Choosing the correct carb, cam, valves and springs(Predator 212,Clone 196cc, Go kart racing)

[@jeremymoore2411]

Thanks for your time and making these

[@JimCooper-f8g]

I set push rod length so rocker is close to parallel with valve cover surface at about 1/2 of valve travel providing rocker is centered on tip of valve at that point.

[@goodboyringo9716]

I'm wishing ARC would deal with 420/460 engines a little more.

[@samstewart4807]

I think Jessel has a good valvetrain geo video. You want correct rocker geo. Just like a race engine.

[@eddiedoran7427]

Rock & Roll,Jody

[@wescryer5503]

I have a predator Hemi. ARC Flywheel, ARC Rod, ARC SS Valve Kit 25/27MM w/ 26lb springs, Dyno 265 CL-CM Cam, thin headgasket, 22mm Mikuni Carb. I want to get 1.2 or 1.3 ratio rockers. You mention at the 19:00 mark its a good combo for this cam. Would I need to worry about valve to piston clearance? Also would you recommend me going to a bigger carb? Engine is a in a 1970 Stinger by Bug chassis I restored.

[@LucidReclusion]

Did you ever end up going anywhere with this?

[@Jayhla1]

Did you have to do any clearances for the 265 cam I would like to know please

[@MarkMorse-kh1db]

What would be the best setup for a 196 cologne. I'm talking about best cam best Valves valve keepers valve springs and spark plug I currently have a Mackenzie 22 mm carburetor jetted exhaust header spark plugs and exhaust pipe headpipe and silencer what route would you take next

[@johnrisher3007]

i have a 16 hp horizontal opposed box engine. Is there any parts to add hp. i would like to get as much as possible. I'm planning on building a light weight airplane single seat

[@bsimpson4158]

What would be a good med clone akra set up

[@jimmycooper7248]

Have you ever worked with the heads that came on the early mega moto 212 mini bikes? Mine has round ports on both sides and a 28.5mm intake valve bone stock as I know it. Wondered what you thought about the potential of these as well. How do you like the Wildcat hemi heads as well?

[@dannyskidmore1240]

Stock Hemi which cam which Springs

[@4687878]

If you take off the governor,..what is required to have upgraded,..so you don't ruin your engine ?Are 18 lb springs, air filter, jets, and 140 E tube enough,..or do you have to do billet rod and flywheel, also ?

[@ninoreeves7702]

billet flywheel is for safety. your stock one will crack, possibly explode. some are only 65$ hemi's run a little more like 110$

[@asphaltcowboy7868]

I'm currently running a 265 cam..with 22lb valve springs..I have done the stage 4 kit..but my issue is..it runs great at bottom and mid rpms, but once I give it wot, it wants to fall on its face and cut out at around 7,800 rpms..what's the problem? I'm wanting to reach around 9k if possible

[@jjmccloud]

Not enough fuel?

[@asphaltcowboy7868]

@@jjmccloud I'm currently using a 24vm mukuni

[@samstewart4807]

I think Smokey also said it aint cheaten unless your are caught.

[@samuelskeyon4513]

whats is the best setup for the dynocams tool steel billet 308 cam shaft in a 212 predator ?

[@arcracing7637]

Please call 800-521-3560 tech line and ask for Jody

[@soaring16]

I run a stock Predator Hemi with governor removed. Stock intake and exhaust. Is there a benefit to running your springs over stock and why? DJ-1055HD 10.8lb HD Valve Spring Set

[@dubc313]

Will everything spec wise that fits the predator fit the new tillotson 212? Hard to find much info, any given helps. Thx

[@theoldfartschannel3692]

No. Tillotson uses the Ducar platform which uses the Honda flywheel taper and crank journal. You can use a Honda rod with a Predator piston. The Tillotson Ducar piston has a larger wristpin.

[@bradley1995]

I've got a non hemi 212 predator. I'm looking into getting some new stuff for it. I ride lots of dirt primarily. I love torq which I have decent amounts but I want more top end. Would the mod2 with a vm22 mikuni work decent with a stock head? Also which size rockers would be the best? I was thinking bout the 1:1 and I was thinking bout the 18lb valve springs. Any advice would be very much appreciated. Thanks for the video arc!

[@Amy-wh3dt]

Will a mod2 work in a 212 hemi without having to grind on the crank

[@arcracing7637]

This is why we sell the Mod 2 Hemi cam from Dynocams. You sould not have to do any further clearancing.

[@ryanrohauer5940]

intake reversion. please do a video on intake reversion plz im stumped my bike idles like shit and is sooooo rich at low rpm and screrams up top. at around 3500 rpm at WOT im getting really bad intake reversion using a 22mm mikuni and 1in exhaust. im starting to think the exhaust is to big and is allowing combustion to go out the intake during valve over lap. would love some advice

[@arcracing7637]

please give us a call at 800-521-3560 ask for hunter

[@alphamoto466]

how much rpm do 18lb springs produce?

[@arcracing7637]

Depending on valve size around 6600 to 7200. be sure to check for coil bind

[@alphamoto466]

what about 22lb and 26lb and what parts needed to safely run them

[@alphamoto466]

i wanna make at least 8000rpm easily

[@arcracing7637]

At the least you will need 26lb springs and a hardened cam. Give us a call to discuss more at 800-521-3560 ask for hunter. Thank you

[@newscooler12316]

have you guys tested ram air intakes?

[@arcracing7637]

No we have not.

[@newscooler12316]

ok thanks. would 18lb springs be ok with 1.3-1 rockers and bsp 4 cam?

[@arcracing7637]

no the 18lb spring will not handle those rockers.

[@newscooler12316]

ARC RACING ok thanks again

[@chanzhope8824]

I,'ve got a stock gx 340 carb . can I use it on my predator 212 ,with a stage 1 kit.

[@arcracing7637]

More than likely it is the same but we have not played with the 340 carbs. Measure the center to center distance of the mounting studs if it is 52.30mm it should fit.

[@travis48g]

"Cheaters and Losers".LMAO

[@Alainanaomi13]

try 19 20s average 70 mph chrisp motorsports park

[@chadbrown-i4d]

ummmm uhhhh just get to the point uhmmm