Secrets Of The Profile Pipe! WHY DON'T WELDERS TALK ABOUT IT?

Wow! Welders will be shocked!
Friends, my name is Sergey! I am the author of the channel HandiCrafts.
On this channel I present everything that I have done with my own hands.
Creative ideas, useful tips !
We turn simple things into unique ones! Subscribe, it will be interesting! #craft #wood #diy

[@hgsto]

Very nice.. Felicitaciones

[@samukacapitao1608]

great. simple and eficient. I will start doing like that. thanks for the idea

[@titojac2007]

👍👏👏👏 Vc é um profissional...

[@ismiravel3197]

Parabéns excelente técnica.

[@moyejasguzquin4695]

Excelente

[@juanalbertoalvaradosantana7900]

Hola para hacer ese tipo de corte, cuantos milimetros le quitas para que te quede de la medida que quieres ya que al doblarlo te aumenta unos milímetros

[@nathanblanchet2648]

Useful technique for me to try with my everlast welder the next time I use it.

[@user-xy4pk9dg7o]

感谢分享。

[@wilbury88]

You do not talk too, only shows what you do, but thanks for sharing your knowledge!

[@brggmc]

If you're going to weld up a tightly closed joint, penetration will be very poor, with no strength when it is cleaned off. There should be a slight gap between the two edges to be welded, allowing the weld-pool to melt through the thickness of the metal to the bottom face, thus amalgamating the whole piece into one. The only time butted-up edges would be acceptable is on very thin steel (sub 2mm), when it is relatively easy to use enough amps to safely create a good solid through-weld. A 'hotter' shielding gas might also help, to prevent early cooling of the weld-pool.

[@MrRedgenator]

In my personal opinion, this can be done with anything smaller than 1'4 inch thickness, if you have a half decent welder, you can penetrate all the way through. 2. On the topic of the Video, I choose to simply spent a total of 2 minutes on the BANDSAW and miter my cuts at 45 there. I do not eat up half a cutoff wheel notching each corner, there's 3 notches per square, that adds up. And because the fitup may not be a true 45, and you might have to grind more, or less, and if you notch incorrectly, you are filling a gap. It's less efficient imo

[@b.p.rwebber8098]

I agree I adjust the clamp on my cut off saw to 45, the thing I like with this idea is no weld required on the outside corner .

[@sabrosizzimo]

Muy bueno , saludos

[@rokolozano9961]

Very good solution for curved cuts, good luck!

[@egbertomiranda4931]

100% maravilhoso gostei de mais show

[@tehnikmesin]

kzbin.info/www/bejne/fHyslWh5jLajZrM Monggo lur belajar bareng. Jgn lupa dukungannya

[@praptonugrohost8766]

Mantap Bang, rahasia atau nggak, yang penting ditonton 1 juta lebih......MakDOOOR Joss Gantos

[@dylanialith6333]

Grand merci ca va beaucoup m'aider 👍👍👍

[@alaincaron4665]

Bonsoir connais tu le nom de se procéder

[@anubis4611]

Me aclaraste muy bien el por qué me quedaban mal.eres genial, gracias

Hola amigo estoy creando videos de herrería te agradecería mucho 🙏 si me pudieras apoyas suscribiendote a mi canal de KZbin de antemano muchas gracias 😊

[@iconmoto7745]

Anung tamng sukt sir kpg ganyan .45 dgrs b yn png gate.slmt.poh

[@eribertosoares4666]

Genial!

Hola amigo estoy creando videos de herrería te agradecería mucho 🙏 si me pudieras apoyas suscribiendote a mi canal de KZbin de antemano muchas gracias 😊

[@roseberlinelouis4325]

Que bueno!!! 👋👋👋

Hola amigo estoy creando videos de herrería te agradecería mucho 🙏 si me pudieras apoyas suscribiendote a mi canal de KZbin de antemano muchas gracias 😊

[@podomorosteel9870]

you are truly smart, continue your work so that many can be helped

[@jesoniascosmodelima2141]

Perfeito , parabéns pela explicação

[@candlecamargo2274]

kkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkk

[@candlecamargo2274]

pior q eu ri pq eu não entendi o que mudou medindo a espessura auhauhhaauhauaha

[@mariocopete5932]

Gracias

[@marliribeiro4142]

Sensacional 👏👏

[@princestevens1197]

Wonderful

[@d3n1.s]

Thanks bro👍

Hola amigo estoy creando videos de herrería te agradecería mucho 🙏 si me pudieras apoyas suscribiendote a mi canal de KZbin de antemano muchas gracias 😊

[@Ronja_Roevardotter-SE]

Super Video, ich habe viel gelernt.

[@migeldavalos1348]

Grasias por el video he aprendido varias cosas...

[@muchdarofficial1936]

Mantap bang jos

[@smarthumans751]

amazing... thank for sharing

[@carlosderezende2946]

muito bom. vc mostrou o errado e depois o certo sem blá blá blá. na prática.

muito bom

[@dangvanhoa41]

Rất hữu ích

[@jujupi8078]

Cảm ơn anh đã trình diễn. Chúc anh có sức khỏe tốt, vui vẻ và hạnh phúc

[@JuanSoto-to2lb]

La soldadura hasta donde yo entiendo debe tener una separación dependiendo del grosor del electorado que vas a usar .Para asegurar la penetración y la resistencia del cordón

[@ivancanseco6223]

Así es, por eso en las tuberías se tiene que aplicar la técnica de biselado para que logre aherirse

[@b.p.rwebber8098]

@@ivancanseco6223 on 2mm steel the join would be enough to allow the weld to penetrate as long as the technique is right.

[@hanturimba171]

Mksih ilmunya brow

[@NonameNoorg]

easy but genius 👍

[@criticofred8195]

desde el punto de vista mecánico hay mucha sobrecarga en el doblez, mejor es soldadura alrededor de 2 piezas unidas a 45°

Hola amigo estoy creando videos de herrería te agradecería mucho 🙏 si me pudieras apoyas suscribiendote a mi canal de KZbin de antemano muchas gracias 😊

[@beimararce3339]

Y que opinas si fuera en perfil en c

[@rubenayla]

La soldadura es más resistente que el doblez? Pensaba que con acero dúctil se endurece pero aún aguanta mucha deformación

[@alexsanderjoseabad1722]

Muy bonito pero se desperdicia material. Al hacer el corte 45 completo el otro corte te sirve sin desperdicio de material

[@orxanhesenov7346]

👍👍👍excellent

[@Jpgundarun]

The one with the slight gap will have a better penetrating weld so what's the problem?

[@user-vk9io1lv6r]

大変勉強になりました　有難うございました

[@shuminoheya]

素晴らしい！！もう少し早く、この動画に出会っていれば。。。

[@vagnerives]

Muito bom 😃

[@user-co2tn8dp2o]

PERFECT ! BRAVO !

[@gummalasamba2261]

Super trikce

[@nivaldofernandes2702]

Show . Obrigado .... Resolveu minha dificuldade ....

[@massimilianozafaro1688]

Ciao Io qualche annetto ho saldato e volevo dirti che sinceramente nel secondo caso il taglio e' ben eseguito ma quando andrai a molare le superfici dopo averle saldate , proprio perche' cosi precise della saldatura restera' molto poco e al primo colpo potrebbe innescarsi una cricca , se poi capita dopo la verniciatura e' ancora piu' fastidioso . Se invece lasci un po sulle giunzioni un po di cianfrino allora la saldatura penetra e quando vai a molare comunque qualcosa rimane nel cianfrino e rende la saldatura piu' stabile...

[@pkfamily2199]

ฝีมือดีมากครับ

[@chablogregalla7259]

Wow nice idea

[@mytube3687]

Thanks 🙏 for sharing this is what I was looking for.

[@user-ik7ye4tq6q]

تبارك الله عليك

[@naufalramadhan2850]

Ternyata selama ini saya salah, terimakasih infonya bermanfaat sekali

[@akbaryusuf559]

yang bener kaya gimana harusnya., saya gak paham video nya

[@karaah224]

Awesome

[@sonuansari33]

Cool

[@umelec-diy]

Классно!

[@openclose93]

I like it your perfect ideas...thanks

[@kabecraft1223]

Mucho trabajo de más

[@analiacomas4340]

Esta mostrando que el vértice de los ángulos lo marca respetando el espesor del perfil? O que además hay un espesor de los separa?

[@luisjose8062]

exacto respeta el espesor del perfil por eso utiliza el berniel...saludos.

[@JATIGARSI]

Full nyikuu

[@erandadamith451]

very good bro

[@diegoperezchavez3989]

Resumen: Los ángulos de corte, deben nacer luego de haber considerado el espesor del perfil. Gracias.

[@jasonkay5092]

Welders dont talk about it because cutting it on a 45 and welding it is a lot better than this

[@alinmihaistoicescu6821]

if you have only 4 corners to weld and you are not a very skilled welder this is an easy way in my opinion. Better to spend half hour to prep your weld than 3 hours to fix a twisted bar. If you just cut 2 pieces of pipe at 45deg and you weld them if you don't have the right tools to align them (welding magnets, square magnets etc.) and if you are "occasional" welder there is a big chance some may get a shitty weld and/or twisted bars.

[@jasonkay5092]

@@alinmihaistoicescu6821 if they had the time to commit to buying a welder there is no excuse that somebody did not go out and not get magnets, squares and so on.

[@victorgasman4357]

Pliz I need to know how to cut zed bar make a video

[@user-mk5yf5gx2n]

อ่อแบบนี้นี่เองว่าละทำไม45'มันเข้ากันไม่สนิท

[@user-qv7rx6lv2z]

Nic💖💖💖

[@muhammadarif4715]

Useful technique for me

[@dineshgovekar8349]

Very nice

[@jesuslara6533]

Min 1:53 For those who ask where's the secret. Notice the mark at the bottom.. Para queens preguntan por el secreto. Fíjense en la linea de abajo. Marca el grosor de la lamina.

[@ArdimanKhiar]

That vag 1 n 4

[@user-wp6rc1jw1z]

Все правильно , геометрия наука точная.

[@paulistrate8488]

Very good , show us how to cut 125°

[@naeemgillwelders985]

Good bro

[@candlecamargo2274]

alguem poderia me explicar o q realmente mudou depois de medir a espessura da chapa?

[@TuanTran-qo2cf]

🤩🤩🤩🤩🤩

[@khalilkhan7240]

100% .✔

[@ririnreka9524]

👍👍

[@-akramkamel9021]

👍👍👍👍

[@krystian7589]

Mozna tez tak zagiac rure ?

[@supriadi7769]

Bkin 1 sdut aj abis waktu brfa lama om

[@krushalghanekar4278]

छान

[@andilong6977]

Hello, are you using cut off tool or angle grinder?

[@ugikprs]

Mantul

[@mariandumitru5828]

Explica exact cum faci măsurătorile Se vede cum măsori cum debitezi cu flexul dar spune cati cm sau mm se masoara pt acel unghi de 90

[@alinmihaistoicescu6821]

Nu masoara, foloseste echerul. Echerul are clar unghi de 90 nu? iar daca te uiti atent banda galbena intra in manerul echerului fix la 45. Pur si simplu alege punctul de unde vrea sa indoaie rectangulara si trage cu echerul 2 linii la 45. Dupa care verifica cu echerul pe interior sa fie perfect 90.

[@Philipusxviperr]

Good job!

[@MrToyotacorsa]

Hallo natürlich ist das mit dem grünen Harken FAST richtig weil man muss die Schenkelseiten noch anfasen damit man mehr Fläche hat zum verschweißen so einfach neh

[@michaelmoody5383]

Cant believe you've given our secrets away 😂😂

[@SyauqiDeChannel]

Nice

[@olanmaksalud8802]

อ้อ! เว้นใว้เท่าความหนาของเหล็ก ไช่ไหมครับ

[@josecaterc]

ya con esa escuadra de carpintero no es serio para un aprendiz como voz esta bien pero la escuadra de un herrero profecional es diferente

[@elidiosantos9925]

👍👏👏

[@ppawel7557]

Ślusarz trasuje rysikiem, stolarz ołówkiem, a fuszer mazakiem. I tyle w temacie.

[@mihaela255]

Daca țeava nu este suficient de lunga că sa o îndoi, cum procedezi? Faci colțul și sudezi o prelungire?

[@nhyilmaz8115]

Maaşallah gardas

[@toolsandcrafts]

amazing

[@SaulSaucedoSS]

kzbin.info/www/bejne/iHjEhWmHep16aMU

[@tomthompson7400]

once you see a claw hammer you can guess what type of metal worker your watching ,,, and it wasnt disappointing.

[@mdroton111]

nice

[@cesararmas2651]

Con todo respeto, pero explique el procedimiento, o es video a lo antiguo, cine mudo.

[@1288832]

Пилу еще не придумали у вас там?:)

[@isaiasfreitas1]

Qual a medida dos cortes?

[@ju38g]

Parce que un soudeur coupe 2x 45 et soude ^^' c'est une perte de temps de tracer et couper a la disqueuse !

[@endangkur5236]

Rapih sih tapi lama itu MH bos proses nya

[@RoderyJose]

tubo cuadrado de 3/4 y esta en un Angulo de 45° ????