Just wanted to alert everyone that this is not a blend motor assembly, which governs temperature regulation via blending hot and cold air. This is a mode motor assembly that governs which vents and/or windshield defroster air is being supplied to. Official Honda/Acura part name: Motor Assembly, Mode. Hope this helps.
@mrwendell4564 Жыл бұрын
Yes, he threw me off when he says door blender actuator. It's a door mode actuator. Not the blender
@Ihavethekenergy19 күн бұрын
So when he said "blend door selector", he was actually referring to the mode motor assembly?
@chorvang9670 Жыл бұрын
I just got done changing the actuator. The hardest part for me was getting the screw that you are trying to get out @7:58 out. What I did was drill a hold right on the metal pillar straight to the screw so I can use a small screwdriver to get that screw out. It turns out, my actuator wasn't dead, it was off of the white pin/part (whatever you call it). I changed it anyway. Thanks for the walkthrough taking off everything!!!
@alanmatthews9260 Жыл бұрын
Dang what did you use to make that hole? I tried a stepped metal drill bit but it didn’t go far at all
@alcerz984Ай бұрын
I just took my bottom tray out under the glove compartment hit the door actuator with a big wrench from underneath ( couldnt actually see it) but made it work again!!!!!! Worked like a charm. Hope this helps.
@neovang3 жыл бұрын
Thank you for this video. I had the same problem and after replacing the actuator, it works.
@jdawgl332 жыл бұрын
Great video! I took apart my driver’s side air mixer. Greased it and we’ll see how long it holds up. Same as passenger afaik, but easier to access.
@alltsab2 жыл бұрын
Thanks
@suncitycards915 Жыл бұрын
This is exactly what’s going on with my car. Thank you for making this video.
@alltsab Жыл бұрын
You welcome
@chauncymax3 жыл бұрын
You have to have the patience of Jobe to attempt this. I will pay the$220 to have a mechanic bust his knuckles. But thank you. I watched the whole thing. Very suspenseful
@scotthayden6752 жыл бұрын
Thanks for the video, it was really helpful! I was hampered by an out of spec glide pin on the replacement actuator. I ended up swapping the track/pin assembly between the old and new part and it fixed my issue. Works great now!
@alltsab2 жыл бұрын
Good job man
@JA-qg7se11 ай бұрын
🎉
@JA-qg7se11 ай бұрын
😢 0:32 😢🎉😢
@Sergio.4933 жыл бұрын
I really want to change of mechanic your good at your job👍👍
@barbararodriguez54312 жыл бұрын
Thanks for this video hope my husband can see it and hopefully fix the problem. Thank you so much
@alltsab2 жыл бұрын
You welcome
@ralphhoutz22852 жыл бұрын
thank you for the video saved me alot of time.
@alltsab2 жыл бұрын
You welcome ☺
@SunnySingh-dd4ez11 ай бұрын
thanks for your help brother my was doing the same thing all I did was hit it with a screwdriver and it started working again. Thanks again
@alltsab11 ай бұрын
You welcome
@melvinvasquez-gomez279710 ай бұрын
how hard did you have to hit it? might try that first thing tomorrow. Did you have the car off when you did it or was it on with the air on?
@manuelquesada78002 жыл бұрын
Thank you for that helpful video keep doing this info videos to help other people
@alltsab2 жыл бұрын
Thanks
@albertofigueroa7081 Жыл бұрын
Thanks for the video it help me a lot, The part is: (blend door actuator) for honda pilot, and is the same for model from 2005 to 2015 on amazon for $30
@alltsab Жыл бұрын
Thanks
@gregmears3401 Жыл бұрын
Great Video... Mounting the motor is no charm either. I did not buy a motor, but decide to see if I could get it to work, these motors are not cheap. The tabs break easily if you are not careful and I did break a few, but as long as most of them are ok you should be good. Remember that the motor is getting mounted with 3 screws to keep it together. So, when you get it open, you will see one big gear and metal prongs to the connector. Mine had a alot of grease on them and the big gear surface. I wiped them off and the gear surface where there is metal plating. Leave any grease on the gear. with that done put the metal surce of the gear on the prongs and put the housing back together. If that is the cause, the motor will rotate once you connect the harness and the motor together and start the Pilot and run through the modes on the console. If the motor rotates then you are good, once you turn off the climate system the motor will rotate to a default state. You should be good to go and mount which takes awhile since it is buried, I used a towel to press against the motor housing and metal bracket until I could get one of the screws fully in. At least on my 2010 Touring Pilot, I was able to get to all the screws without taking out the bottom vent.
@ez2njoi1233 жыл бұрын
Thank you. I know I can not do it myself but good to know.
@10643613 жыл бұрын
It used same actuator for both center vent or it had 2 actuators?. My pilot does not blow air in any just in the two on the sides.
@ronone62232 жыл бұрын
Thank you much for helping 👍🏻
@alltsab2 жыл бұрын
You welcome
@vitaliknebuterin9277 Жыл бұрын
Thanks! Subscribed!
@alltsab Жыл бұрын
Thank you for your help subscribe
@yosmarvillafana24093 жыл бұрын
Is this the same spot for a 2012 Honda Pilot
@hedy_70847 ай бұрын
My front vents blow regardless of which mode I switch to. Would this be the repair I need to do? Thanks!
@warrenmontgomery5063 жыл бұрын
What a pain in the butt. Thank you for making this video as I have to do the same the my wife's car.
@sarvidec2 жыл бұрын
What is the Honda part number for this?
@edwardkareem6446 Жыл бұрын
Thank you Honda for not making this so difficult some vehicles like Nissan you required to take out the whole dash
@alltsab Жыл бұрын
Your welcome
@stephenbrunner4823 жыл бұрын
Thank you for the video. But, after I aligned the lever, I cant get the pin and slot in the lever to the places on t he AC unit prior to putting the screws back in. CAn you show that?
@alltsab3 жыл бұрын
You have to turn the new one to match the old to be exact fit
@jerwind7393 Жыл бұрын
Nice video! Thanks for sharing! We have a 2009 Honda Pilot and the center AC vents stopped working. The Driver, Passenger and back and rear AC works and blows out fine. I've been searching and searching and couldn't find the cause and resolution to fix the center AC vents to work again. Tried also adjusting speed and mode back and forth and same results and no blowing in center AC vents Any help or suggestion is greatly appreciated. Thanks in advanced!
@thomasbrown59456 ай бұрын
I have the same issue with my 09 the issue is the part being replaced in the video, I took mine apart and applied a little pressure to the white plastic arm and it started moving again not sure if it's going to get stuck again if so I'll just replace it
@thomasbrown59456 ай бұрын
I did this while cycling through the modes I didn't take it out
@JavierPerez-co7sc11 ай бұрын
I’m having the same issue on my 2011 Honda Pilot EXL. I will be driving then all of a sudden my front center vents will stop blowing air. The drive Lh side and passenger rh side and the rear vents will still work but the front centers stop. They turn back on whenever they want
@dennisdivine74484 ай бұрын
I have the same problem on the identical vehicle (2011 Pilot EX-L). I've learned that it may take several weeks for the middle air condiitioning vents to come on during the summer, & when they do start working, don't turn the air off!
@rakeshrai5792 жыл бұрын
Thanks for the video, What is the part number for this actuator for honda pilot 2011?
@rakeshrai5792 жыл бұрын
after reading the comments, I found out : Part number is 604-868
@ricowork3 жыл бұрын
I have the same problem on my 2009 pilot. Is it the same location? Thank you.
@ricowork3 жыл бұрын
On second thought, it seems very complicated for a beginner KZbin mechanic like myself :-)
@alltsab3 жыл бұрын
Yes the same
@gilbertocaldera10413 жыл бұрын
Hi Is this consider left or right actuator? Because I was told there is two left and right
@alltsab3 жыл бұрын
Passenger side
@gilbertocaldera10413 жыл бұрын
@@alltsab great thank you
@nowherejoe13682 жыл бұрын
Hello, what is the tool you were using to get the screws out? I need detailed information about what to use to get the motor out. Thanks
@alltsab2 жыл бұрын
Screw driver
@nowherejoe13682 жыл бұрын
@@alltsab the ratchet thing, what is it called? what should i buy to get the screws out
@alltsab2 жыл бұрын
@@nowherejoe1368 no just a convenient thing. 8mm 1/4 inch swivel sockets will small 1/4 rachet.
@nowherejoe13682 жыл бұрын
@@alltsab I tried the swivel thing and it wouldn't fit on that top screw cause of the metal bracket in the way
@nowherejoe13682 жыл бұрын
also your swivel seems to go into a 45 degree angle the one I had did not
@albertoardon11473 жыл бұрын
What is the numbering of the part that you changed? I have the same problem.
@alltsab3 жыл бұрын
Sorry I forgot to film the part so I don't remember it but if you go to auto part ask for actuator blend door they should be able to get you the correct one.
@RAMTRPR2 жыл бұрын
Dorman 604-868 HVAC Blend Door Actuator for Select Acura/Honda Models
@mariomadonado36162 жыл бұрын
@@RAMTRPR thanks and thats for a 2011?
@mariomadonado36162 жыл бұрын
@@RAMTRPR thanks
@Hoodbane2 жыл бұрын
So what’s the correct name to search the part up ?
@alltsab2 жыл бұрын
Actuator if you like to get the part number you may have to take the old one out and get the number from it
@MrJewelicious3 жыл бұрын
how many actuator does it have? do you have the part number?
@alltsab3 жыл бұрын
I don't have the part number. I think it have 3 actuators
@MrJewelicious3 жыл бұрын
@@alltsab My driver side vents only blows warm air when AC is on. Cold air comes out from the passenger side and rear passenger vents. do you know which actuator i need to replace?
@alltsab3 жыл бұрын
@@MrJewelicious you need to add more freeon I have another video on the toyota avalon explains about. I believe your actuator is good add about 8 to 12 oz freeon should solve your problem.
@alltsab3 жыл бұрын
@@MrJewelicious please help me subscribe 👌
@mariomadonado36162 жыл бұрын
DO YOU HAVE THE PART # GOOD VIDEO
@alltsab2 жыл бұрын
No I don't have it.
@yosmarvillafana24093 жыл бұрын
I changed this part but for some reason now the floor vents don’t come out
@alltsab3 жыл бұрын
That mean the setting when you put in may be wrong so it doesn't turn all the way to the floor
@aestheticroyales9937 Жыл бұрын
You have to engage both tracks in the white piece
@kaiyuenkong19552 жыл бұрын
Thank you for the video. I just did this yesterday. After I was done, it would blow towards me, but when I switch modes to blow up, or floor, or anything it would still blow towards me. I see the actuator moving though. Only when I use the defrost button it switched. Other than that only blow towards me works now. Any ideas?
@alltsab2 жыл бұрын
Probably you put in the wrong position you have to take it out and realign it so it can be work properly
@kaiyuenkong19552 жыл бұрын
@@alltsab No, I matched it up. I plugged the new one in so it would go to the position of the old one.
@alltsab2 жыл бұрын
@@kaiyuenkong1955 possible you control is bad. Did you plug the new one and turn your selector knob to test the movement before installing. There are 2 actuator located closed to each other you may replace the wrong one. I suggest you take it apart and turn your ac knob or vent selector know to see it move. If doesn't move that mean it could me blown fuses or the ac climate control unit is bad. Good luck buddy
@alltsab2 жыл бұрын
Please help me subscribe to my channel ok I need your help too 🙏 ❤
@kaiyuenkong19552 жыл бұрын
@@alltsab I subscribed, thank you. I ended up taking the actuator out again. Manually moving the positions. Found the position that matched the blow mode. Reinstalled. Everything works now. Thank you.
@donnyjauregui31512 жыл бұрын
How I do Calibrate the actuator ?
@alltsab2 жыл бұрын
You can plug it in and turn the nob to align as the old one before you install it.
@donnyjauregui31512 жыл бұрын
@@alltsab is very hard and I don’t want to break it do I need to start the car first, btw how do you turn it cuz can’t do by hands is very hard
@alltsab2 жыл бұрын
@@donnyjauregui3151 plug in the actuator then turn ignition to on position then turn your nob selector
@dewholdingsllc10502 жыл бұрын
Mode door actuator, is bad not door blend that is for hot cold
@inclementmikep593 жыл бұрын
Never ever plug them in and move them without them being installed. The motor will strip. Just turn the door by hand to match the gear in the motor. Much wasier
@sibeles2 жыл бұрын
Hi, can you share the actuator part number.
@SamLopez11 Жыл бұрын
should be 79140-SHJ-A01
@grae_sea3 жыл бұрын
yEe hAw
@victer7022 жыл бұрын
did everything but cant switch to floor vents blower
@alltsab2 жыл бұрын
Maybe your setting the actuator wrong position.
@aestheticroyales9937 Жыл бұрын
You have to engage both tracks for floor vest and top vents