One would think Honda and Denso would know this from the start. Our cousins, "down-under", fix, instead of replace, all the time. Entertaining and informative! Thanks!
@guillermomorbelli2005 Жыл бұрын
Just saved a lot of money and made me look like a hero at home. Thanks for sharing. I did the top one (closer to the roof) to fix vent/defrost/floor direction motor. In this case you need to ensure the two handles fall back into track. You can do this with your hand while pressing the direction button. Also 7 long socket seems the best way to remove three screws after removing 3 “boxes” on top to clear way with a 10 socket. Also make sure you mark the position of the motor so you don’t put it back with inverted polarity.
@woodstockMaxQ10 ай бұрын
Thank you for the additional info. My service manual calls it a "Front Mode Control Motor" which actuates the "Air Mix Door". I'm going to go take mine apart now....
@guillermomorbelli200510 ай бұрын
@@woodstockMaxQshould be very straight forward. I had to remove some things from the way to have some room. Also make sure you try it before screwing it back up there by connecting the cables and pressing the buttons.
@woodstockMaxQ10 ай бұрын
@@guillermomorbelli2005 Done! And..... it works! I didn't have any issues. Just cleaned off the contacts and put it back together. I do wonder about the grease though. Dielectric grease should be fine to have on the contacts. Mine was pretty dirty, so if it actually was electrical grease, then all that dirt must have made it conductive. Thanks again for the info from OP and you!
@derrickbarker83542 жыл бұрын
Wow, thanks for sharing this is what I needed for my 2013 Honda Odyssey
@Sirrehpotsirch2 жыл бұрын
Ugh! That is dialectic grease. It is supposed to be there. Also, the position of that white actuator arm are doesn't matter. Wiping the contact points removed some tarnish or debris that improved the electrical contacts.
@briondaniels845111 ай бұрын
Exactly!!! That is dielectric grease to prevent future oxidation. It is okay to remove it to clean any debris out, but it is wise to reapply a new layer of grease and you should be good to go.
@noahpavey65042 жыл бұрын
Cleaning the contacts and resistive strip with Deoxit fixed mine right up. Thanks for the video!! Saved me a $100 part
@woodstockMaxQ10 ай бұрын
Thank you for doing this video! FYI - Nomenclature from my service manual: The part you removed is called a "Driver's Air Mix"Control Motor". The one above it is called a "Front Mode Control Motor".
@BeZRules9 ай бұрын
it also called door blender actuator
@jimmyhotel8061 Жыл бұрын
Ok boss great video saved me $ and driving in the desert heat. Thanks for posting! I subbed!
@BeZRules9 ай бұрын
have honda pilote and facing the same issue , looks like this issue with all hondas in that generation and that part new is about 180 usd not cheap , thanks for the video ,
@ryantaylor81872 жыл бұрын
Nice fix. I'd recommend a 7mm socket next time.
@18tito2 жыл бұрын
I used a 7 mm deep socket and it was a lot less of a hustle
@knfpumps Жыл бұрын
I cut out some 3/8" square cardboard squares and threaded the screws thru the mounting hole into a hole in the cardboard to hold the screws in the holes.
@dignopadron3722 жыл бұрын
Good video.
@LucasGarrow Жыл бұрын
Any idea how to clear the B1235 code after repair? actuator is working, thanks for the walk through
@scowell Жыл бұрын
That... was an ordeal. Get a 7mm swivel socket or 1/4" hex flex extension.
@lorenzohuamanchay73909 ай бұрын
💪 Good Job.
@saltydecimator Жыл бұрын
Does this fox if I’m not getting any air on drivers feetz? Mine doesn’t move nearly That much either, around the 25:30 Mark etc
@auntkrusty Жыл бұрын
Can you give me an update on if this fix is still working a year later? Just removing the excess grease still working?
@glongshot2 жыл бұрын
How did you remove the plastic cover from the beginning?
@charlesetheridge9380 Жыл бұрын
U r my hero u got 3 hands lol
@Forzamilan228 ай бұрын
please somebody help me. is the white bit supposed to move? is that the reason why my heating doesn't work? my one is stuck, i ordered another one (used) but it also have the white arm stuck
@georgearnett-atlantatreepr72142 жыл бұрын
Great share!
@gravedigger6967 Жыл бұрын
my blend door actuator is working fine. But my driver side is blowing cold even though i turned up the heat 🥶 n passenger side is working fine? What do you think is the problem?
@PaboosFam Жыл бұрын
There are 2 actuators under the drivers side I think. Try the other one.
@gravedigger6967 Жыл бұрын
@@PaboosFam Ok. Thank you. Is it the one above the first one?
@guillermomorbelli2005 Жыл бұрын
@@gravedigger6967 it is the lower one. Closet to the floor.