Setting Throttle Position Sensor for 22RE

[@keithsutton100]

Found your video after I figured it out too. I think you are exactly right to do test #3 first get the infinity ohms by rotating the TPS body. After that all the other readings worked

[@lori4931]

This really helped my husband. There isn't much he can't figure out on his beloved truck so thank you for doing this, Jim!

[@tubejim101]

Your welcome :)

[@Wildspirit2016]

Helped me out a lot! Put in a brand new TPS and still revving at 3500rpm at 90kms/hr( 55 MPH). Thank you for the video

[@trevordarnell673]

I have waited on this exact video for years, omg thank you so much!!!

[@tubejim101]

Your welcome :)

[@trevordarnell673]

tubejim101 👍👌🤟✊😁

[@flakdawg]

I tried this test as well. Good that you did a vid on it. I also agree that the #3 test should have been the first test then proceed with the remaining test. I did the same with the clips and they help alot. Keeps your hands free to adjust the TPS and throttle. Great vid.

[@snippits75]

Thanks for the video! I am sure this will help a lot of people. It's easier to adjust it when the throttle body is on the bench. The two TPS adjusting screws are hard to get to with a screwdriver when the throttle body is mounted. Harbor Freight sells an eight piece right angle screwdriver set that will make it easier to adjust the TPS when the throttle body is mounted.

[@tubejim101]

Thank you.

[@reinaldogonzalez6045]

snippits75 : what you saw in the video is not adjustment, that is to verify that the tps is in good condition.

[@twiz8789]

Those Vessels are AWESOME!! Love it

[@tubejim101]

Yep. Love mine :)

[@korysteffen5189]

Thankx a lot man out of 10 clips I didn't understand a thing until you cam along

[@anthonyonate6268]

Thanks for the info bud hope your haveing a good day 4 real thanks again man🎉

[@gatzbravo]

This helped me a lot and I have a suggestion that people can also use to use the probes on the tiny terminals. Anyway you can make a lead wire with a spade female terminal that is normally used for speaker wires. One reference u could use are the two small speakers by the glove box and left to the steering wheel . Those wires have the same connectors that fit perfectly on the pins. Also I happened to have a push button switch plug that I was going to use to activate the horn and broke the plastic housing off to get access to the wire and connectors, just a last minute kinda thing . Also if you have a downward pointing TPS orientation type like mentioned on the type up from crawler , there’s not alot room for error I found with the recommended oem parts . I had one that I purchased online and it was orientated downward but it took alot to test and get the proper readings . I’m sure there might be more to it from vehicle to vehicle and wear and tear . I’m interested if anyone else had the same experience

[@gatzbravo]

With that suggestion I’m looking for one also . I removed the upper intake manifold to clean it and buttoned everything back and as soon as I energized the fuel pump gas leaked from the cold start union bolt where the copper crush washers are. Do these need to be replaced each time the banjo bolts are removed?

[@tubejim101]

@@gatzbravo Yes.

[@probablyhomer9338]

Good video. Makes sense. I got code 7 and 11 which says bad tps or ecu. Going to try this and see if it helps. Maybe out of adjustment.

[@donaldgarin1938]

Would have been nice to see ya show the meter reading when you made the adjustment but it is a good vid

[@alexandergonzalez2232]

Hello Tubejim, toyota corolla 2000. I did not see you open throttle and close the throttle for reading in ohms. My grd wire 0.1v; signal wire 12.36; 5v reference wire 1.67v. I back probed all 3 wire while opening and closing throttle flap 0 response on throttle resistor. Disconnected the connector ohmed the ground and the signal wire middle ohm reading is 1.814 ohms. open/close throttle ohm stayed the same. What I learned from is how to make adjustments to the flap. If you can tell me is this a defective throttle it would help me . Respectfully, AG

[@tubejim101]

I only know how to do this for the 22RE engine.

[@alexandergonzalez2232]

@@tubejim101 thank you I did learn from about adjusting throttle and the variebles I will encounter when I replace mine throttle.

[@karlnorman4193]

Hi, great video. I am going to remove/clean TB and adjust TPS regardless, but I thought I'd ask a theoretical question to see what you might think. So I am getting a lean fuel mixture causing pinging/knocking and I have eliminated other causes but not all...yet. My question is do you think an improperly adjusted TPS (Assuming all other air ,throttle, injectors, etc are set and working correctly) could cause the ECM to interpret a lower throttle position and therefore result in less fuel being injected causing a lean mixture?

[@tubejim101]

TPS being off is going to cause your engine to not get the correct fuel. If your getting pining/knock, I would suspect your knock sensor. Also check your timing if your getting ping/knock.

[@karlnorman4193]

I have been checking many things but so far no luck. Thank you for the reply. TB and TPS is next when I get the time. Thanks again.

[@stevejette2329]

KARL - "Great video "?? Terrible camera work and going back to say "this probably should have been step #1" ?? Try a little preparation before taping ?

[@tubejim101]

@@stevejette2329 You are correct. Terrible camera work and lack of editing. If the message got across, I am lucky.

[@mpless100]

Good info. Thank you

[@rayhughes1974]

Brillaint info huge help , thank you!

[@michaelspong2056]

So this can be done totally on the bench? I thought it would need power going to it while installed. Thx. I was hoping for Acknowledgement it can be done on the bench, but appreciate the thanks. Mike

[@tubejim101]

Your welcome :)

[@bringmethehorizon129]

Don’t need power to check resistance

[@bpeterson1995]

No the tps sensor is basically a rotating resistance sensor

[@stevejette2329]

SO much good info !! Wish it was a little more organized/ prepared …

[@AG-rx1bo]

Thanks. Very helpful.

[@douglasvaughn9349]

Hey Jim great video . Here’s what’s going on with my 1991 Toyota Pickup . It will start up and idle. As soon as you give it gas it Boggs down and dies. I can drive it down the road and as long as the gas peddle doesnt go down all the way it’s fine. So I checked the engine codes and it said that is was tps. Went and bought one and it wouldn’t even start up . Took the new one off and put the old one back on and it starts but again same problem. I’m confused . Any help?

[@tubejim101]

Setting the TPS is something you will have to do, even if you buy a new one. After you set the TPS, check/set your timing. If you have the 22re, you will set the timing at the 5 mark.

[@douglasvaughn9349]

tubejim101 so it still could be a bad tps I just installed the new one incorrectly?

[@tubejim101]

Yes. Installing it easy. Setting it is tricky. If you set the infinite ohms first, most likely, everything else will be set too.

[@douglasvaughn9349]

tubejim101 so I assume my original is bad? Even though it idles?

[@tubejim101]

If the ohms are out of range, at the different feeler gauge settings, then it is bad. The TPS changes the ohms at different positions, and feeds the info to the computer. That is how the computer decides how much fuel to inject. So if you do not set the TPS correctly, your computer is getting bad info, and not giving the correct fuel amount. It could idle fine, but no power when you step on the peddle. When mine was set wrong, it would idle kind of fast, but when I drove, it felt like my clutch was slipping. Now that mine is set correct, the truck is peppy.

[@WhatAmIGonnaGet]

Hi, thanks for the information. Do you have a link for that print out please?

[@tubejim101]

Google "22re service manual pdf" There are a few of them out there

[@reinaldogonzalez6045]

LCEngineering.com

[@rallen627]

www.4crawler.com/4x4/CheapTricks/TPS/index.shtml

[@stevejette2329]

And the diagram looks like the throttle body side, the open side. But you are looking at the closed side with the label ?

[@tubejim101]

E2 has the blue clip on it. Hope that is what your are asking about.

[@jhuds88]

Thanks man, do you have a link for that diagram that you showed to us?

[@tubejim101]

www.lcengineering.com/LCInstructions/Throttle%20Position%20Sensor%20Adjustment.pdf

[@Jeff82556]

@@tubejim101 PAGE NOT FOUND (a dead link, please update)

[@tubejim101]

@@Jeff82556 lcengineering.com/wp-content/uploads/instructions/Throttle%20Position%20Sensor%20Adjustment.pdf

[@007ayala]

I ordered two screw driver and loved then. Thanks to you. G bless

[@tubejim101]

I tell people all the time about them, but no one believes me, when I tell them how much better they work. It is one of my most used tools.

[@ChaseSaxtonofKy]

What exactly did you have your multimeter set on? Mine for Ohms has settings for 200, 2,000, 20k, 200k and 2000

[@tubejim101]

You set the meter just below what ever value your going to read. So if your going to read a 25,000 ohm value, you would set your meter to 20K. You could have it at 2k, or 200k, but your going to have a harder time figuring out your values, unless you understand converting between, ohms, kilo ohms, and mega ohms.

[@vika.2388]

Actually you should always set the multimeter just above not below or you'll reck your multimeter pretty quick.

[@pianist8744]

Hi Jim, I've made it to this point on my head gasket repair. When I try to remove the throttle body, it is firmly stuck to the plenum. I have removed 3 bolts and the lone nut. Also, the cable has been removed too. Am I leaving something out?

[@tubejim101]

Watch this video and let me know if you still need some help. kzbin.info/www/bejne/qHrWe6F7rdNoh5I

[@pianist8744]

@@tubejim101 I knocked it off with a mallet. It had probably never been removed in the truck's 31 yrs of existence and was fused to the intake.

[@FSria]

That settings are same for tacona 96 2.4 engine 2RZ... thank you.

[@azulmarinoify]

No are different

[@azulmarinoify]

Every engine has different ones

[@straightshooterz]

Very helpful video… but What is ohm converted to kiloohm?

[@tubejim101]

Kilo means thousand. 1,000 ohms, can be written 1k ohms. 1 ohm, can be written .001k ohm. Hope that helps.

[@joe7419]

Good video thank you

[@ultraravvy4.253]

Hey man, great video I was wondering if this exact method also works for other toyota engines?

[@tubejim101]

Not sure. This I have only worked on the 22re

[@yourdaddyjoe]

Thank you so very much!

[@tubejim101]

Your welcome

[@yourdaddyjoe]

@@tubejim101 You helped get my 93 Pickup with over 250K miles on it to pass smog yet another year. I was able to get everything to dialed right in. Damn near 0 emissions with the tune up and regular maintenance. It passed the high rev in less than 30 seconds and idle in under a minute. I owe ya one!

[@emiliomorales9731]

@@yourdaddyjoe did your vehicle fail due to ignition timing? my mechanic said it was the tsp

[@smokeybear4403]

Can someone tell me how big those screws are I checked on mine and my bottom screw was missing

[@tubejim101]

It is worth giving your Toyota dealer a call. The price on the idle air control valve screws, where not to bad. Also, shop around at different dealerships. My local Toyota dealer, price gouges bad. I order all my parts from a city 71 miles away. They deliver for free, and charge 1/2 what my local dealer charges.

[@SnailTrail4x4]

I took the screws that I had stripped to the local hardware store and both the same length and thread but with allen heads

[@nickg6246]

They are M4 screws. www.lceperformance.com/Tools-Allen-Bolt-Upgrade-Kit-For-TPS-p/1093082.htm

[@kawi1999jv]

Hello would adjusting tps on Phillip screws help with cold idle?? In morning at first start my rpm goes lower than normal then once truck is warm it runs better it’s 1986 Toyota pickup 22rte efi engine

[@tubejim101]

If your accelerator peddle is working fine, I would not mess with your throttle position sensor. ODB1 is harder for me to trouble shoot. Would be nice if you could tell what the computer thinks the cold temperature is. There is a air bypass screw you could try adjusting.

[@tubejim101]

kzbin.info/www/bejne/iWmvaoyVj52Crck

[@kawi1999jv]

@@tubejim101 thanks for advice

[@trentbost7503]

Iv put my new one on but I think it’s set wrong because the throttle won’t go all the way down to that pilot screw unless the tps is off but I don’t understand how to gauge it

[@trentbost7503]

I need help

[@reinaldogonzalez6045]

Trent Bost : you have to instal it with the pins facing down and rotate clockwise to horizontal position to put the screws and adjust.

[@juliovelez9863]

Gracias

[@TheIrishdriven]

when putting new tps on should i have tension immediately or should it set loose inside

[@tubejim101]

The tension is from the throttle body spring, on the side opposite, the tps.

[@jesusojeda6310]

Thank you

[@markmahecha8974]

What kind of ohm meter is that?

[@tubejim101]

Mine's a Craftsman 82026. Don't think they make it any more. This one is nice: amzn.to/2TylHdk

[@backtotherootsoutdoors4306]

What gauge sizes did u stack ?? You did not say gauge size to stack cause mine are not right either

[@tubejim101]

Just add things up. So if you need .8 and you only have .5, just stack a .3. .5 +.3=.8

[@backtotherootsoutdoors4306]

@@tubejim101 I did that got it Close as I could

[@jsngrmjo8525]

So when you did step 3 to get infinite wht size gauge you had between the stop screw and lever?

[@tubejim101]

.85mm

[@jsngrmjo8525]

@@tubejim101 thanks

[@jsngrmjo8525]

@@tubejim101 if you don't mind what's an open or infinite reading

[@tubejim101]

@@jsngrmjo8525 If you hold the leads up in the air, and measure resistance, it is open, or infinite. Basically it is a break in the circuit.

[@jsngrmjo8525]

@@tubejim101 ok but what should my ohmm meter read all kinds of numbers?

[@chrislisowski169]

Where can you get the speck sheet from?

[@chacholiades]

here lcengineering.com/throttle-position-sensor-adjustment/

[@shantamarshall3114]

thanks

[@stevesmothers8018]

Hi! So what exactly what would be adjusted if the readings are out of spec?

[@tubejim101]

What values are you getting at each step?

[@tomasjrvillanueva9008]

Doe this apply to Toyota 1RZ-E

[@tubejim101]

Sorry, only know a little about the 22re

[@yourdaddyjoe]

BTW - I was able to find a NEW Genuine OEM Toyota 89452-12040 TPS (Throttle Position Sensor) on eBay for less than $24.00

[@tubejim101]

Nice find.

[@reinaldogonzalez6045]

Yes, I get one, thanks

[@Raevenswood]

actually a quicker way to do this is to just immediately do the open infinite .85mm setting first because if you get that one right the other settings should be right so you just stick the .57mm feeler in to verify that it's less than 2.3k ohm.

[@Raevenswood]

ahh and you figured that out already. my bad.

[@Jon-uj2uw]

Quarter inch turn? Which way ??

[@tubejim101]

Which ever way backs the flap off.

[@elijahlawrence7132]

Quarter turn*

[@andym.4029]

Thx but I simply can NOT get both the IDL @ .85mm (to Inf) AND VTA @ .5mm (

[@tubejim101]

I have only worked on the 22re

[@barnesj0007]

I've been dealing with same aggravating circumstances so you're not alone on issues...

[@slumpnc]

@@barnesj0007 Main problem was distributor but idle & TPS still off so messing with those 2 now, doesn't idle down after warmup, sometimes shudder on road and/or idle bouncing between 2 spots. One manual says when installing TPS just get IDL to infinite w/ a .62 feeler (kind of midway)

[@barnesj0007]

@@slumpnc I ordered a new Mass Air Flow for air intake off Amazon and truck running good now. Make sure you check all wiring to electrical so that there is solid connrctions. I noticed that some were dry rotted and barely clipped into harness as well. 👍

[@annhenry1226]

can't see where the feeler gauge is going

[@JoseGarcia-yl1dg]

I just can't get step 2 to work, would some help

[@tubejim101]

Maybe ask a shop how much they would charge to set it up for you.

[@natalied989]

I cant either. All the others work but for test 2 I either get infinity or with the SLIGHTEST tap it goes to 10000 (supposed to be 2000 to 3000). Ive tried 700 times. There is no in between infinity and 10000. Its a brand new tps from Toyota dealer and the reason I put the new one on is because when I tested the old one it did the exact same thing with test 2. So it's not a bad sensor from the factory because the one I took off was probably 30 years old so it's not like they both came from the same defective batch.

[@ipaint00]

TheTPS diagram shows the guts facing up so you have It reversed...i believe

[@stevejette2329]

Heck with Philips and vessel !! On the vehicle, there is no room for a screwdriver. Replace with Allen wrench setup. Horrible to perfect.

[@tubejim101]

Good idea!

[@reinaldogonzalez6045]

I just ordered the kit.

[@SnailTrail4x4]

I did the same thing!

[@Toyotas_n__Tools]

THANK YOU!!!! My Vessel P3x150 came this week right from j a pan! Love vessel phillips heads AKA jis! excellent video! Check mine out if you like tools =)

[@tubejim101]

Yep. Love my jis too.

[@michaelspong2056]

What are the recommended sizes of Vessel drivers to buy for the Japanese vehicles ?

[@tubejim101]

@@michaelspong2056 I like the P2x100 amzn.to/2K6hPZj

[@Toyotas_n__Tools]

@@michaelspong2056 I got the 1 , 2 and 3 for my truck. I just posted a video with my new #3 vessel impacta. I should be able to answer most Japanese tool questions, I hope =)