SCHNEIDER ZELIO - 3 pumps cyclic operation programming..

[@pramodvs1108]

thank for the above video. But is it possible to do manually on the PLC.

[@aselawickramarathne7253]

interested....keep it up

[@kashifnaveed4494]

Great sir

[@anarghyanagesh895]

can we make a similar program for two pumps using counters?

[@sennapparajan.p]

hi .. yes you can use. you have only 2 pumps? for only 2 pumps you can use impulse relay...

[@manilakshmi6118]

Good, but I have one doubt ji, if any one motor trip how the sequence running. My project 4 no's motor running sequence 1234then again 1234 if any one motor trip or off that motor only skip in program. Other will continue running sequencely pls give Idea

[@sennapparajan.p]

if all the motor is running then there is no sequence .

[@manilakshmi6118]

@@sennapparajan.p ji, float switch on, No1 motor on), 2nd time float switch on No2 motor on, motor1off. Same pattern next output. then the sequence go throw until No 4,after again come to No1motor . In between any one motor trip automatically sequence go throw next motor. How will do?

[@sennapparajan.p]

@@manilakshmi6118 WILL DO A VIDEO...

[@manilakshmi6118]

@@sennapparajan.p when you upload video about my logic

[@manilakshmi6118]

Ji any one motor trip in the your sequence. how will it run?add to do Trip logic circuit in the program and upload onemore video pls......

[@jaypatelsteam]

Thanks for explanation

[@sennapparajan.p]

you are welcome... kindly subscribe...

[@Rushymuh]

Thank you for the explanation. But I found an issue in the program: When 7th time pressing the PB (pressure input) 1st & 2nd pumps should work but still holds pump 3rd & 1st. Please clarify

[@sennapparajan.p]

issue with your program or program in my video??

[@Rushymuh]

@@sennapparajan.p I tried similar program, but I found the 6th & 7th presses are activated same pumps 1 & 2 twice.

[@sennapparajan.p]

@@Rushymuh please try once again following the video...if cycle restarts in 4th push then it will continue.... no change of error in 6th or 7th push....

[@Rushymuh]

@@sennapparajan.p Similar program checked and still I have the problem after 6 & 7th outputs are the same. REASON: After 4th PB pressing C1, C2 & C3 count 1, C4 resetting In 5th - C1 reset, C2 & C3 count 2, C4 count 1 In 6th - C1 count 1, C2 reset, C3 count 3, C4 count 2 In **7th - C1 reset, C2 count 1 & C3 count rest, C4 count 3 **At this 7th PB press C4 not resetting itself. So, output holds as in 6th.

[@sennapparajan.p]

@@Rushymuh send your program will check [e-mail]

[@kashifnaveed4494]

Make a video on chilled water pump with differential pressure transducer with siemens logo.

[@sennapparajan.p]

please mention working logic...

[@MrDhainesh]

Hiii bro, i have some queries on this. Possible to clarify?

[@sennapparajan.p]

Sure… yes…?

[@MrDhainesh]

@@sennapparajan.p thanks for your response. Can show me roughly how to do program for 3 pumps control by 2 pressure switch. Its a cyclic operation. When ever duty pressure switch activate 1 pump should run and next cycle other pump should run. If 2 pressure switch activates means 2 pumps should cut in. Much appreciate if u give some idea on it.

[@sennapparajan.p]

@@MrDhainesh SURE WILL SHARE THE VID...

[@sennapparajan.p]

@@MrDhainesh kzbin.info/www/bejne/gaPLaX-saa6fjq8

[@MarkStaMaria-xu4tq]

Something is wrong. after 2 alternating cyclic, sequence is 1, 2, 3, 3 / 1, 2, 3, 3

[@sennapparajan.p]

send your program. will check [e-mail]