Simple Haslab Proton Pack Upgrades

I love my Haslab Proton Pack but I wanted to make some upgrades to it. Check out these simple and easy mods that anyone can do with basic tools and supplies!
Update: the washer I use in the cable clamp is 3/8” outside diameter.
Alice frame: amzn.to/3ZB8lMB
Nutrona Wand grip:
cults3d.com/en/3d-model/vario...
Don't have a 3D printer? Pick up this pre-printed grip for your Nutrona Wand here: www.etsy.com/listing/12997176...
Or get your own Elegoo Saturn here:
amzn.to/3ZINgjT
Don’t forget to SUBSCRIBE to the KZbin channel so you can get notified about new episodes and live streams!
bit.ly/MADEbyAPsubscribe
______________________________________________
Follow Me
/ mbap77
/ madebyap
/ madebyap
/ mbap77
______________________________________________
Want to Support the Channel?
Do you like the work I’m doing? Want to support this humble maker? Consider tossing me a couple dollars:
ko-fi.com/madebyap
______________________________________________
Credits
80's Music retrieved from www.dargolan-free.com/time-ma...
______________________________________________
Chapters
00:00 Cheap and Easy Haslab Proton Pack Upgrades
01:55 How to add an Alice Frame to a Proton Pack
05:18 How to add a neck pad to an Alice Frame
09:03 Adjusting the wire loom on the Haslab Proton Pack
11:42 Adding real cable clamps to the Haslab Proton Pack
13:39 Adding real wires to the wire loom on the Haslab Proton Pack
18:18 Wrap-up
______________________________________________
Disclaimer
The product links above are affiliate links so I get a few cents to go towards funding future projects (so THANK YOU!)
#haslab #cosplay #ghostbusters

[@harsin3dprinting]

Stumbled across your video today. I'm the one who made those snap-on grips for the neutrona wand! Thank you very much for linking to our shop and the Cult3D link too!

[@MADEbyAP]

That’s awesome! Thanks for making it. Holding strong and looks great!

[@Or_else_it_gets_the_hose_again]

Without the orange tip, everyone will think it can actually shoot a charged particle beam composed of protons.

[@MADEbyAP]

😂 sadly true!

[@Sammo212]

Very cool. I used a 3D printed bit for the front grip on the "wooden" bit and also cut off the back grip and used a 3D printed grip there as well. Covered both in black hockey tape too. I need to replace those clamps, they look snazzy.

[@MADEbyAP]

The clamps really take it up a notch for sure! Love that there are so many mods available to do on this!

[@raynekraven]

the only mod I intend to do, which is done, is a no-time out chip.

[@MADEbyAP]

Yeah that’s one I need to do. An upgrade the power supply!

[@docdeth904]

I was going to mod my Haslab, however, Spirit came out with their full sized GB1984 pack, so I will keep it stock and mod the less expensive pack instead.

[@SirFunky]

shittier pack*

[@daviddyer1919]

Excellent video. I was wondering if the cable that the yellow sleeve goes on the attaches to the cyclatron pull out or unscrew.

[@MADEbyAP]

Thank you! So the end that plugs into the cyclotron just pulls out. The end that is attached to the actual pack though goes through a hole and then is attached somehow to the inside of the pack. You’d probably have to remove the backside of the pack to access it. Hope that helps!

[@daviddyer1919]

@MADEbyAP it helps heaps mate. Thank you for taking the time to reply.

[@daviddyer1919]

When cutting the soft fake wire loom to push the wires in is there anything to be careful of while cutting into it like real wiring for the pack.

[@MADEbyAP]

Hi there, that section that I cut out, there's a hard plastic piece underneath that I believe protects the cables running to the pack. I'd suggest leaving that in and just pressure pushing your new wires in. Hope that helps! Check this section out: kzbin.info/www/bejne/gZzElYCig7qYf5Isi=Ut6Syc_c5LV_Vqi2&t=887

[@mcdixon]

You used the stock screw for the cable clamp, right? What was the size of the washer you used?

[@MADEbyAP]

Hi yes I reused the stock screw and the washer is actually 3/8”. Hope that helps!

[@mcdixon]

@@MADEbyAP do you have a home depot link or something alike that I can use for reference? I've seen different types when I look one up.

[@MADEbyAP]

Hi sorry I had turkey on my brain. The outer dimension was 3/8 but it’s actually an M4 washer. Try this link www.homedepot.com/p/Hillman-Stainless-Steel-Metric-Flat-Washer-M4-Screw-Size-4118/204801237

[@bedfordshiremodeller4491]

Will you be doing away with the 4D battery powersource? As that,s highly flawed

[@MADEbyAP]

Probably. I actually am starting a new list of things to upgrade like adding the “always on” circuit and maybe adjusting some of the lights. There’s a part two in the future I’m sure haha.

[@Sammo212]

it is super easy to do! I swapped mine out the other day and will eventually completely remove the plastic housing to cut down on the weight.

[@bedfordshiremodeller4491]

You remind me alil bit of Bruce Campbell you,ve got his nose but not his chin lols!

[@MADEbyAP]

Lol amazing. One other person has told me that! I’ve also gotten Johnny Knoxville. Completely different ends of the spectrum haha.

[@bedfordshiremodeller4491]

@@MADEbyAP I know lols!

[@txag007]

I was thinking the same thing as watching his video!