Single ESC Mount a Dual Drive ESK8 | MINI FSESC4.20 Canbus Connector 6374 Battle Harnded | Flipsky

[@rn2379]

What's the purpose of the green board in the battery pack? Is it a charger or BMS?

[@FlipskyTech]

Hello, sir. Thanks for your message. It's a BMS.

[@brandoncheaa]

The female connectors you have attached to the esc for power and motor control, what are those called. I'm trying to find the wires for them.

[@FlipskyTech]

Hello, Sir/Madam, we have received the feedback about your professional question. If you need technical support, you can contact our email at [e-mail] or click online support at the bottom of our official website. flipsky.net/pages/faqs?contact%5Bcontext%5D=footer&contact%5Btags%5D=prospect%2Cnewsletter&form_type=customer#newsletter-footer

[@emilj.4766]

is the breaking good and do you have regenerative breaking turned on?

[@garrettallain9343]

Appreciate the video. This is definitely going to help me figure out my setup. Quick question: s the antispark connector a must?

[@FlipskyTech]

It is safer and more convenient to have anti- spark switch on esk8.Undoubtedly a necessary choice, bro!

[@garrettallain9343]

@@FlipskyTech thanks for the reply. Will be buying one today, thanks!

[@joshuamcmurtrie7863]

Definitely blown 2 vesc already without it

[@ZacharyC]

I just got mine and I was wondering if you're supposed to take the plastic wrap off?

[@FlipskyTech]

Hi , the plastic shell can block a certain amount of dust, so it is not recommended to remove it.

[@ZacharyC]

@@FlipskyTech Okay thank you! I will keep it on

[@chrisgayle1623]

What is the difference between using a Dual vesc and 2 separate singles?

[@FlipskyTech]

The size of the dual vesc will be smaller, which is suitable for most people's battery box. If there's not enough budget, combine two single-drive ESCs into a dual-drive is also a good choice.

[@samuelchristopher4506]

If you have space..bettet buy singles One breaks, you replace one. Dual breaks, another story

[@gregdeli5859]

Do you connect to power cable of the electric throttle to 3.3V or to 5V?

[@FlipskyTech]

Both of them are ok.

[@damichl9684]

Hammer build. But what I don't understand about your device. You have installed 2 of the most powerful burshless motors. 2 x 3250 watts! That's 6500 watts and at 37v 176 amps! And then you only use Li-Ion batteries? When fully charged, these can only deliver 20 amps. That means you have a Porsche engine but only one needle as a fuel hose. Of course you have an extremely good range and capacity with Li-Ion. But then you don't need 6374 motors. You definitely don't need that much power on a board anyway unless you have big slopes. But then your bottleneck is definitely the battery Please correct me if I'm wrong - I want to build one myself and I liked your video very much

[@FlipskyTech]

The battery brand LG HG2, one battery current is 20A, four sections together 80A. Thank you for liking our videos and affirming our motor 6374-Porsche :) . Welcome to consult other questions about DIY electric skateboards:flipsky.net

[@blise518B]

Also the 3250W is just maximum archivable power not continuous. It would overheat pretty quickly if you run it at over 3000W for extended periods of time.

[@BestJulian14]

Could someone tell me where the plastic part that is holding the battery is from?

[@FlipskyTech]

Customized battery enclosure in China , bro :)

[@kastelvani7259]

Can i use uart mode with this setup ?

[@blise518B]

Yes .No problem.

[@kastelvani7259]

Because i try it with 2 Besc conected via can bus an it didnt work in uart mode

[@FlipskyTech]

Hello，which remote is it? If you used ppm before, you need to change to the uart mode before using . If possible, pls send your parameters setting video to [e-mail], thanks! We are back to work today.

[@kastelvani7259]

@@FlipskyTech i use the Flipsky Vx1 yes i used ppm before, but reset the Vesc to defualt....

[@FlipskyTech]

Yes, need to select again: APP Settings-General-APP to Use-UART

[@Kevin5Nguyen]

I thought FSESC4.20 is rated for 50amps. Why is the auto detection say 55 amps per motor? Is that safe?

[@FlipskyTech]

Yes safe, because VEST TOOL automatically detects the maximum current, and the instantaneous current of FSESC4.20 is 150A . See details here:bit.ly/3eZJ0Gk

[@Kevin5Nguyen]

@@FlipskyTech oh wow! Very cool, thank you!

[@FlipskyTech]

@@Kevin5Nguyen You're welcome:)

[@steelavocado1]

ngl that parallel connecter looks jank af... but hey, it works haha

[@FlipskyTech]

Yes, Small accessory, big effect!

[@achmadmaruf94]

around 10-11 years ago, someone connecting 2 motor to 1 esc.......

[@FlipskyTech]

I guess you mean a dual fsesc?

[@achmadmaruf94]

@@FlipskyTechit's looks like an esc for RC car....

[@FlipskyTech]

@@achmadmaruf94 This dual esc also control two motors:flipsky.net/collections/electronic-products/products/dual-fsesc6-6-plus-based-on-vesc6