Three things you should know about air assist（For SCULPFUN S10）| Air Assist | 10w Laser Engraver

[@NickSpirov]

I have a Sculpfun S9 with air assist add-on. Is it safe to turn off the compressor, when you have the air assist nozzle mounted? I thought that the laser lens will get dirty if there is no air blowing?

[@gurudataa1865]

Good day wanted to find out of the sculpfun csn cut through madf board..1/2 inch and 1/4 inch

[@upstatecre8]

Thank you for the video. I have an Xtool D1 pro 5wand I think the air assist will help out a lot with my cut times

[@SCULPFUNReal]

Try Sculpfun Next time🤣🤣

[@notthatcheeky]

can you please share your sittings on Lightburn with me? is there a video for it on the channel? my sittings are npt currect i think. I would really appreciate your help. Thanks 😊

[@pekingerleben]

I have the 5W laser in my sculpfun and I am very happy without the air assist. I never use 100 percent power to cut. With patience everything goes nicer. What about the 10w laser? Do I need the air assist for that or is it just recommended?

[@_chappie_]

I have a 10W from creality and its the same as you said, less power, more passes you can achieve just the same. I do have a fan blowing over my work desk though to help with ventilation.

[@privatebubba8876]

Air assist should be turn on when cutting wood. Air assist should be turned on low when engraving surfaces to keep the lens clean. So should air assist be cut on? Yes. Air assist should be on low when cutting acrylic.

[@floring480]

I will keep everytime the air asist on, it will keep the smoke away from the lens

[@MileyonDisney]

Thanks!

[@aadhithyanannamalai5177]

Will it cut gold sheet ? Stainless steel sheet ? Silver Sheet ? I am looking for my jewellery store

[@MECANOMATICCNC]

Corta y grava acrílico cristal?

[@iq0099]

You should have Air Assist trigger switch controlled by LightBurn from the software!

[@SCULPFUNReal]

Because the motherboard has not yet added this function, the air assist switch is by hand, we'll try

[@iq0099]

​@@SCULPFUNReal You should because we cannot wait long..

[@mirianpatricio]

@@SCULPFUNReal oi, minha sculpfun continua com o assistente aer em funcionamento ou seja vibrando quando o desativo no lightbour, é normal?

[@Dancopymus]

Your tips were very valid, but I have a question: in the third item, about engraving and cutting in the same file, you say to turn off the air pump when recording and turn it on when cutting, but in the LightBurn program there is a turn on function and turn off the air assistant on each layer. In that case it doesn't work? P.S. Do you have the Clock file to share? Thanks

[@SCULPFUNReal]

Because the motherboard has not yet added this function, the air assist switch is by hand, it is not controlled by software buttons, just displays or not display images for your watch. The clock file is ok, you can contact [e-mail]

[@WoWPro71]

@@SCULPFUNReal why did you do it so unpractical? It makes no sense when you need to cut and engrave a large amount of items at the same program. Is there any fix it this?

[@SCULPFUNReal]

@@WoWPro71 Yes, we need to work hard to overcome it, in the near future

[@dubbylabby6068]

It will require a relay controlled power plug (it could be added over the actual solution) switching on/off the full air assist pump. Extra point for hacking the pump air flow potentiometer and adjust the air flow at your needs… not so difficult at all but requires some tinkering and tooling for sure…

[@Dancopymus]

@@dubbylabby6068 Ok, thanks for the answer.

[@lucbra0754]

A minha deu problema com 3 meses de uso , menos de 15 horas de funcionamento, não recomendo !

[@barrymiller3609]

Ye I just tried cutting the exact test piece from the s10 kit with the same settings, does not cut. So guess money down the drain

[@thekuri2]

Thanks

[@humberto367]

Hi! a question do you from Sculpfun intend to implement the end of course? thanks

[@dubbylabby6068]

Run stoppers? These are easy to add if you have some basic iron soldering skills, time and will (I lack in the last :P )

[@mambaman2007]

Very helpful video indeed

[@carlosrios4203]

Hi,were i can buy s10 laser,im from colombia

[@SCULPFUNReal]

www.alibaba.com/product-detail/SCULPFUN-S10_1600519462568.html

[@carlosrios4203]

Hola,cuanto vale el envío a colombia,quiero comprar el láser s 10 también

[@SCULPFUNReal]

www.alibaba.com/product-detail/SCULPFUN-S10_1600519462568.html

[@carlosrogerioferreira7686]

Qual o programa que você está usando para programar

[@SCULPFUNReal]

Lightburn

[@dawnbreaker84]

A link to the wook would be nice as well :)

[@spoor4092]

I bought the s 10 model and it turned out not to work. I regret that I did not choose another manufacturer with affordable service and quality service. Money in the wind.

[@Sebasttan]

Jak to jest z tą mocą lasera. Na wszystkich grupach piszą żeby laserem diodowym nie ciąć mocą 100% a producent w swoich filmach jednak pokazuje że można. Jakie jest oficjalne zdanie producenta w tym temacie.

[@SCULPFUNReal]

When cutting thick materials, in order to improve efficiency, it is recommended to use full power; for thin materials, it is best to use 80% of the power; Working at full power will indeed have a slight impact on the life of the laser, and users can choose the appropriate power according to the usage.

[@Sebasttan]

@@SCULPFUNReal Dziękuję za odpowiedź. Pozdrawiam.

[@MrTattoom]

ola tem terste de gravação e corte para testar feito no programa que me possa enviar???

[@SCULPFUNReal]

You can contact [e-mail]

[@gulhal]

Guys beware of the SCAMMER seller 'Teach-Land Store' from Aliexpress. He is scammer and will sell u second hand products. Then if u want to return it, he will threaten u so u will write low value on the shipping so he wont pay tax. So he wants u to frauw with tax. Then if u says i wont do this, he blocks u and getting very arrogant.