Shimano EP8 E-Bike Motor Unit Installation. Enduro E-Bike Build - Part 2.

[@VarjoYT]

Wiem Szaju, że chciałeś zrobić szybkie przedstawienie montażu, ale dwie kwestie wymagają sprostowania: 1. Używajcie TL-EW02. (to szeroko dostępny klucz, a bez niego mogą odrzucić reklamację uszkodzonego kabla [kombinerkami?!, przecież ten rower jeszcze nie zaczął jeździć a wtyczki przy silniku wyglądają jak by je coś przejechało...]) 2. TL-FC39 to niezbędny klucz do montażu zębatki, nowy silnik przychodzi bez mocowania ("pająka" zębatki przedniej) które tutaj jest prezentuje na filmie jako część całej jednostki. 1. Use: TL-EW02. (this is simple tool, without it, you can lose warranty if uou broke cable or sth) 2. You propably don't have TL-FC39, but it will be nesessery if someone want to replace unit. (to get on place chainring mount)

[@frakafrocka]

this vid is truly outstanding.

[@davidmackey74]

This would have taken me longer to do,I like a cup of coffee in between steps and procedure's maybe a sandwich. Happy biking everyone!

[@davidmackey74]

There is a lot you can do with any bike. Nice video.

[@scott5731]

That exposed foam around the motor looks concerning. Can see a lot of crap getting jammed in there

[@brizi2003]

Outstanding vid though 👍

[@jrponti2206]

What kind of handle bars are you using?

[@HerrKalus]

Hey👋🏼 One question: Where is the on/off switch connected?

[@user-hy4ox1ye3b]

Can't find part 1, did you do one?

[@rhpino]

será compatible el visor del e8000 cambiando los cables de sd50 a sd300 claramente ? ( me da la impresión que es mas grande el del e8000 )

[@wannabepioneer]

Awesome video, but how do you connect the tiny power wire to display unit on the handlebar?

[@Smegmeister]

EWAD305

[@jdvaldivia]

Hi! If I want to use SRAM eagle transmission, can I use the same crank Spider and put a 104 BCD SRAM XSYNC-2 chainring? What about the chainline? Thanks!

[@luisangelcurielsanz8329]

What display is that? I wonder if the sc em-800 comes with a light port also...

[@Giovanpire]

Parabéns!

[@franzleis9874]

Did you glue the damping foam on the motor or was it already on the motor. I want to build an e-bike on my own and am looking for good damping of the motor. Can you give me some advice, what is suitable for that? Thanks

[@YukiKawaiUltimatum]

EPDM rubber foam tape

[@diegoflorencio3705]

👏👏👏 AWESOME ❤️

[@minecraftbender]

Hey bit of a niche question but do you know how long the cable from the screen to the motor is? 1200 mm or 1400 mm

[@najarmouhamed6853]

Can i ask please which better for m'y ebike a triple or a single chainring????

[@johnnywallace8123]

I can't find part one.

[@robert1975e]

What’s the cost to remove and install a new one?

[@magzire]

can you still cycle normal?

[@TheWeardale1]

great, one question tho - is there a sensor that goes on the back wheel so the bikes knows how fast you're going?

[@КириллСандалькин]

Yes, it’s a speed sensor.

[@TheWeardale1]

@@КириллСандалькин many thanks, i later found out...just i got a new ebike and it came with a spare magnet - and i thought it was the one i had to use...

[@markifi]

is it true that these only go 20 thousand kilometres at most, before they're toast? so about 10 cents per kilometre just for the motor?

[@cannondany]

So far I made about 10000 km on the E8000 and it works great.

[@HansensUniverseT-A]

I think that sounds about right considering these are none serviceable units, not designed to be serviced by it's owner, not that they can't be repaired but for your average mechanic this will likely be a big undertaking and then finding the replacement parts for it, this is why i just stick to higher powered hub motors instead, cheap, reliable but effective enough.

[@calilthomas]

Do you think it's easy to remove the battery and motor of an Orbea Rise?

[@edgardomunoz6611]

Done it. There are several frame design differences that make it much harder in the case of the Rise. Most notably, the front end needs to be placed first, in between spacers that are very tight, and keep falling out of place while you jam the motor in place. This Merida is specifically designed for easy ep8 install.

[@davidhudson8960]

I'm not seeing anything that would prevent retrofit to e7000/e8000 bikes. Wonder what the true compatibility is with older hardware/harness etc. I know Shimano won't sell aftermarket but sometimes enterprising people find a way...

[@halfbrain86]

Can anybody tell me if it's possible to fit some cranks with integrated powermeters to this motor and if so which? I would like to have my rider power tracked via ANT+. Specialized has that integrated in their system but as far as I know the EP8 is not broadcasting that data via ANT+ 😞

[@MaciekP2]

Zdecydowanie polecam jednak przednią zębatkę stalową bo ta sprawia wrażenie aluminiowej. Przy wadze elektryka nie ma to znaczenia a trwałość znacznie większa i wolniejsze zużywanie także łańcucha

[@ziasin]

Hola por favor alguien sabe donde va conectado el interruptor de on of SW300

[@237311]

Where can I purchase this kind of motor?

[@tsalesto]

Where did you get the motor from? Asking for a friend ;)

[@TURBOGHIA6]

it came with the bike

[@honeybadgerflys8162]

when the bike cost more then the car. lol

[@blainebickle1178]

*than

[@vyankateshmundhada5760]

Total how much it cost you

[@pvenkat316]

I want this cycle how to purchase

[@redtobertshateshandles]

Aussie KZbin guy does this and says it's actually no more powerful than an e8000.

[@Mobimanie]

Hey Danny, why are you no longer talking to us...?

[@cannondany]

Oh, I will yet talk a lot 😃

[@Mobimanie]

@@cannondany looking forward to it!😀

[@brizi2003]

Chain ring looked like it was on backwards??

[@cleggycyclist]

3:41

[@Vera_gacha565]

умеете могёте

[@user-bt8vp3hn4l]

Price koto

[@user-bt8vp3hn4l]

Hello

[@Perkalowy]

Tee ile to zapierdala

[@DM-hw4cr]

Can't see it surviving wet rides

[@ozPanzer]

Everyone else can.

[@user-hy4ox1ye3b]

It does

[@lotus4405]

오토바이야 자전거야? 이가격이면 오토바이 산다.