How to Find Samsung Washer Error Codes & Fix a Samsung Washer Not Spinning

[@DxJuliusO]

Sir, you deserve a round of applause and a trophy. You saved me a bunch of money and helped me fix my machine. Thank you.

[@noneofyourbusiness4805]

Hot/Extra High Then just Extra High Goes back and forth

[@GRINGOf10]

Thank you. You saved my life. My code was "HOT and Extra Large" --- took a pair of pliers and unhooked the door latch and it was back up and running again. Took 10 seconds. Without this video, I would have been clueless. YOU'RE A LEGEND MAN!!!

[@Brandon-bg2th]

Did you replace the door latch or just disconnect it and leave it off?

[@alenalana]

Hi I have these codes. Can you please explain more clearly how to do this procedure again? I appreciated your posting this comment.

[@hellokittyl07d09]

How did ypu get ypurs fixed mine has the same code

[@hanzischultz9284]

I have the same model washer. Following your video, I found one (green) of the three TMR sensor wires was severed. I think it is a design issue. The wires are too thin and it is so easy to be broken with that level of shaking when it's spinning. While I was fixing it I collected some data for testing the three components: Capacitor, Shift actuator, and TMR sensor. Hope it is helpful to those who need it. 1. Run capacitor (1). Capacitance = 45 µF ±5% (2). Check body shape. 2. Shift actuator (1).Ohm range: 1000-1100 Ω. (2) check wire. 3. TMR (tunnel magentoresistance) sensor. There are three wires: green, blue, and red. Using Ohm meter to measure, one should get these: (a) Green-Blue = OL (b) Green-Red = OL (c) Blue-Red = 10 KΩ

[@timothykelly2825]

Not all heros wear capes......

[@The7thRelic]

I got 1145ohm on the shift actuator is that too far out of spec?

[@JoeBuehl]

I'll join the chorus and say that this video showed me how to fix the exact same problem that my washer was having. There's no way I would have figured it out otherwise. Thanks!

[@morgangibson2999]

Hi first I wanna thank you for taking the time to show people this stuff and give us a bit of info on it. I have this exact washer and the codes are hot and warm. Which in the video states a unbalanced load I have moved the clothes around still no spining. I have even taken everything out and tried to spin and still reads hot and warm indicating unbalanced load really not sure what else to try I have unplugged the washer and retried the diagnostic again still reading hot and warm! Any information or help is so appreciated!

[@robertvuittonet6872]

Any luck trouble shooting this code Morgan?

[@getmoving7867]

I bought this washer and I can't stand it, I wish I would of looked up the reviews before I purchased!!!

[@danielklopfenstein9756]

Your exactly right Samsung's are junk and I should have never bought one either.

[@te_em_m5276]

Me too!

[@heatherrobinson1847]

Me to such junk from the day i bought it nothing but problems never ever again

[@jlm10181978]

We looked at reviews said it was good it’s a pile of shit

[@kelli729]

Me too

[@stevianz3398]

Thank you so much for taking the time to share your professional knowledge and experience with us.

[@KyleCross16]

I have this washing machine child lock flashes and hot water flashes after first rinse it doesn’t spin can you help me

[@Aeon1989]

I've had my washer here for 2 years. Just today got an error code of Hot and Low which my manual says "ensure the cold and hot water tap are connected properly." I followed the lines and matched the pipes for hot and cold, even undid the lines to make sure that's what the connection was and low and behold, they were reversed. Thank you Best Buy techs...not only did you wash my manual in the test run you hooked me up backwards

[@eland4914]

Extremely clear and concise informative video! This will allow me to at least go into the issue not so blindly.

[@iqraali-rk5pu]

I have question so at night time I turn on the washing machine to watch the clothes but when I woke up and open the machine since it said it’s finished but when I open it had water to the top and I tried to turn it on to suck the water but it did not work. Do you know what’s the problem? I am using Samsam washing machine

[@Bearrden]

YOU! are the reason youtube is amazing!

[@geneleis6111]

My washer has the first listed error code, the "HOT" light only blinks. According to your chart the door lock is damaged by forcing it but it has never been forced and appears OK. Anyway the error prevents it from operating. Thanks for posting this video and the codes.

[@jacquicompton8108]

Yea. This is my issue as well. Any idea how to fix it?

[@jenniferpenarrieta-lopez9970]

Mine too looks like a lot of people have this issue but still no answer on what we might have to do

[@erichickman1]

same issue here😊

[@SusanPolk-zo7nk]

The code I got was Hot & Warm flashing. I checked the 3 things and all wires are connected. The spin cycle runs and then makes a sound like gears stripping. Can you help?

[@elbeezaya9673]

I got the same problem did you solved the problem?

[@jamalmills2838]

I got the same problem​@@elbeezaya9673

[@aztecgirl1076]

Any updates?? I'm currently having the same issue 😭

[@kellyewood6173]

Hi Ben, Thank you for sharing the how to. I have a Samsung washer looks similar. My model is WA44A3205AW. The water inlet was changed because the water wasn't filling the machine. So what could be wrong with the machine?

[@DJLast1977]

Fantastic video. I also got the Hot & Cold code, and have had trouble with the washer not spinning at the end of a cycle. Oddly, if I shut it off & turn it on again, I can put it just in Spin mode and that works, so I had been doing that to get my laundry finished prior to seeing your video. After watching this video I feel confident going to go under the machine to see what's what now that I know what to look for. Thanks again!

[@shawnparton5384]

I have the exact same problem did you figure it out

[@stephpatrick80]

Same here

[@AndrewAuger54]

yeah, been doing the same thing, after a while it just gets harder and harder

[@karlylewis4038]

Same thing is happening with mine, did you find out your problem!?

[@eugenehoyte165]

Hi Ben. Thanks for the video. My Self-clean has a heavy vibration problem when it is draining out water, that shuts down the machine. It then begins to beep and the lights begin flashing. Thank you in advance for your advice

[@craigwoods6947]

Same here Ben any help with this problem.

[@franciscogarcia8125]

same exact machine, it just makes a lot of noise on the spin cycle but doesn't spin

[@bharris3242]

Did you figure out what the problem was?

[@felo8042]

@@bharris3242same problem no meter

[@michealwilliams5518]

Great evening Ben, how are U? I have the exact washer U are working on. My statement is, my washer makes a humming noise not allowing the water to fill, the lights still come on and even the function of the buttons, but no water filling.

[@csubroncs]

During the spin cycle mine will spin up for a couple seconds and then stop. It then just sits there stalled out. Drain works fine at the beginning of the cycle and empties the tub. On the diagnostics, all lights are red and the Hot LED is flashing. Model WA40J3000AW/A2. Capacitor wires look good and no bubbling. Lever arm and cable look good. What do you think? Same sensor issue?

[@CountSalazar]

I have the same issue and we barely bought the damn thing. It washed normal the first few times but now the water empties but it doesn't spin the water out. It just stops.

[@csubroncs]

@@CountSalazar I bought a new motor and clutch assembly and the issue remained. Ended up buying a new one.

[@CountSalazar]

@@csubroncs we ended up returning it and getting a whirlpool. Good thing we had barely bought it. No more Samsung appliances for us that's for sure.

[@taotaomotna5395]

I have the same problem turn on door locks clicks but water does not fill then clicks then it starts to drain but no water in machine I Eaed the ts but still no water coming in help leader tks , and warranty is over.

[@freddiegroomster8056]

Mines just sits and produces hmmn noise and not spinning. What should I do?

[@mbing3111]

What luck! This is the same washer that I have and it has an issue that i couldnt find in the diagnostics. It stops mid-cycle and all of the lower lights go on with the extra-high light blinking. I know that there is something off with the water inlet valve because it will keep running into the tub even when nothing is going on. What would cause a diagnostic like the one I am getting? Yours is the first/only video that addresses my model. Feeling encouraged. Thanks, Mike

[@tanikalane3097]

Thanks for this video. The error code that I am getting is the Hot LED light blinking. Any suggestions as to what the problem may be and how I might fix it???

[@legendhasit557]

Same here I have the hot LED light. Where you able to fix?

[@jenniferpenarrieta-lopez9970]

That’s what I have it says the door issue but it does lock and the door doesn’t look disformed

[@bradymenesses9338]

It seems like no one replies or said that they fixed the problem mineis doing the same can't figure it out. Someone anyone please 🙏 help

[@bensappliancesandjunk]

*PLEASE READ THIS BEFORE COMMENTING ASKING WHAT A CODE IS* : I am getting a lot of people asking about what certain lights mean: Please make sure to watch the list from 03:02 on, because many of the light combinations are both on screen visually, as well as text-based just to the right of the color/light combos. If the first code shows "HOT", then the rest of the boxes show what HOT means plus any additional lights. Its all there in the video, please view them. Thanks!

[@sobxthooly7951]

Tried the discord link. Won’t pull up. Also how can you tell if the tub bearings are bad on this model. I have same, no spin issue. Done everything you recommended and much more I’ve researched. Tub bearing is the only thing left I can think of. I can feel a tiny bit of play on the shaft under agitator cover.

[@bradymenesses9338]

Found code check problems can not figure it out hot blinking help please

[@damarioneverett1211]

My machine flash red on washing. Just a small bit of water comes in

[@richardlapierre8571]

Thanks sincerly. We need more people like you in this world...☺

[@angelvite5536]

I have this same model washer i think based in this video my issue is the door look switch, my question is if you have any idea on where can i find the whole top part that have the switch and holds the top lid and control panel ??? Because in my washer that whole part underneath is corroded and if i can find that part and is not that expensive i will rather buy it and not only the look switch, thank you for your time and this video which is very helpful

[@bkcurtin2621]

Right on dude, found a broken green wire on the TMR sensor connector in about 15 ninutes with the help of this video! Thanks & keep up the good work!

[@bensappliancesandjunk]

Awesome! I'm glad you were able to verify it was a bad TMR sensor wire.

[@bkcurtin2621]

@@bensappliancesandjunk none of the local appliance parts dealers had a clue what it was, much less could provide one. I soldered & insulated the broken wire, also clipped off the zip tie holding the mate connector for a less stressed angle. Machine works again!

[@bensappliancesandjunk]

@@bkcurtin2621 Funny story. About a month ago, I had a guy bring in this EXACT washer to my store. Complaint was it'd try to start spinning up, then died. I looked at him and said "Bet its the TMR sensor". He had a deer-in-headlights look. He just said look at it and he'd pay what I wanted. Take it apart and sure enough: Wire was frayed. Fixed it and told him. He then admitted to me he was a factory-authorized tech for Samsung for a few years, and he couldn't even figure this one out because it had a standard motor instead of a stator. So somehow, me & my shop know more about Samsungs than the Samsung techs themselves know. It was really funny to me.

[@jeffreyb4481]

Thank you, Ben. I got the same code as in this video and the exact same problem. Luckily I have a soldering iron - result was a no-cost repair done within an hour of watching this video.

[@lwvmobile]

I've had this washer for a couple years now, and every so often I just want to toss it out. Its such a pain in the butt when it doesn't want to start, or drain water, or unlock the door. I've already had it serviced once, and to be honest, its probably just too smart for its own good. Meanwhile, my step father has a 30+ year old Washer that just won't die.

[@amyloves9940]

Its the old things that last longer, even automobiles. But, I am having the same exact problem, wont drain, but this began after 2 years of its purchase date.

[@sh1310]

Same. Can't wait to set the thing on fire.

[@carlenecascoe9650]

I would like to know what brand of washer, that your step fathers has???

[@lwvmobile]

@@carlenecascoe9650 Whirlpool, I believe, but usually it's the same machine and different brand name on top of it. I have no idea what the model number is, but it's from 1990 or so I think.

[@carlenecascoe9650]

@@lwvmobile thank you so much, for the information! I purchased my Samsung washer just a little over a year ago, I am having problems with it already! I’m going to have to purchase another brand, I just can’t do without a washer!!

[@JuliaMcMenamin-i7q]

very helpful video! Can you tell me how to calibrate this model? I keep finding instructions for a different samsung that involves pressing the delay button- but this model doesn't have that button so I'm stumped

[@terrapinflyer273]

I'm not finding any calibration option or secret button combo for this one either. Despite Samsung explaining it as an option for some models. I suspect it's just cheap trash that Samsung used as a money grab and didn't bother including this function.

[@jamesshackelford6787]

You may have to press power, start/pause and temp at the same time to get into diagnostic mode.

[@michaelwielenga8809]

Thank you for that comment

[@southernbelle850]

Thank you!!!!

[@wayneallen2297]

Thank for showing me how get washer diag mode .... all lights flashing and washer would stop filling .... once I new what touble code was (exrta large light flashing) found it was a water suppy problem( screens pluged with rust due to high iron content in water ) cleaned and all is well !!!! Thank you you saved me a bunch of $ for a service call ...I have been an auto tech for 30 years so figured i could fix it ... Thank for you guidence....AWESOME AND WIFE IS HAPPY SO SAY NO MORE!!!!

[@007g35]

I appreciate you taking the time and sharing your wealth of knowledge. We had this washer for little over 6 months, and it is great aside from the main issue it does not auto correct an un balanced load (Which is everytime) when this happens it will automatically start to fill with water. We usually, more often than usual would manually redistribute the load until the clothes can spin dry enough to place in the dryer. It takes about 3 hrs. to do one load. My old school washer was set and forget it... I miss that. Any insight would be greatly appreciated!! Great video!! I just subscribed! Thanks very much!!

[@codykraemer843]

Same problem here, every time you put a load no matter how large or small. Really irritating.

[@christoon7848]

Was really hoping their would be an answer in this comment for this issue

[@Themetalscrunchie]

We've had the samsung wa45n3050aw/a4 for about 2.5 years with no issues on the machine until about a month ago. Suddenly the machine is knocking when attempting the spin cycle on the quick wash with low cold water, stopping, and giving the unbalanced load error code. We're able to limp through a load by pulling out wet laundry and redistributing within the basket, however we have been unable to process laundry as we had consistently for the previous 2+ years. There's been no significant change in the loads we're attempting to wash and I don't know why the machine would start being extra sensitive to unbalanced loads, or become unable to rebalance itself as I assume it has been doing up until now. I honestly don't even know where to start. Any guidance or suggestion would be greatly appreciated.

[@frantzantoine3017]

I'm having the same problem takes about 3 hrs to wash a load and the it keeps switching to load can anyone assist please

[@pcofranc]

@@Themetalscrunchie I use my neighbors machine similar to this but has a small screen and will display code UE for unbalanced load. The only thing I suspect that there *might* be a counterbalance system with weights that helps offset unbalanced loads and maybe that is not working? I dealing with UE right now with blankets. Just pulled two blankets out and praying for it to finish.

[@bird2002]

Your video inspired me to look underneath my washer. As soon as I tipped it over, I found the blue wire going to the capacitor had been clipped. I reconnected the wire and my washer was fixed. Thanks so much for this thorough video.

[@bensappliancesandjunk]

Awesome! These things are notorious for having a wire shredded either on the capacitor or the TMR sensor. The one we did this video on had this ULTRA SMALL wire (like a 22awg) that was ripped out from the TMR sensor. To replace the TMR sensor, you had to buy a new friggin' shift assembly @ $150. We spliced the wire back in for 50 cents after some DIY-ing and it worked like a million dollars again. They should re-enforce the wires way better than what they do.

[@ServantSoundProductions777]

Hey Alberto.. what problem did the clipped blue wire make for you??

[@ServantSoundProductions777]

@@bensappliancesandjunk thats crazy Ben.. they kno what they're doing... they make certain parts that way, so "THEY" can make even more money, by charging outrageous prices for something so easy to fix

[@bird2002]

Mine wouldn’t go into the spin cycle properly, but it would also disregard my selection of small/medium/large load and go directly to extra large. Then it wouldn’t go through the spin cycle, it would freeze up during the washing cycle, and was an overall disaster. It has actually happened to me about 3 times in the last 4 months. I suspect that the vibrations eventually cause the wire to become so maleable that the wire eventually snaps. It’s quite a design flaw.

[@bird2002]

Now I’m getting a different error code. Cold is the only one blinking now. The machine stops mid-cycle and changes itself from medium to extra large load and continues washing. It’s the weirdest thing. Ever seen this before? It doesn’t matter the load size, it always stops, changes to Extra Large setting and fills itself to Extra Large level of water, and then carries on to washing for hours. It’s getting very annoying.

[@cynthiasoto3178]

Hi Ben! My washer looks almost the same, except it has a soil level selection. I've had mine probably a month now and I noticed it will spin, then stop and spin again, etc. My clothes feel too wet at the end of each cycle. Any suggestions?

[@libbylink]

Your load is probably becoming unbalanced during the wash and/or spin cycle. I usually stop the spin cycle and rearrange it and it works fine. I find it does more often if I'm washing heavier articles like blue jeans

[@stephancobbert9899]

Hi, thanks for your time in explaining these codes. My machine isn't spinning and it does show a hot blinking code when I run the diagnostic test. How much do you estimate it would cost to have the TMR sensor replaced, if it is that particular sensor, by a technician because I'm for certain that I can't fix that sensor myself?

[@bensappliancesandjunk]

The TMR sensor cannot be replaced by itself. You'd have to buy the entire shifter/transmission column.

[@lisakeith9968]

Is there anyway to bypass the lid lock? I have this model and get a Hot flashing led.

[@chadcoleman5160]

Remove the lock assembly, cut all the wires, and discard the lock assembly. Strip the Green, White, and Red wires. Twist the green and white wires together, and leave them together. The washer thinks the lock is LOCKED when the Red wire is added into the Green and White twist ( all 3 twisted together ). You can't leave all 3 twisted together all the time because the washer also looks for it to UN-LOCK. Leaving all three twisted into the LOCKED configuration seems to activate the pump a few seconds after the power is turned on . So, only add the Red wire when the door is closed and you want to begin a wash cycle. Remove the Red wire from the twist, after the wash cycle finishes, and before turning on the POWER for the next wash cycle. Leave the Green and White wires twisted together all the time.

[@maggieb1074]

that didn't work for me. any idea why? I followed instructions to the T

[@ericcorrado2446]

I have the hot and warm flashing lights. Unbalanced code. It doesn’t seem to matter what I put in there to wash and whether it’s SM, MED or LG load it still stops and sets off the code. Any advice on what it could be would be greatly appreciated!

[@Seanith]

Did you end up replacing it?

[@jenniferpenarrieta-lopez9970]

I have the “HOT” flashing only meaning there’s an issue with the door The washer fills up but doesn’t spin it drains right after filling up and the door locks and doesn’t look disformed please help what should I try next

[@brittneyyyann]

I’m having this exact issue, with the draining and all. Did you find a solution? The door is definitely locking as well.

[@ricardog755]

Do u fixed i have same problem hot flashing😢

[@Rickdogg389]

You da Man!! Getting HOT error code. I actually disconnected and reconnected all the connections at the bottom and checked for broken wires. Tried to re-start washer and it still didn’t kick on. I removed the 2 screws for the door latch and took the door latch apart moved parts around and put back together and re-installed. Push Start and BAM it started working.

[@ronmccarty7537]

Thanks! Very well done! Can’t wait for the next video

[@bensappliancesandjunk]

Thanks for watching! I'm trying to get back into doing more videos frequently

[@esco361]

Great video. What reading should u get when testing the tmr sensor?

[@MrJames1111111111]

I have this same machine. I start my load on small. It fills with water and starts the wash cycle after filling. It wash for about 3 minutes and then it starts filling up with water again, it not only fills up, it fills to a extra load.

[@Dusty.Does.it.]

What was your fix?

[@bird2002]

I have the same problem, any fix available?

[@MrJames1111111111]

I just got rid of it

[@bird2002]

I’m considering the same option

[@Dusty.Does.it.]

@@bird2002 yeah just throw it away, no technician in my area even wanted to try an fix it. It’s sitting in my garage collecting dust

[@carolinasarasty4434]

Hi I have the same washer machine the code I got flashing hot and warm ? Everything you mentioned I looked at and is all connected what do you think it might be ? Thank you for your help and informative video

[@desmondfreeman2439]

Giving sound but not spinning

[@jaycobvallejo2974]

Hey nice video . I have the same washer but it’s shaking really bad I’ve replaced the suspension rods and it is still shaking they are an inch bigger then the factory rods will this be an issue? Any other parts to check that might cause this problem?

[@martinrick1976]

Hey Ben I’ve got a washer that shares function with the Temp button with the * feature to hold for extra rinse so it’s not entering into diagnostics mode any suggestions?

[@lauraz9564]

I would LOVE if you could figure out how to disable the chime on this exact model. According to the manual and Samsung, it's impossible on it. It's driving me and my family bonkers. Please help!

[@J10969]

I only had the HOT light flash. The code guide you posted says it’s a problem with the door. But my machine works fine and there’s no issues with the door as it locks into place every time. The issue I’m having is that I’m only able to wash my clothes in hot water even when I select cold. It is hooked up right as it used to work perfectly fine. Any ideas as to what the issue is? 😥

[@tiffanyriley6376]

I'm having the same problem!! Ughhh

[@kerriclement7592]

Thank you the information our code is medium not sure what to do ? Can you tell me if it is easy to fix or need to call someone to fix it .

[@christywright4701]

Hey Ben, I wish you made house calls! Thanks for the great video and for sharing your knowledge with a bunch of us, that will never by a Samsung anything again!

[@joegallagher403]

Thanks for the video. I have a door lock issue. The lock does lock but the light on the panel does not light up. This is causing the water not to fill. Any suggestions?

[@legendhasit557]

Same here my lock does lock but nothing happens after that

[@jenniferpenarrieta-lopez9970]

Mine locks and fills up but drains right after filling and doesn’t spin

[@DVelasquez-w7e]

My Samsung 3021 top load washing mashing is not draining the water

[@kelleyrentfrow1457]

Hi,1st I think your absolutely wonderful for helping people! My J3000AW W/A won't drain or spin,it's fills up with water goes through the wash cycle then quits. I tried sucking the hose out with vacuum that was a mess should have used a shop vac(lol). Anyway no change. I've tried resetting to no avail, the small button flashes when I do a diagnostic check on it what am I not doing, or better yet any idea on what to do. Just don't have money for someone to fix and have alot if clothes to wash. Thanks in advance! If you can help me you will definitely be my hero and I will tell everybody I know to check you out.

[@adufresne1538]

I had the same issue, did you find out how to resolve the small button flash problem?

[@andishabazz2660]

Hey Ben, Your video is super informative. I don't get an error code when I press the temp button and hold it. My washer worked fine till I decided to take it apart and clean it per following the instructions from another youtuber. It works fine but is off balance when I wash clothes. If I run a cycle with no clothes, it is fine and spins just perfectly. Any help would be greatly appreciated.

[@carolinemcclain1616]

Hey Ben. Awesome video! I have the exact same washer. However, I tried to pull up the diagnostics mode and nothing happens. I followed your instructions and turned the machine on and then held down the temp button for 8 seconds. There was a sound after 3 seconds but no lights came on. Any tips?

[@ghostwindcorsairs]

Thank you for this video. I'm having a weird issue. The diagnostic shows an Extra Large LED flash and it won't spin. Any ideas? Thank you again!

[@gregguiney7107]

My error code is HOT and DOOR LOCK. Would this indicate a problem with the door connection? We were able to get it started again by pushing down on the door while pushing start. I didn't if that indicates a problem with the door or was just a fluke pressing down on the door. Thanks for you're video. 😊

[@nayracuza2109]

Hi!!! I’m going crazy with this washer machine. Thanks to your video I’m getting the unbalanced code hot and warm flashing light and spinning sign, but that is happening from a week now with every load of laundry, small big light and heavy. I don’t see any solution in the manual that you show here in the video and don’t know what to do about it. Appreciate your help and time.

[@Seanith]

Did you end up replacing it?

[@nayracuza2109]

@@Seanithyes

[@amandaholmes9102]

On the model you talk about mine had a ( AW/A2 ) at the end is this the same model motor that you have in your video before I go putting it on it's side.

[@ashleycrisler2632]

Hi, thanks for the codes & info. I have the small button flickering as our diagnostic issue. We have removed all water from the tubes, unplugged and taken everything apart to make sure nothing is clogged or stuck inside nothing was. The water will drain but only when out of the wall & into a bucket low to the ground. Would you say this is a pump issue that we would need to replace?

[@breezybree2743]

Did you figure it out? Mine has the small diagnostic issue too

[@ronaldclemons5520]

Ben I have the same washer that you are working on. My wife set water temp at cold, and she says water comes out hot. Is the temp thermostat getting bad? Thanks for feedback🙂

[@vijaygaming2123]

In any mode of washing the water is not cut off its over flowing , could you explain the reason for this?

[@stephanietracy1853]

Thank you!!! We had the extra large blinking at us. Our water intake filters were full. Saved us a lot of money!

[@ACKlulu]

That is what mine is doing. Was it easy to fix?

[@jessicacuellar3582]

@@ACKluluwere you able to fix?

[@dia1661]

Thank you for posting this video. My washer is randomly not spinning. Not giving an error code. Only the cycle I choose is flashing and the actual light for “Wash” I’ve tried to contact Home Depot but it’s 4 months over warranty. Need help because I still consider this a new washer. Brought it last July.

[@charleswise17]

Thanks! Wife ordered a new washer but we were able to cancel the order and fix our old one. (Clogged screens in the water valves)

[@russellgirvin9181]

Thanks for the video,it was exactly what I was looking for. I have the same error code in your video and I've checked almost everything. I haven't started taking it apart yet to get to the tmr, because I noticed on my washer that there is a excessive build up of dirt and dust from the belt. It's also very loose. Is there a chance that it could just be the belt? If so do you have the information on the belt ? Before I seen your video I took it off by hand. Very easy I might add. Thanks again for the video and your time.

[@josesanchez2202]

Hello. Thanks for sharing this video. Can you help. I did the diagnostic steps and the light for the hot water is the only one blinking. Thankyou

[@BobaJett]

The button you say to push on mine has an additional Asterix underneath it, so when I push it once it hits three seconds it adds that extra rents feature in. Other than that, it’s an exact replica of the model you’re working on how do I enter the diagnostic mode on it?

[@lauraroche3282]

Good morning! So happy to find a video on my machine, but my temp button is a dual button. The bottom has an asterisk for extra rinse. How do I get my machine into diagnostic mode?

[@spot9123]

This is exactly what is happening to mine. Mine flashes Hot and Warm which is an unbalanced drum. We had a guy come out and “fix” it and he only replaced a part on it. We try to balance the clothes we put in. Most of the time if we put something like a thick blanket it will not spin. What I’ve done is just put the washer into spin mode and it spins. This washer is a pretty faulty machine to be honest but atleast you do have a washer. Thanks for teaching me how to find out what is going on with my washer.

[@bensappliancesandjunk]

My opinion would be to maybe look at replacing all 4 matching suspension rods on this model. Not the cheapest, but these are very prone to flaws and breaking down quicker than other brands.

[@spot9123]

@@bensappliancesandjunk oh alright thank you for your opinion and I’ll look into it.

[@peggywilson4875]

I also got the Hot & Cold code, and have had trouble with the washer not spinning at the end of a cycle. Ben any suggestions... we checked the wires that you suggested

[@jordanloomis804]

This is a great video!, thank you Ben! I scanned the comments and didn't see this asked....my washer is flashing "medium". Do you have a video or instructions on how to change the water sensor or check for a clog?

[@ChristopherCluckey]

Thanks for the tips. I'm getting the Extra Large flashing error code. I did clear a small obstruction at the water line connection. Water runs, but the code comes on and empties before completing the wash cycle.

[@toddcopley5717]

Hi, I have the Samsung washer you tested. My problem is washer won't power on at all. I checked outlet, plug and pulled control board out. Tightened all connections and replaced. Still won't powe on. There is a yellow diode flashing in the middle of the circuit board, that goes off and on every 3 seconds. Any ideas? Thank you, very helpful video.

[@trishaivy7887]

Thank goodness for ur video !!! We followed ur instructions and the code for ours was the Hot and the Ex Lg lights were ones flashing. Door lock switch terminal is connected and correctly or is broken... This occurs intermittently because of electric wire leakage or main PCB fault. How do we go about fixing this? Thank u so much in advance

[@trishaivy7887]

If anyone has read this ... Can u plz help

[@ASR-BA]

Thank you for making and sharing such helpful videos. I have SAMSUNG Refrigerator and the ice maker is keeping icing up as soon as the bin gets full. Every time I defrost it and removed all ice then it is all good and when the Icemaker bin get full then the icing starts building up and stop making ice. I hope 🤞 you have some solutions to this type of problems. Thanks

[@juanflores1812]

Hola amigos necesito ayuda porfavor

[@alvarocaban9403]

After all is checks are done and every sensor checks out good to include the TMR sensor what do you think can be wrong when it still don't spin.

[@MossmanBonsai]

Thank you for the video, the code I have was hot and warm flashing, haven’t seen that , what do you recommend thank you

[@ricardog755]

I have same problem hot flashing do u found the wrong part???

[@Seanith]

​@@ricardog755 Did you end up replacing it?

[@jesseholeman9004]

I have this exact model and sometimes it would spin the water out and sometimes it wouldn’t, and just yesterday it stopped filling with water altogether… the code I’m getting is the “small” led on the load size. What do you recommend? Thanks .

[@ChristiBWillie]

Thank you so much for this video. Mine does not blink any codes. It spins but stops mid way and will not finish. Suggestions?

[@victoriamoore6200]

Hey, any luck with your washer. Mine doesn't blink a code either and stop midway washing also

[@brielle6888]

Anyway you can do a factory reset on this washer? I have the exact same washer it is not pulling cold water. I am going to do the diagnostic system now.

[@KM_i_am]

I have the same model washer. Following your video, my error code is the flashing hot water, but I do not see this error in the sensor code section. My machine's issue is it does not spin. I know your example is the TMR sensor issue - could my problem be the same even though the cold water light does not blink? Any insight is appreciated as I am trying to fix this myself. Thank you in advance for your help.

[@ronum976]

Excelent video. I have similar issues, the shitft activator has 1160 ohms. Do you think I have to replace it?

[@GoldshackGarage]

I flipped mine over and wiped down the TMR sensor with a rag because it was all greasy, I really think this fixed the issue.

[@cwill2429]

THank you for what you do. I myself have a question, have a one year old Samsung washer (model WA45T3200A), the cold cycle does not work, any ideas? Thank you.

[@bensappliancesandjunk]

Test the water valves for voltage AC with the multimeter. If it gets a hundred and twenty volts, then the valve is bad, but if it does not get a hundred and twenty volts that it is possible that main control board is bad

[@ThePanther2244]

Good video. My washer wasn’t running water, And the simple diagnose helped.

[@AGS_41216]

mine was also not running water. The quick test/error code confirmed this. How did you fix it though?

[@marcneeley6835]

I have the same question

[@JonathanEnglish814]

Hi, thanks so much for this guide. My washer is consistently showing the load is unbalanced, even without a load in. I've gone through several guides i've seen online to no avail. I've also made sure that the machine is indeed level. Any advice?

[@roni8920]

Mine is doing the exact same thing, did u ever get an answer?

[@patrickmalagisi7897]

Great video. Any idea how to turn off the alarm sound on this same model?

[@augustharlacher5660]

I wrote a comment to you, but somehow, it's gone. Well anyway I did the code check, and I am getting a hot and cold blinking lights with all the lights on for the load size. Right now, I am going to see if the line is clogged. Hope that's all I have to deal with.

[@totalkaos6969]

Thanks for the video. Can you help with the spin cycle imbalance problem?

[@christianmyers8258]

I need help to

[@christianmyers8258]

My washer wants to spin it makes a couple rotations then stops and says unbalanced with only 4 things in it

[@bblod4896]

I appreciate the video. We have the same Samsung. The machine will start to fill with water, then sometimes, it makes a strange noise and water slows down to a trickle. I wonder if the valve is sticking or not opening all the way. I tapped the valve and the noise went away. I'll order new cold/hot water valves.

[@llaughery]

Hi, I have this same washer model. I enter into the diagnostic mode and the hot/cold flash. Been dealing with this crappy washer since I bought it new in 2016. Any how the laundry does not spin out right leaving laundry soaking wet. I can't tell how far the cycle gets bf the washer just sits and does nothing. I've gone through all the different wash choices and all turns out the same. Clothes not coming out clean and soaking wet. Last night I decided to try washing laundry on the self clean cycle out of frustration. The washer went through the whole cycle and the laundry came out spun correctly. I did this same thing to 2 other loads of laundry and the result was the same, completed cycle and laundry spun out right. After all this info :) Can you tell me what would be wrong with the washer specifically? What remedy or part would I need to fix this thing? Also, watching your video and seeing the belt under the washer, my belt is a lot looser than 1 in vid. Is that a common problem with this model/brand. I looked for broken and loose wires where I could see them except i didn't take apart anything to get at that 1 little part you mentioned. Sorry i can't think of name atm it's 3 letters. Dmr I think? If you could advise me on this it would be very helpful and thank you very much...

[@TheSouthernSkunk]

If it won’t go into diagnostic mode would you think control needs replaced?

[@Zion3d7-pi4ls]

I have a Samsung washer model WA45N3050 AWIA4 and cannot seem to find how to calibrate the washer drum. Do you have any info you can share?

[@stingsting115]

Thanks man I got my washer to start working and start spinning after watching this video but a couple of days later now with the same wire fixed it won't stop spinning do you have any idea what that is

[@javieracosta7860]

Good morning technical friend, I have a similar fault in a WA19J3000AW model in the diagnosis the hot led is the one that flashes, I appreciate your collaboration to correct this fault. Greetings from Venezuela

[@karlybecker7454]

If the mulex connector won’t come out of the shift actuator is that a pretty good indicator it’s the issue?

[@jenn1736]

I have this same washer, yesterday it was blinking LED Hot, the door is locking and unlocking fine. I’ve went through the test modes, the only things it would not do was dispense Hot water and with the spin cycle it just makes a humming sound, it did agitate for the motor test. After I went through the test mode, I checked to see if the error code was the same and now it shows no error code. But now when I try to just start it as a normal wash as if going to start fresh with a load of laundry, it dispenses no water and just hums. What do you think this could be? We thought maybe the actuator? Is the actuator and motor clutch the same on this washer?

[@AmyJones-tv2bm]

I have a similar model, WA45N3050AW/A4 that is doing the same thing! can you help??? it's giving a hot and warm blinking led during the spin cycle, manual says to redistribute load and re press the start button however this does not fix the issue. it will not complete the spin cycle at all, when it begins to spin, the basket hits the sides of the washer in all directions and never fully starts spinning, after it stops trying, it stops, unlocks, and starts beeping and giving the flashing error lights again.

[@elizabethlamont1246]

Mine does the same, seems to be off balance but after I move the laundry around and try to “spin only” it still will refill and then drain and spray rinse and never spins out the clothes.

[@jenniepirnie1792]

FYI- Samsung regulates how hot the water can get. Putting it on hot will not solely draw hot water. It adds cold water as well. We needed straight hot water, so we bought two Y connectors with shut-off valves on each branch of the Y. One is hooked to our hot water spigot. The other is on the back of the washer on the cold water intake. We then added a black hose that goes from the hot water spigot to the cold water intake. When I want hot hot water, I open the valve on the Y at the hot water spigot, close the valve where the cold water line hooks into the Y on the back of the washer, and then open the valve where the hot water is coming into that same Y. Now I trick the washer into putting hot water into the machine when it thinks it's bringing in cold water. So dumb! I'm capable of deciding how hot I want my wash water to be. Hot, hot water is 100% necessary when washing clothes worn by welders, mechanics, engineers, farmers, etc. Not everyone wears casual clothing and stays relatively clean at work.

[@ButtersCCookie]

Very smart. I can't stand this company. They censor advice on Facebook. And brag about overcharging for products and parts. Our government approves. These things are not spontaneous. I just boil a stock pot of water. Start off small load as hot water turns on increase load size.

[@Penniare]

Thank you Ben, I have the same unit, same code. all wires good. had a broken ground wire, repaired the wire. still it does not spin. it starts to spin and stops 4 seconds later. capacitor checks good. However shift actuator checks 1126 ohms. can that cause this issue? or is 1126 within +/- tolerance?

[@GoldshackGarage]

Hey man, I just read mine and it's at 1103, what you found out about yours? Is 1126 in range?

[@zebydeura9404]

Thank you for your knowledge! Our washer stops in the middle of washing and we have to turn the knob to rinse and spin so it can finish washing. Do you know what may be the issue?

[@bensappliancesandjunk]

On a Samsung like this? Sounds like the PCB logic isnt doing right.