Setting Valve Spring Height and Spring Coil Bind (Predator 212,Clone 196cc,Go kart racing,Mini bike)

[@NubsWithGuns]

I should have just watched this video.😂😅 36:47 Could have saved you the time of emailing me'😂 Regardless Jody is great, had an answer almost right away. Thank You

[@HTHCLLC]

As a dad you seem to understand.....we can no longer tool around in "our" John Deer...Buck naked. But he can....Ride boy Ride. To soon he will join the the rest of us......(wishing we could.) I love that you didn't say....(Stop)....you close the door and let boys "BE" boys. (Salute to you sir)......O yea, nice info on valve springs, only 36 min in, but had to comment.... Back to the video :)

[@danparamore5854]

HTHC

[@minibikemadman]

with a stainless steel 5.5mm valve kit 26lb springs on a hemi, im getting coil bind now, do you need to take a lot out when machining the spring pockets. Im on a black mamba jr cam 275 lift 104 lsa.

[@joeyhightower870]

I got the short 18lb valve springs what should I set the intake and exhaust lash on that. And that's on a predator 212 Hemi

[@christophermcmahon7920]

I'm going g with red stripe or dual springs on a hemi. 1.2:1 rockers f275 cam. Gonna cut the pockets out bigger for the wider springs. Do I need to go deeper as well?

[@christophermcmahon7920]

Sorry hemi head with valve reliefs cut already in piston. The billet ratio rockers. Springs say 42lbs at .840 install height and 80lbs at .670 install height.

[@toymango71]

Cam vs 1.3:1 rockers? What's your thoughts? Stock HF 212 governor removed. Thanks

[@kiixgviikk4270]

❓ IM BUYING PARTS AND I WANT THE BEST PERFORMANCE PARTS COMBO ANY SUGGESTIONS. IM GOING TO GET A MIKUNI 26MM CARB INTAKE, IS THAT COOL FOR MY HEMI WITH 27MM INTAKE VALVE?

[@arcracing7637]

CALL 800-521-3560 ASK FOR JODY

[@jonah.c.strickland8400]

Ok I have stainless valves in a 14cc head- dyno 335 cam 1:1 champion rockers i got some 36lb dual springs with the seal in the inner spring sets higher is that normal ?

[@arcracing7637]

take the seal out

[@Dirtypigeon]

stock 196cc clone 38 main jet stock emulsion tube stock carb about a 12 inch header no filter 18lb springs how many rpms should it be at

[@arcracing7637]

18 lb spring are good at 7200-7400 rpms

[@Dirtypigeon]

ARC RACING best way to clearance my crank to rod

[@arcracing7637]

kzbin.info/www/bejne/pajEmaOFmrGMl9k

[@frankfitzpatrick5300]

Would #20lb. valve springs produce a somewhat higher rpm than 7000-7400. rpm on that same particular engine configuration . Or is that going to go the other way & add to much resistance on a basically stock engine ? Sincerly, Thanks in advance

[@PAiN46k]

Would you know the valve lash for 212cc non Hemi with 18lb Springs?

[@arcracing7637]

zero cold

[@roonimac]

@@arcracing7637 is that the same with 22lb?

[@arcracing7637]

same

[@richardjuel3616]

I really like your knowledge of the Predator motor you explain it very well and the one I watch the setting your valve spring clearance and you are using your wife's iPhone you really got to spend the time to set your phone up and your camera to where we can see what you're doing in that engine head it does no good to take your custom bent pliers and start pulling on stuff when I can't see it it does me no good so I would go back and watch your video that you made there and see if you're actually helping people you helped me a great deal deal with the way you explained it verbally but video you don't see anything except it's like watching a dentist you can't see what they thought he or she is doing unless you right where he is well I'm not where you are so so I would definitely watch your video and figure out your camera angle cuz it's not helping that's the only thing I got to say about your videos are perfect except you got to get that camera down