best video on the subject. do remember to account for the thickness of any scope lense covers you use.
@HeavyJ3183 жыл бұрын
Best scope mounting video ever!
@finney861 Жыл бұрын
Best video so far that I’ve seen on this. So simple. Thank you.
@artvanderlay77322 жыл бұрын
The lower the scope is great , but you have to take into consideration your comfort factor . If you are forced to get you head in an uncomfortable position on the stock you won't get the butt comfortable in your shoulder. Bad seating on your shoulder means you will notice recoil much more , plus not being able to brace your neck to your shoulder properly resulting in constantly worrying about being clouted by the scope . If you are not comfortable you won't shoot straight . I know this is all obvious but it is no good aiming for the lowest scope mount till you get the rifle comfortable on your body..
@alanrhonemedia2 жыл бұрын
Very good point and definitely a factor to consider. Thank you
@kouroshdavoudi7828 Жыл бұрын
Thank you for your tips, the only thing I would have considered would be the added thickness of the lens caps , I only know since it has happened to me.
@alanrhonemedia Жыл бұрын
Yes, a good and valid point. I might add this to the video description to accommodate for a lens cap or Bulter Creek if you use one, as these are normally 2-3mm. Thanks for the input.
@Huggybear1012 жыл бұрын
Great video. Been looking all over to figure out how to do this. Many thanks.
@gabrielkrivinko75643 жыл бұрын
Another thing you have to check on some rifles like the Remington 700 is the gap between the bolt handle and the scope. I dropped my scope down as far as it could go based on those measurements and my bolt would not function. So I got taller rings .
@alanrhonemedia3 жыл бұрын
Very good point. I can't alter the video, but I will add a point to the description. All the best!
@gabrielkrivinko75643 жыл бұрын
@@alanrhonemedia nothing wrong with your video, very informative.
@grahamholland79314 жыл бұрын
Good clear instructional video, I also went on your website, great range of mounts. Many thanks
@jeffkildow99176 ай бұрын
Thanks Dave! This was an excellent tutorial,
@tampa_sal Жыл бұрын
Great tutorial.
@Pygapascoe1604 ай бұрын
Excellent and precise information. Thanks.
@Raja_Chahal3 жыл бұрын
Best video have seen on height calculator
@garybalasa3158 Жыл бұрын
Very informative as usual, you do some great work👍
@Veton03Ай бұрын
Very simple and informative video. Thank you
@alanrhonemediaАй бұрын
Thank you for the comment 👍
@MrShelbyshane2 жыл бұрын
How much would a 20 moa drop a 56mm objective with a 34mm tube ? Thank you
@alanrhonemedia2 жыл бұрын
It depends on the length of the scope really. But I would tend to suggest the drop from 20mm on a typical scope, I would allow 2 to 3mm of drop. I hope that helps.
@MrShelbyshane2 жыл бұрын
@@alanrhonemedia yes it does , thank you 😁
@mr.noneyabidness3 жыл бұрын
That dang math everyone hates. Good work.
@darklight48153 жыл бұрын
very informative,thanks so much!
@troymeredith95283 жыл бұрын
So quick question,are most picatinni rails the same height or do they differ in height a lot.?.
@alanrhonemedia3 жыл бұрын
They do vary slightly depending on manufacturer. There are rifles with different heights for the front and rear bases, so a picatinny rail will compensate for this and one side of the rail will be thicker than the other. The height is usually measured off the higher base on the rifle and we tend to say this will be between 5 and 7mm.
@troymeredith95283 жыл бұрын
@@alanrhonemedia thanks for the information.
@egarciajr772 жыл бұрын
Very helpful
@TheCarolinacadmanOutdoors2 жыл бұрын
Great video, thanks for the info!
@w.t.pstandforyourlife.56393 жыл бұрын
Wow bro you’re a genius nice videos bro
@erick78622 жыл бұрын
thanks for this video, super! Does this calculation also consider the downward cant of the slope when you’re dialing to maximum elevation? Eg, if a scope has 100 moa of dial-able elevation?
@alanrhonemedia2 жыл бұрын
The method works for the scope body itself. So the scope body will not change position when you dial in any elevation within the scope, it's only the reticle inside the scope that changes. On the other hand, if you have mounts with built in MOA, which lifts the scope at the rear and effectively lowers the objective lens towards the barrel. This may have to be taken into consideration. For instance, we supply an adjustable MOA mount which adjusts from 0-70 MOA in increments of 10 MOA. We see an Objective Lens drop of approximately 5mm on some scopes when you adjust from 0 MOA to 70 MOA. I hope this makes sense and helps you out with your question.
@Jakhouseproductions4 жыл бұрын
Nice video. Thank you!
@alanrhonemedia4 жыл бұрын
Glad you liked it!
@ihorkrusynskyi66222 жыл бұрын
🇺🇦👍
@DD-gi6kx Жыл бұрын
stop saying mil, the unit of measure is not mil....its meters, the measure of length in the metric system is meters, mil is just an abbreviation that means 1/1000, in this case 30 mm or 30/1000 meters, the mil is meaningless by itself as you can have millimeters, milligrams, milliradians, milliseconds, milliamps, milliliters, millivolts ...there pretty simple isn't it
@alanrhonemedia Жыл бұрын
Thank you for the input. We will try to use the full term "millimetres" in future to avoid any possible confusion for our viewers. We've not had anyone question which measurement type we're referring to when we use the term mil before, when the context is clearly length in this case, but there's always a first time. I'm sorry if you, or anyone else, has tried to measure the distances in milliseconds or millivolts based on us using the term mil in the video. Sorry to ramble on and keep you, I'm sure there must be someone out there using the phrase PIN Number, that I'm sure you'll feel the need to correct. Or someone not using a capital letter at the start of their sentence, that needs an unnecessarily long explanation about the importance of using correct grammar.
@js-wq6zy10 ай бұрын
This might really only be of concern to that backward colony , the USA. The rest of the world uses and understands the metric system.@@alanrhonemedia
@whipLasch8 ай бұрын
@@alanrhonemediadon’t let the slow ones get to you mate, and don’t bother changing your phrasing to suit them. Everyone knows what mill means