SCREAMING EAGLE CAM PLATE AND TIMING INSTALL

I have an updated video coming out so go check it ....I F@#KED UP..
!!DO NOT INSTALL OIL PUMP ONTO CAM PLATE!!
2014 V-Twin Harley-Davidson Cam Plate and Cam Timing Alignment DIY Install.
The Gas Station brings valuable information one could use when working on similar project.
This is my 2014 FXDC 103" Dyna Im building mostly by myself.
In this video I show you the tools, torque specs and all necessary info needed when doing a Screaming Eagle cam plate install.
More oil, more flow, more horse power..
If you have any questions just ask, if i dont know i will refer you back to the 2013 Dyna user manual link here :
drive.google.c...
Contact info : [e-mail]

[@garygamble8477]

I hope you next video showed you installing the oil pump correctly. 1. Install well oiled oil pump into position 2. Install Cam Plate and torque all bolts. 3. Start but DO NOT torque 4 oil pump bolts. 3. Install chain, sprockets, etc. 4. Using a socket on crank sprocket bolt and plugs removed turn engine over several revolutions. 5. You should have very little turning resistance. This centers the oil pump over crankshaft. 6. Then torque the 4 oil pump bolts to specs. 7 Repeat step 2 and you should have no noticeable increase in turning torque. (NO PIPE WRENCH REQUIRED) 8. If so, STOP and figure out why!

[@TheGasStation1616]

Yeah I did the updated video after I broke myself off go watch it thanks for the reply

[@smiley4288]

Awesome video my friend, very useful as I’m in the process of amassing parts for my Dyna rebuild.... cheers fella 🤘😎🤘

[@TheGasStation1616]

Nooooooooo....!!!!!!!!noooo!!! Go watch the updated video, it's the one labeled danger

[@smiley4288]

@@TheGasStation1616 wow just watched the 1st few seconds of the 2nd one... thanks for that 👍👍👍👍👍👍😎

[@jamesonbutler9843]

Dude I don't trust shops. Just pulled mine open they put wrong pump in, guess what oil pressure was gone. Bad parts keep you coming back.

[@bigdaddysshop8180]

Too much music

[@billypeek7186]

yeah think ya did that incorrectly..pretty sure the oil pump goes in before the plate..and no assembly lube..c'mon man...and....

[@TheGasStation1616]

more then one way to do it but make sure the o-ring is not on male oil pump side or it will not seat correctly ..thanks for the comment..free manual for dyna in description

[@TheGasStation1616]

you were 100% right my oil pump busted like a dumb ass sorry..new updated video coming soon

[@billypeek7186]

@@TheGasStation1616 oh man sorry to hear that

[@h.d.m.c1669]

and what bearings did you use for pressing these shafts?

[@TheGasStation1616]

No shaft pressing but I did press new bearings for cams they are not located on cam plate but behind and they are timken..I did an updated video recently for the cam plate maybe watch that one..thanks for the reply tho..

[@LOVE-JC777]

@ 4:11 how can one go deep? Don’t bearing top out ?

[@TheGasStation1616]

I have an updated cam video this is wrongfully wrong and will fuck up your bike..the bearing does top out but you can push to hard and crack the small lip behind the bearing, you want to go far enough but not to far it's a feeling thing..

[@TheSkylark16]

Oh my, you're gonna be in trouble I can tell you that!

[@TheGasStation1616]

Watch my update video..lol yes you are right and yes it still works today after I destroyed that last oil pump..

[@jeffeberle6891]

Turn that shit off