. which part has failed

[@ambyre09]

I have the same washer and I am trying to find that position sensor but I can’t find it. Any clue where to get it?

[@user-rk2ol1ob7m]

Hi! I have the same problem. Did it fill with the water 💦 or no?

[@pedrorosado9534]

Loved ur vid. Hope I can fix my spin on same samsung washer. You think you can send the links for : sensor, capacitor and actuator. Gonna start w/ the sensor n 🙏

[@JesseApplianceRepair]

In the description I have the link to the TMR sensor and clutch assembly. What is your machine doing. ?

[@pedrorosado9534]

@Jesus Montoya it makes sound like its about to start spin, makes bad noise for a few seconds, then stops and starts wash again. Already changed the susoension rods.

[@pedrorosado9534]

I see the link but it is for the whole clutch assembly it is too much money,,, Can't I just buy a sensor?

[@altie40]

I have been trying to locate that tmr sensor. Can you help me out, please? Thanks. Al.

[@augustharlacher5660]

I have the same model, and the same problem. It doesn't complete the cycle, switch to rinse and spin and it tries to start but stops on spin. And when it does finally start to spin it doesn't spin that fast and the cloths are still very damp. So, I'll have to look at it again more closely because I just checked the drain hoses they were not clogged. Jesus thanks for a step-by-step explanation. You are the man Bro.

[@smiley10261]

Did it work I am having the same problem.

[@raymondblakley3731]

@@smiley10261bad sensor problem If your does not spin out

[@misterdrummings]

@@raymondblakley3731 This sounds like the same problem I'm having. The machine gets hung up in spin cycle, and the cycle doesn't complete. The hot and warm LED's are flashing in diagnostic mode, which the manual tells me means either the machine or load is out of balance, but I checked it out and that is not the problem. Do you think I need to replace the sensor?

[@raymondblakley3731]

@@misterdrummingswhat the brand if it a Samsung washer top load and you replaced all four shocks then you will need a new spin basket assembly

[@JuanHernandez-eg2qg]

Hermano gracias i have one similar but my do a grainy noise while spinning I change the clutch but I can’t find the problem do you know what can be the problem?

[@user-nh9ji3mr1v]

Iam from México in have a silimar washer but this one is invertert system but it has the same problem doesnt spinmy question is it had the same sensor?

[@quickfixappliance]

First of all, thank you for this detailed video buddy. I have a question and I hope you can answer me. My samsung washer, exactly like the one in this video, after first wash it starts draining for only 2-3 sec and then stops. I know its not pump because It drains on spin easy. I checked wires and everything is good. This is the second samsung washer thats been doing the same thing. So it adds water, agitates, then when its time to do first drain and go rinse after it, it drains only couple of seconds and machine stops completely. I changed actuator and control board. Please help if you can. Keep up the good work

[@JesseApplianceRepair]

So ive had a similar issue in the past to what you mentioned. and it was the cables coming from the Computer board to the Pump that were bad. So you mentioned on the other cycle the pump drains. so that seems to be good. so get a multimeter and run the washer when its time to drain check the ports coming from the board to the pump ( the two cable connectors. ) most of those pumps should be 115 volts. Make sure you are getting the full 115-120 volts. If you are getting less the cable is the issue. Let me Know what you find.

[@HandyTim]

I can't find the sensor online do you have a link for it?

[@derekp77]

Can you tell me the part number for the nylon sensor you are replacing in the video..? Many thanks

[@cavemanproductions2.015]

That's what I want to know!

[@peterchand9804]

Thanks for explaining about the sensor on DC68-03172B-03. What is the part number or name of it and where can I get it? Or then what does that repair cost?

[@JesseApplianceRepair]

sorry for the delay. the sensor comes with the whole clutch assembly. ive called Samsung but they dont sell that part by itself. Dont know why.

[@riaanlloyd930]

Hi Jesus, I have a problem with a Samsung wobble top loader WA13F that will not spin. I have replaced the drain pump and main pc board as the drain motor does not get power to engage the gearbox to spin. Please advise what could be the problem. Thank you ,Riaan.

[@JeannetteMarie956]

How can I replace the clear pipe from the back of the washer I have a hole on it but the clear pipe but dk how to replace it. Since I have to unscrew thru the back where the water pipes connect the hot and cold

[@tinamenglish33]

Hi. I have a WA40J3000AW/AA that is doing the same thing. I checked the capacitor connections, stripped the insulation from TMR sensor to check for a broken wire and cleaned it. It still won’t spin. I put it in diagnostic mode and the hot water light blinks. I changed the door sensor, but still not spinning. It will fill, agitate, drain, but still not spin…Any suggestions?

[@JesseApplianceRepair]

usually those machines will lock at the beginning of the cycle. so if the lock was the issue it would not start. i saw you changed it which is the main code HOT WATER indicated. but now on the spin we have to check for any damaged wires going to either the actuator or capacitor. disconnect them and inspect them all the way around. I've seen occasions were the rip of the cable from the capacitor is behind and its hard to see unless you bend or turn the cable. if all that is OK then check the actuator is pulling the clutch to go into spin. if that is ok also check to make sure the machine is not going off balance. those machines had a recall so they added a tub sensor if it shakes a lot it will stop and restart the spin cycle and if it keeps shaking it will stop. NOTE ( TMR sensor uses 3 magnets inside the black plastic where it spins. removed the gear where the sensor is located and you should see a black rubber that covers the gears carefully remove it and inspect it to make sure the small magnets are there. they are small square shape. if they are make sure to clean that rubber peace and magnets so the grease wont interfere with the TMR sensor readings. Let me know what you find

[@antoninbrown4440]

Have this same washer but it wont drain, i cheak the water pump its not clogg and the lil cable underneath still intack. Could you tell me what could be the problem please if you can.?

[@tudor888]

Thanks for posting this video! Someone gave me a similar washer, it didn't spin. I found that the TMR sensor wires were broken so I repaired them. I tried to turn on the spin cycle without hooking it up to water, but it won't spin. Do I need to hook it up to water for it to work?

[@JesseApplianceRepair]

Under spin only no. Only if it says rinse and spin then yes. Let me know

[@tudor888]

SO, after I left it unplugged for a few hours, I plugged it in and ran the spin cycle. This time it spun the drum, I could see it from under the washer! The water pump was running too but no water came out. I can hear a little bit of water sloshing around in the machine but it's not reaching the pump, because the hose is empty. Is that normal?

[@JesseApplianceRepair]

@@tudor888 yup that noise is normal. It does it when theres not enough water to drain. Pump will stay on for a while then goes into high spin then stops for a little bit then it starts draining again.

[@tudor888]

Thanks so much for the prompt reply! I'll hook it up to water and test it tomorrow. PS: You're awesome!

[@lionelneals9078]

I have the same model washer. I did a diagnostic test and the Large light is flashing. The washer would start an run water longer than usual starts to wash and cuts off giving me the Large light blinking. What could this possibly be?

[@adriennesmith2133]

I washed a blanket on bedding. It washed but it would spin or rinse. I left it alone for a while then started a normal cycle for a test without clothes. And it went through its cycle without interruption. I repositioned the blanket just in case it was unbalanced. And as I mentioned before it did not spin or rinse. What could be the problem? Any advice? Thanks.

[@JesseApplianceRepair]

I assume the washer is similar to the one I have on the video... if that's the case then it sounds like the blanket is going of balance when it wants to start to spin. First make sure the washer drains all the water completely. if it doesn't then the pump is the issue.. bad pump or something stuck.. if it does drain next thing is checking the washer in other cycles by itself. no clothes. try at least 3 different cycles.... if the washer completes all the cycles then The shocks of the washer are the issue..even if you balance the load at the beginning the washer will still agitate and move the blanket around while in the cycle. and when it trys to spin it might shake and restarts itself and after a few trys it will stop. one way to check if the shocks are good in the washer is by pressing down on the tub while empty (no water - no clothes) . SO you put your hand inside the tub while completely empty and press down and release quick. if the tub goes down and up and stays the shocks are good. If the Tub Bounces more then once when released then the Shocks are bad. Let me know

[@HandyTim]

I can't find that sensor online would you happen to know anyone that sells it?

[@robcal73]

Where did you buy new sensor?

[@detrickmattear6473]

What did he clean the oil with?

[@HandyTim]

I just got the same washer and there's black grease leaked on everything what do you think caused that? The grease is on the belt pulley and has even gotten slung to the springs

[@HandyTim]

Actually I figured out where the black grease came from. Someone tried to fix the springs/rods using sticky grease and it didn't work. Now I'm thinking that sticky grease is on the sensor. Funny thing is the washer worked before sending it back out the door but now customer says it doesn't work at all.

[@cathinaisaacs2738]

Really would appreciate your help, I have the same model machine but the lock light is not coming on and it keep staying in a spinning mode but water is not going in to the machine.

[@brucewayne4211]

WA40J3000WA washer motor spins continually upon power on. This machine has had an initial problem of unbalance which was cleared by replacing all 4 balancing rods, Capacitor replaced, TMR Sensor replaced, and shift actuator has been replaced. All replaced for multiple issues found caused by the initial unbalance. At the moment there are NO fault codes but the motor runs continuously from power "on" and turns off 5 seconds after power button is pressed. The machine does not go into spin because the motor does not stop/pause to engage the gears and grinds the gears.

[@COVID-xr5mj]

Same

[@meemoo6885]

Hi jesus ,I hope you doing well, do you have the repair manual of those washers....could you share it with me?

[@JesseApplianceRepair]

Hello, Most machines actually have the Manual inside. some have it sinde the main control board. remove the back cover of the top head. other ones will have it stuck to a inner wall where the main tub is. if you lean the machine on its side and pick in you might see it. Hope that helps.

[@chelseaalexander7397]

@@JesseApplianceRepairI had one but cannot find the manual….please help….mine looks clean and brand new…checked springs last night and pump and hose….so I’m thinking it’s something small like you’ve mentioned….sensor or magnets….what are the bearings exactly?? 😢😂

[@lesliedaisley7846]

Bro what is responsible for determining the water level on these model I have one that is giving 2 problem 1st When adjust to the level of water eg : medium or high on completion of fulling to that level it automatically goes to Extra High on fulling level, the rense process is the same . 2nd issue: during the spin process coming to the completion process it starts nocking around in the drum ( Bang Bang Bang ) and the item been spin never get dry . And do these unit come with a tech sheet hidden anywhere in the machine

[@darryllbouyer7470]

HELLO DO I NEED TO BY THE HOLE MOTOR CLUTCH

[@sheilasantana1716]

I have the exact same washer it was working perfectly fine yesterday. I try putting it to wash today but as soon i push the start button the blinking light came on it won't spin just dead silence i was hoping maybe you can tell me what's wrong with my washer?

[@JesseApplianceRepair]

things to check. if as soon as you click start and no noise happened. Check your door lock. if it does not lock it wont start. if it does lock check water pressure. see if water is coming in. if not check faucet. but if it does start and adds water but does not drain to spin then its your Drain Pump. Let me know.

[@josephhostetler7788]

Need a new rubber bearing seal for a Samsung model no. WA45N3050AWA4 can you help me? Thanks!

[@user-cb3dp1ww3d]

Hi, I have this exact washer, and it stop spinning, and it's making a noise when it comes on, and it's not doing anything at all, can you help me, I kind of think I put in to many jean pants as well

[@jeffreyparnell4314]

What did you use to clean the gear? Also, is it possible to just clean off the sensor if everything appears intact? If so, what did you use? I appreciate the video. I have this same model and same issue. I’m hoping to fix it myself.

[@rafaelyepez13]

Hey. I have the same washer but mine shakes really bad before it spins and kinda shuts itself off. Doesn’t always do it but 95% of the time. Could it be the same thing as this video?

[@JesseApplianceRepair]

your issue is the Shocks. if the tub seems really bouncy then the shocks are bad.

[@ELBENDC2]

Hi, Jesus tengo una samsung flexwash el problema que tengo es que empieza a rotar pero se para estuve investigando y encontre que es el sensor MEMS pero no se en cual parte de la maquina se encuentra me puedes ayudar guia o indicarme done si es al frente o detrás, gracias

[@JesseApplianceRepair]

Ok so explicame todo lo que hace en detalle y yo te puedo identificar el fallo. Y dame el numero de model para ver como se ve tu maquina.

[@techie2003]

Hello Jesus I have a samsung washer model wa40j3000aw/a2 does not spin ...should I start checking the sensor first - I was able to start using self clean it did the wash ,but then it did nothing after that like it was stuck on sensor mode ..

[@JesseApplianceRepair]

Things to check *make sure the washer drained all the water. if not then Water pump has something stuck or is bad. *if washer did drain. check the actuator to make sure the gear changed. you will hear a click. *check for ripped wires. Now make sure you check really carefully. I have seen wires cut in very small spots that are hard to see. so follow the wires i show on the video and turn them and inspect them good. *capacitor can go bad but its very rare. *check for any grease on the Sensor like i show on the video.

[@johnbillmann7443]

Hi Jesus, My exact machine wont go into rinse cycle after wash cycle. It just stops and lights stop flashing, or it flashes a error code of Mid/ Extra high. If I turn off power and turn back on then it will rinse and spin load. Sometimes I will have to turn it to the rinse/ spin setting to get it to work. Any ideas what's going on? Machine is only 5 months old.

[@JesseApplianceRepair]

check the pump. to see if its working ok.. also. make sure the clothes in the tub are well spread out.. if the machine goes off balance it will stop the cycle. when you do the rinse and spin does the tub spin fast?

[@antoniohernandez2653]

saludos gracias x la informacion, tengo una lavadora igual que no me llega voltaje a la bomba de drenado ayuda x favor

[@ORRBOB4]

cant buy just tmr have to buy whole thig 180$ not good if wrong how did you get in diagnostics thx

[@JesseApplianceRepair]

Yeah the whole clutch assembly. It's rare that the TMR is not sold separately. What is your machine doing. ?

[@waynemoseley6028]

can a loose drive belt cause it not to spin?

[@jerimiahtanner3031]

So ive tried cleaning rhe sensor off and it still wont do anything, but i cant seem to find where to buy a new sensor/accuator, would you happen to have a link? To said parts?

[@lancehadey7186]

Where can you get that motor sensor