How to use A Rivet Nut Tool or Nutsert Rivet Tool

Рет қаралды 39,794

Күн бұрын

Пікірлер: 25

@petemoore8923 6 ай бұрын

Three pumps and you’re good. Brings me back to when I was 16. All BS aside, I’m glad I saw this video. I use rivnuts pretty often. The manufacturer of the product we install them on supplies the rivnut, Allen key and instructions on how to install them using said Allen key and an open end wrench. AND THEY SUCK!!! Thank you sir!

@shopandmath 6 ай бұрын

well, this would put a smile on my face. Thank you for that. And thank you for taking the time to comment. It is much appreciated.

@charlesspringer4709 5 ай бұрын

Knowing about the spring-loaded sleeve makes all the difference 🙂 Thanks.

@shopandmath 2 ай бұрын

Glad you found the video helpful thank you for commenting. It is much appreciated. Ray

@marshonhaynes 3 ай бұрын

Thank you sir this was my first time using one at work .

@shopandmath 3 ай бұрын

Hopefully this video helped you. Thank you for taking the time to comment. It is much appreciated.

@daugbret Ай бұрын

Thanks. Just had to use one of these at work. Helped me figure out what I was doing wrong.

@elkebaumgartner6818 11 ай бұрын

Love watching your videos. Thanks!

@shopandmath 11 ай бұрын

Thank you so much for your nice comment and thank you for taking the time to comment. It is much appreciated.

@great0789 4 ай бұрын

Thank you. I am adding a bunch to my Jon not build… I shall now go back over them and make sure they were fully crimped! I stopped at the first squeeze.

@shopandmath 2 ай бұрын

Excellent I’m glad that you found the video useful And thank you for taking the time to comment. It is much appreciated.

@andyb7754 11 ай бұрын

Very good video. I would have deburred the hole using a Cogsdill deburring tool or a countersink (that's just me). Thank you for the video.

@shopandmath 11 ай бұрын

That’s a good point. Thank you for sharing. There wasn’t much of a burr, and I was thinking that that would help grip the insert little bit more of a jagged surface Or do you think it’s best to bur the surface so it’s clean

@andyb7754 11 ай бұрын

As an aircraft mechanic we always de-burred the holes front and rear using a Cogsdill tool to clean up and prevent cracking when riveting. I've always de-burred any hole just as a measure to get a solid flat surface to bond anything to. As for that panel, it's perfect as it is. Just a little FYI of how I was taught. Thank you for your videos.

@roybrookton7938 5 ай бұрын

Great information 👍 thank

@shopandmath 3 ай бұрын

Thank you for nice comment and thank you for taking the time to comment. It is much appreciated.

@THCGraps 8 ай бұрын

guys DO NOT stick your head inbetween the handles that shid hurts (dont ask how i know...)

@shopandmath 8 ай бұрын

Good one thank you for sharing

@diegoangulo370 5 ай бұрын

Ha good technique ✌

@shopandmath 3 ай бұрын

Thank you for the nice comment and thank you for taking the time to comment. It is much appreciated.

@wt9653 7 ай бұрын

The tool itself is fine. The rivot nuts are junk. 2 out of 3 threads stripped

@shopandmath 7 ай бұрын

I’m not saying this is what it is but you need to double check to make certain that the tool insert has not been stripped. I have a 6 mm insert for this tool that I’ve stripped out because all of my nut Certs are stainless steel and the damage the six mill insert for the tool check your threaded tool part and see if the threads are stretched or damaged.

@wt9653 7 ай бұрын

@@shopandmath I found out why from watching other videos. You're not supposed to thread the rivot nuts all the way. When squeezing the handle, it should close easily. Once closed, you give it a couple of turns on the thread and squeeze again. It works every time now.